Re: [PATCH 1/2] net:stmmac: dwmac-mediatek: add support for mt2712

biao huang
2018-10-30T07:16:52Z

Thanks for your nice comments.
On Mon, 2018-10-29 at 11:08 +0100, Corentin Labbe wrote:
> Hello
> I have some minor comments below
>
> On Mon, Oct 29, 2018 at 11:04:53AM +0800, Biao Huang wrote:
> > Add Ethernet support for MediaTek SoCs from the mt2712 family
> >
> > Signed-off-by: Biao Huang <biao.huang@mediatek.com>
> > ---
> > drivers/net/ethernet/stmicro/stmmac/Kconfig | 8 +
> > drivers/net/ethernet/stmicro/stmmac/Makefile | 1 +
> > .../net/ethernet/stmicro/stmmac/dwmac-mediatek.c | 364 ++++++++++++++++++++
> > 3 files changed, 373 insertions(+)
> > create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c
> >
> > diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig
> > index edf2036..76d779e 100644
> > --- a/drivers/net/ethernet/stmicro/stmmac/Kconfig
> > +++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig
> > @@ -75,6 +75,14 @@ config DWMAC_LPC18XX
> > ---help---
> > Support for NXP LPC18xx/43xx DWMAC Ethernet.
> >
> > +config DWMAC_MEDIATEK
> > + tristate "MediaTek MT27xx GMAC support"
> > + depends on OF
>
> You should add something like && (COMPILE_TEST || ARCH_MEDIATEK)
ok, I'll add it in next patch.
>
> [...]
> > diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c
> > new file mode 100644
> > index 0000000..9ccf3a5
> > --- /dev/null
> > +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c
> > @@ -0,0 +1,364 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +//
> > +// Copyright (c) 2018 MediaTek Inc.
>
> Only SPDX can use the // comment style, the rest should use /**/
will fix it.
>
>
> [...]
> > +static int mt2712_set_interface(struct mediatek_dwmac_plat_data *plat)
> > +{
> > + int rmii_rxc = plat->rmii_rxc ? RMII_CLK_SRC_RXC : 0;
> > + u32 intf_val = 0;
> > +
> > + /* select phy interface in top control domain */
> > + switch (plat->phy_mode) {
> > + case PHY_INTERFACE_MODE_MII:
> > + intf_val |= PHY_INTF_MII_GMII;
> > + break;
> > + case PHY_INTERFACE_MODE_RMII:
> > + intf_val |= PHY_INTF_RMII;
> > + intf_val |= rmii_rxc;
> > + break;
> > + case PHY_INTERFACE_MODE_RGMII:
> > + case PHY_INTERFACE_MODE_RGMII_TXID:
> > + case PHY_INTERFACE_MODE_RGMII_RXID:
> > + case PHY_INTERFACE_MODE_RGMII_ID:
> > + intf_val |= PHY_INTF_RGMII;
> > + break;
> > + default:
> > + pr_err("phy interface not support\n");
>
> I think you could use dev_err() instead.
> And I think it is better spelled "not supported".
yes, take it.
>
>
> [...]
> > +static int mediatek_dwmac_probe(struct platform_device *pdev)
> > +{
> > + int ret = 0;
> > + struct plat_stmmacenet_data *plat_dat;
> > + struct stmmac_resources stmmac_res;
> > + struct mediatek_dwmac_plat_data *priv_plat;
> > +
> > + priv_plat = devm_kzalloc(&pdev->dev, sizeof(*priv_plat), GFP_KERNEL);
> > + if (!priv_plat)
> > + return -ENOMEM;
> > +
> > + priv_plat->variant = of_device_get_match_data(&pdev->dev);
> > + if (!priv_plat->variant) {
> > + dev_err(&pdev->dev, "Missing dwmac-mediatek variant\n");
> > + return -EINVAL;
> > + }
> > +
> > + priv_plat->dev = &pdev->dev;
> > + priv_plat->np = pdev->dev.of_node;
> > + priv_plat->phy_mode = of_get_phy_mode(priv_plat->np);
> > +
> > + ret = mediatek_dwmac_config_dt(priv_plat);
> > + if (ret)
> > + return ret;
> > +
> > + ret = stmmac_get_platform_resources(pdev, &stmmac_res);
> > + if (ret)
> > + return ret;
> > +
> > + plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac);
> > + if (IS_ERR(plat_dat))
> > + return PTR_ERR(plat_dat);
> > +
> > + plat_dat->interface = priv_plat->phy_mode;
> > + /* clk_csr_i = 250-300MHz & MDC = clk_csr_i/124 */
> > + plat_dat->clk_csr = 5;
> > + plat_dat->has_gmac4 = 1;
> > + plat_dat->has_gmac = 0;
> > + plat_dat->pmt = 0;
> > + plat_dat->maxmtu = 1500;
>
> ETH_DATA_LEN ?
how about getting maxmtu from device tree rather than assignment here?
>
> Regards