[PATCH v2 0/7] PCI: mediatek-gen3: add power control support

[PATCH v2 0/7] PCI: mediatek-gen3: add power control support

[Chen-Yu Tsai]

Hi folks,

This is v2 of my MediaTek PCIe gen3 controller driver power control
support series.

The only change is the commit message for patch 3 was rewritten.
Jianjun Wang was dropped from the recipients as the email was
bouncing.

This series adds power control support to the MediaTek PCIe gen3
controller driver. This allows proper modeling of WiFi and NVMe
adapters in the device tree and control over their power supplies.

Patch 1 through 4 are cleanups and minor improvements to the driver.

Patch 5 adds power control support using the new pwrctrl API to the
PCIe controller driver.

Patch 6 adds the WiFi and BT power supplies for the MT8195 Cherry design.
This is actually a M.2 E-key slot, but support for that is still WIP [1].
And even with it merged, support for the USB side still needs to be
figured out.

We can either merge this as is for now, and do another conversion later,
or just keep this one out. However this is still an improvement over
the current device tree, in which the power for the slot is always on
using a pinctrl setting.

Patch 7 adds the M.2 M-key NVMe slot found on MT8195 Dojo Chromebooks.
This change actually makes use of the M.2 pwrseq driver.


Please have a look.


Thanks
ChenYu

[1] https://lore.kernel.org/linux-pci/20260224-pci-m2-e-v5-0-dd9b9501d33c@oss.qualcomm.com/

Chen-Yu Tsai (7):
  PCI: mediatek-gen3: Clean up mtk_pcie_parse_port() with
    dev_err_probe()
  PCI: mediatek-gen3: Add error path for probe and resume driver
    callbacks
  PCI: mediatek-gen3: Split out device power helpers
  PCI: mediatek-gen3: Disable device if further setup fails
  PCI: mediatek-gen3: Integrate new pwrctrl API
  arm64: dts: mediatek: mt8195-cherry: add WiFi PCIe and BT USB power
    supplies
  arm64: dts: mediatek: mt8195-cherry-dojo: Describe M.2 M-key NVMe slot

 .../dts/mediatek/mt8195-cherry-dojo-r1.dts    |  38 ++++
 .../boot/dts/mediatek/mt8195-cherry.dtsi      |  47 +++--
 drivers/pci/controller/pcie-mediatek-gen3.c   | 185 +++++++++++-------
 3 files changed, 183 insertions(+), 87 deletions(-)

-- 
2.53.0.414.gf7e9f6c205-goog

[PATCH v2 1/7] PCI: mediatek-gen3: Clean up mtk_pcie_parse_port() with dev_err_probe()

[Chen-Yu Tsai]

mtk_pcie_parse_port() in the pcie-mediatek-gen driver has a bunch of

    if (err) {
    	dev_err(dev, "error message\n");
	return err; # or goto
    }

patterns.

Simplify these with dev_err_probe(). The system also gains proper
deferred probe messages that can be seen in

    /sys/kernel/debug/devices_deferred

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
---
 drivers/pci/controller/pcie-mediatek-gen3.c | 36 ++++++---------------
 1 file changed, 10 insertions(+), 26 deletions(-)

diff --git a/drivers/pci/controller/pcie-mediatek-gen3.c b/drivers/pci/controller/pcie-mediatek-gen3.c
index 75ddb8bee168..1939cac995b5 100644
--- a/drivers/pci/controller/pcie-mediatek-gen3.c
+++ b/drivers/pci/controller/pcie-mediatek-gen3.c
@@ -876,10 +876,8 @@ static int mtk_pcie_parse_port(struct mtk_gen3_pcie *pcie)
 	if (!regs)
 		return -EINVAL;
 	pcie->base = devm_ioremap_resource(dev, regs);
-	if (IS_ERR(pcie->base)) {
-		dev_err(dev, "failed to map register base\n");
-		return PTR_ERR(pcie->base);
-	}
+	if (IS_ERR(pcie->base))
+		return dev_err_probe(dev, PTR_ERR(pcie->base), "failed to map register base\n");
 
 	pcie->reg_base = regs->start;
 
