[PATCH] pinctrl: mediatek: paris: Revert "Rework support for PIN_CONFIG_{INPUT,OUTPUT}_ENABLE"

[Bo Ye <bo.ye@mediatek.com>]

[This reverts commit c5d3b64c568a344e998830e0e94a7c04e372f89b.]

For MTK HW,
1. to enable GPIO input direction: set DIR=0, IES=1
2. to enable GPIO output direction: set DIR=1, and set DO=1 to output high, set DO=0 to out low

The PIN_CONFIG_INPUT/PIN_CONFIG_OUTPUT/PIN_CONFIG_INPUT_ENABLE/PIN_CONFIG_OUTPUT_ENABLE shall
be implemented according to view of its purpose - set GPIO direction and output value (for
output only) according to specific HW design.

However, the reverted patch implement according to author's own explanation of IES without
understanding of MTK's HW. Such patch does not correctly set DIR/IES bit to control GPIO
direction on MTK's HW.

Signed-off-by: Light Hsieh <light.hsieh@mediatek.com>
Signed-off-by: Evan Cao <ot_evan.cao@mediatek.com>
Signed-off-by: Bo Ye <bo.ye@mediatek.com>
---
 drivers/pinctrl/mediatek/pinctrl-paris.c | 38 +++++++++++++++++-------
 1 file changed, 27 insertions(+), 11 deletions(-)

diff --git a/drivers/pinctrl/mediatek/pinctrl-paris.c b/drivers/pinctrl/mediatek/pinctrl-paris.c
index 87e958d827bf..a8af62e6f8ca 100644
--- a/drivers/pinctrl/mediatek/pinctrl-paris.c
+++ b/drivers/pinctrl/mediatek/pinctrl-paris.c
@@ -165,21 +165,20 @@ static int mtk_pinconf_get(struct pinctrl_dev *pctldev,
 		err = mtk_hw_get_value(hw, desc, PINCTRL_PIN_REG_SR, &ret);
 		break;
 	case PIN_CONFIG_INPUT_ENABLE:
-		err = mtk_hw_get_value(hw, desc, PINCTRL_PIN_REG_IES, &ret);
-		if (!ret)
-			err = -EINVAL;
-		break;
-	case PIN_CONFIG_OUTPUT:
+	case PIN_CONFIG_OUTPUT_ENABLE:
 		err = mtk_hw_get_value(hw, desc, PINCTRL_PIN_REG_DIR, &ret);
 		if (err)
 			break;
+		/*     CONFIG     Current direction return value
+		 * -------------  ----------------- ----------------------
+		 * OUTPUT_ENABLE       output       1 (= HW value)
+		 *                     input        0 (= HW value)
+		 * INPUT_ENABLE        output       0 (= reverse HW value)
+		 *                     input        1 (= reverse HW value)
+		 */
+		if (param == PIN_CONFIG_INPUT_ENABLE)
+			ret = !ret;
 
-		if (!ret) {
-			err = -EINVAL;
-			break;
-		}
-
-		err = mtk_hw_get_value(hw, desc, PINCTRL_PIN_REG_DO, &ret);
 		break;
 	case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
 		err = mtk_hw_get_value(hw, desc, PINCTRL_PIN_REG_DIR, &ret);
@@ -284,9 +283,26 @@ static int mtk_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
 			break;
 		err = hw->soc->bias_set_combo(hw, desc, 0, arg);
 		break;
+	case PIN_CONFIG_OUTPUT_ENABLE:
+		err = mtk_hw_set_value(hw, desc, PINCTRL_PIN_REG_SMT,
+				       MTK_DISABLE);
+		/* Keep set direction to consider the case that a GPIO pin
+		 *  does not have SMT control
+		 */
+		if (err != -ENOTSUPP)
+			break;
+
+		err = mtk_hw_set_value(hw, desc, PINCTRL_PIN_REG_DIR,
+				       MTK_OUTPUT);
+		break;
 	case PIN_CONFIG_INPUT_ENABLE:
 		/* regard all non-zero value as enable */
 		err = mtk_hw_set_value(hw, desc, PINCTRL_PIN_REG_IES, !!arg);
+		if (err)
+			break;
+
+		err = mtk_hw_set_value(hw, desc, PINCTRL_PIN_REG_DIR,
+				       MTK_INPUT);
 		break;
 	case PIN_CONFIG_SLEW_RATE:
 		/* regard all non-zero value as enable */
-- 
2.17.0