@@ -888,34 +886,20 @@ static int mtk_pcie_parse_port(struct mtk_gen3_pcie *pcie)
 
 	ret = devm_reset_control_bulk_get_optional_shared(dev, num_resets,
 							  pcie->phy_resets);
-	if (ret) {
-		dev_err(dev, "failed to get PHY bulk reset\n");
-		return ret;
-	}
+	if (ret)
+		return dev_err_probe(dev, ret, "failed to get PHY bulk reset\n");
 
 	pcie->mac_reset = devm_reset_control_get_optional_exclusive(dev, "mac");
-	if (IS_ERR(pcie->mac_reset)) {
-		ret = PTR_ERR(pcie->mac_reset);
-		if (ret != -EPROBE_DEFER)
-			dev_err(dev, "failed to get MAC reset\n");
-
-		return ret;
-	}
+	if (IS_ERR(pcie->mac_reset))
+		return dev_err_probe(dev, PTR_ERR(pcie->mac_reset), "failed to get MAC reset\n");
 
 	pcie->phy = devm_phy_optional_get(dev, "pcie-phy");
-	if (IS_ERR(pcie->phy)) {
-		ret = PTR_ERR(pcie->phy);
-		if (ret != -EPROBE_DEFER)
-			dev_err(dev, "failed to get PHY\n");
-
-		return ret;
-	}
+	if (IS_ERR(pcie->phy))
+		return dev_err_probe(dev, PTR_ERR(pcie->phy), "failed to get PHY\n");
 
 	pcie->num_clks = devm_clk_bulk_get_all(dev, &pcie->clks);
-	if (pcie->num_clks < 0) {
-		dev_err(dev, "failed to get clocks\n");
-		return pcie->num_clks;
-	}
+	if (pcie->num_clks < 0)
+		return dev_err_probe(dev, pcie->num_clks, "failed to get clocks\n");
 
 	ret = of_property_read_u32(dev->of_node, "num-lanes", &num_lanes);
 	if (ret == 0) {
-- 
2.53.0.414.gf7e9f6c205-goog

[PATCH v2 2/7] PCI: mediatek-gen3: Add error path for probe and resume driver callbacks

[Chen-Yu Tsai]

The probe and resume callbacks currently do teardown in the conditional
block directly. This is going to get ugly when the pwrctrl calls are
added.

Move the teardown to proper error cleanup paths.

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
---
 drivers/pci/controller/pcie-mediatek-gen3.c | 22 ++++++++++++---------
 1 file changed, 13 insertions(+), 9 deletions(-)

diff --git a/drivers/pci/controller/pcie-mediatek-gen3.c b/drivers/pci/controller/pcie-mediatek-gen3.c
index 1939cac995b5..f2bf4afbdc2f 100644
--- a/drivers/pci/controller/pcie-mediatek-gen3.c
+++ b/drivers/pci/controller/pcie-mediatek-gen3.c
@@ -1189,13 +1189,15 @@ static int mtk_pcie_probe(struct platform_device *pdev)
 	host->sysdata = pcie;
 
 	err = pci_host_probe(host);
-	if (err) {
-		mtk_pcie_irq_teardown(pcie);
-		mtk_pcie_power_down(pcie);
-		return err;
-	}
+	if (err)
+		goto err_teardown_irq_and_power_down;
 
 	return 0;
+
+err_teardown_irq_and_power_down:
+	mtk_pcie_irq_teardown(pcie);
+	mtk_pcie_power_down(pcie);
+	return err;
 }
 
 static void mtk_pcie_remove(struct platform_device *pdev)
@@ -1301,14 +1303,16 @@ static int mtk_pcie_resume_noirq(struct device *dev)
 		return err;
 
 	err = mtk_pcie_startup_port(pcie);
-	if (err) {
-		mtk_pcie_power_down(pcie);
-		return err;
-	}
+	if (err)
+		goto err_power_down;
 
 	mtk_pcie_irq_restore(pcie);
 
 	return 0;
+
+err_power_down:
+	mtk_pcie_power_down(pcie);
+	return err;
 }
 
 static const struct dev_pm_ops mtk_pcie_pm_ops = {
-- 
2.53.0.414.gf7e9f6c205-goog

[PATCH v2 3/7] PCI: mediatek-gen3: Split out device power helpers

[Chen-Yu Tsai]

In preparation for adding full power on/off control with the pwrctrl
API, split out the existing code that only partially deals with device
power sequencing into separate helper functions. The existing code only
handles PERST#.

This is purely moving code around, and brings no functional changes.

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
---
Changes since v1:
- Updated commit message
---
 drivers/pci/controller/pcie-mediatek-gen3.c | 87 ++++++++++++---------
 1 file changed, 52 insertions(+), 35 deletions(-)

diff --git a/drivers/pci/controller/pcie-mediatek-gen3.c b/drivers/pci/controller/pcie-mediatek-gen3.c
index f2bf4afbdc2f..870d3b3db11d 100644
--- a/drivers/pci/controller/pcie-mediatek-gen3.c
+++ b/drivers/pci/controller/pcie-mediatek-gen3.c
@@ -403,6 +403,54 @@ static void mtk_pcie_enable_msi(struct mtk_gen3_pcie *pcie)
 	writel_relaxed(val, pcie->base + PCIE_INT_ENABLE_REG);
 }
 
+static int mtk_pcie_device_power_up(struct mtk_gen3_pcie *pcie)
+{
+	int err;
+	u32 val;
+
+	/*
+	 * Airoha EN7581 has a hw bug asserting/releasing PCIE_PE_RSTB signal
+	 * causing occasional PCIe link down. In order to overcome the issue,
+	 * PCIE_RSTB signals are not asserted/released at this stage and the
+	 * PCIe block is reset using en7523_reset_assert() and
+	 * en7581_pci_enable().
+	 */
+	if (!(pcie->soc->flags & SKIP_PCIE_RSTB)) {
+		/* Assert all reset signals */
+		val = readl_relaxed(pcie->base + PCIE_RST_CTRL_REG);
+		val |= PCIE_MAC_RSTB | PCIE_PHY_RSTB | PCIE_BRG_RSTB |
+		       PCIE_PE_RSTB;
+		writel_relaxed(val, pcie->base + PCIE_RST_CTRL_REG);
+
+		/*
+		 * Described in PCIe CEM specification revision 6.0.
+		 *
+		 * The deassertion of PERST# should be delayed 100ms (TPVPERL)
+		 * for the power and clock to become stable.
+		 */
+		msleep(PCIE_T_PVPERL_MS);
+
+		/* De-assert reset signals */
+		val &= ~(PCIE_MAC_RSTB | PCIE_PHY_RSTB | PCIE_BRG_RSTB |
+			 PCIE_PE_RSTB);
+		writel_relaxed(val, pcie->base + PCIE_RST_CTRL_REG);
+	}
+
+	return 0;
+}
+
+static void mtk_pcie_device_power_down(struct mtk_gen3_pcie *pcie)
+{
+	u32 val;
+
+	if (!(pcie->soc->flags & SKIP_PCIE_RSTB)) {
+		/* Assert the PERST# pin */
+		val = readl_relaxed(pcie->base + PCIE_RST_CTRL_REG);
+		val |= PCIE_PE_RSTB;
+		writel_relaxed(val, pcie->base + PCIE_RST_CTRL_REG);
+	}
+}
+
 static int mtk_pcie_startup_port(struct mtk_gen3_pcie *pcie)
 {
 	struct resource_entry *entry;
@@ -464,33 +512,9 @@ static int mtk_pcie_startup_port(struct mtk_gen3_pcie *pcie)
 	val |= PCIE_DISABLE_DVFSRC_VLT_REQ;
 	writel_relaxed(val, pcie->base + PCIE_MISC_CTRL_REG);
 
-	/*
-	 * Airoha EN7581 has a hw bug asserting/releasing PCIE_PE_RSTB signal
-	 * causing occasional PCIe link down. In order to overcome the issue,
-	 * PCIE_RSTB signals are not asserted/released at this stage and the
-	 * PCIe block is reset using en7523_reset_assert() and
-	 * en7581_pci_enable().
-	 */
-	if (!(pcie->soc->flags & SKIP_PCIE_RSTB)) {
-		/* Assert all reset signals */
-		val = readl_relaxed(pcie->base + PCIE_RST_CTRL_REG);
-		val |= PCIE_MAC_RSTB | PCIE_PHY_RSTB | PCIE_BRG_RSTB |
-		       PCIE_PE_RSTB;
-		writel_relaxed(val, pcie->base + PCIE_RST_CTRL_REG);
-
-		/*
-		 * Described in PCIe CEM specification revision 6.0.
-		 *
-		 * The deassertion of PERST# should be delayed 100ms (TPVPERL)
-		 * for the power and clock to become stable.
-		 */
-		msleep(PCIE_T_PVPERL_MS);
-
-		/* De-assert reset signals */
-		val &= ~(PCIE_MAC_RSTB | PCIE_PHY_RSTB | PCIE_BRG_RSTB |
-			 PCIE_PE_RSTB);
-		writel_relaxed(val, pcie->base + PCIE_RST_CTRL_REG);
-	}
+	err = mtk_pcie_device_power_up(pcie);
+	if (err)
+		return err;
 
 	/* Check if the link is up or not */
 	err = readl_poll_timeout(pcie->base + PCIE_LINK_STATUS_REG, val,
@@ -1269,7 +1293,6 @@ static int mtk_pcie_suspend_noirq(struct device *dev)
 {
 	struct mtk_gen3_pcie *pcie = dev_get_drvdata(dev);
 	int err;
-	u32 val;
 
 	/* Trigger link to L2 state */
 	err = mtk_pcie_turn_off_link(pcie);
@@ -1278,13 +1301,7 @@ static int mtk_pcie_suspend_noirq(struct device *dev)
 		return err;
 	}
 
-	if (!(pcie->soc->flags & SKIP_PCIE_RSTB)) {
-		/* Assert the PERST# pin */
-		val = readl_relaxed(pcie->base + PCIE_RST_CTRL_REG);
-		val |= PCIE_PE_RSTB;
-		writel_relaxed(val, pcie->base + PCIE_RST_CTRL_REG);
-	}
-
+	mtk_pcie_device_power_down(pcie);
 	dev_dbg(pcie->dev, "entered L2 states successfully");
 
 	mtk_pcie_irq_save(pcie);
-- 
2.53.0.414.gf7e9f6c205-goog

[PATCH v2 4/7] PCI: mediatek-gen3: Disable device if further setup fails

[Chen-Yu Tsai]

If further setup fails after the device is powered on and link training
succeeds, we want to place the device back in a quiescence state to
avoid unintended activity and save power. This also helps with power
state tracking and balancing once pwrctrl API is integrated.

Power down the device in the error paths of mtk_pcie_startup_port() and
mtk_pcie_setup().

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
---
 drivers/pci/controller/pcie-mediatek-gen3.c | 16 +++++++++++-----
 1 file changed, 11 insertions(+), 5 deletions(-)

diff --git a/drivers/pci/controller/pcie-mediatek-gen3.c b/drivers/pci/controller/pcie-mediatek-gen3.c
index 870d3b3db11d..7459e1c1899d 100644
--- a/drivers/pci/controller/pcie-mediatek-gen3.c
+++ b/drivers/pci/controller/pcie-mediatek-gen3.c
@@ -531,7 +531,7 @@ static int mtk_pcie_startup_port(struct mtk_gen3_pcie *pcie)
 		dev_err(pcie->dev,
 			"PCIe link down, current LTSSM state: %s (%#x)\n",
 			ltssm_state, val);
-		return err;
+		goto err_power_down_device;
 	}
 
 	mtk_pcie_enable_msi(pcie);
@@ -556,10 +556,14 @@ static int mtk_pcie_startup_port(struct mtk_gen3_pcie *pcie)
 		err = mtk_pcie_set_trans_table(pcie, cpu_addr, pci_addr, size,
 					       type, &table_index);
 		if (err)
-			return err;
+			goto err_power_down_device;
 	}
 
 	return 0;
+
+err_power_down_device:
+	mtk_pcie_device_power_down(pcie);
+	return err;
 }
 
 #define MTK_MSI_FLAGS_REQUIRED (MSI_FLAG_USE_DEF_DOM_OPS	| \
@@ -1174,15 +1178,17 @@ static int mtk_pcie_setup(struct mtk_gen3_pcie *pcie)
 	/* Try link up */
 	err = mtk_pcie_startup_port(pcie);
 	if (err)
-		goto err_setup;
+		goto err_power_down;
 
 	err = mtk_pcie_setup_irq(pcie);
 	if (err)
-		goto err_setup;
+		goto err_device_power_off;
 
 	return 0;
 
-err_setup:
+err_device_power_off:
+	mtk_pcie_device_power_down(pcie);
+err_power_down:
 	mtk_pcie_power_down(pcie);
 
 	return err;
-- 
2.53.0.414.gf7e9f6c205-goog

[PATCH v2 5/7] PCI: mediatek-gen3: Integrate new pwrctrl API

[Chen-Yu Tsai]

With the new PCI pwrctrl API and PCI slot binding and power drivers, we
now have a way to describe and power up WiFi/BT adapters connected
through a PCIe or M.2 slot, or exploded onto the mainboard itself.

Integrate the PCI pwrctrl API into the PCIe driver, so that power is
properly enabled before PCIe link training is done, allowing the
card to successfully be detected.

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
---
 drivers/pci/controller/pcie-mediatek-gen3.c | 38 ++++++++++++++++-----
 1 file changed, 30 insertions(+), 8 deletions(-)

diff --git a/drivers/pci/controller/pcie-mediatek-gen3.c b/drivers/pci/controller/pcie-mediatek-gen3.c
index 7459e1c1899d..93e591f788f7 100644
--- a/drivers/pci/controller/pcie-mediatek-gen3.c
+++ b/drivers/pci/controller/pcie-mediatek-gen3.c
@@ -22,6 +22,7 @@
 #include <linux/of_device.h>
 #include <linux/of_pci.h>
 #include <linux/pci.h>
+#include <linux/pci-pwrctrl.h>
 #include <linux/phy/phy.h>
 #include <linux/platform_device.h>
 #include <linux/pm_domain.h>
@@ -421,15 +422,23 @@ static int mtk_pcie_device_power_up(struct mtk_gen3_pcie *pcie)
 		val |= PCIE_MAC_RSTB | PCIE_PHY_RSTB | PCIE_BRG_RSTB |
 		       PCIE_PE_RSTB;
 		writel_relaxed(val, pcie->base + PCIE_RST_CTRL_REG);
+	}
+
+	err = pci_pwrctrl_power_on_devices(pcie->dev);
+	if (err) {
+		dev_err(pcie->dev, "Failed to power on devices: %pe\n", ERR_PTR(err));
+		return err;
+	}
 
-		/*
-		 * Described in PCIe CEM specification revision 6.0.
-		 *
-		 * The deassertion of PERST# should be delayed 100ms (TPVPERL)
-		 * for the power and clock to become stable.
-		 */
-		msleep(PCIE_T_PVPERL_MS);
+	/*
+	 * Described in PCIe CEM specification revision 6.0.
+	 *
+	 * The deassertion of PERST# should be delayed 100ms (TPVPERL)
+	 * for the power and clock to become stable.
+	 */
+	msleep(PCIE_T_PVPERL_MS);
 
+	if (!(pcie->soc->flags & SKIP_PCIE_RSTB)) {
 		/* De-assert reset signals */
 		val &= ~(PCIE_MAC_RSTB | PCIE_PHY_RSTB | PCIE_BRG_RSTB |
 			 PCIE_PE_RSTB);
@@ -449,6 +458,8 @@ static void mtk_pcie_device_power_down(struct mtk_gen3_pcie *pcie)
 		val |= PCIE_PE_RSTB;
 		writel_relaxed(val, pcie->base + PCIE_RST_CTRL_REG);
 	}
+
+	pci_pwrctrl_power_off_devices(pcie->dev);
 }
 
 static int mtk_pcie_startup_port(struct mtk_gen3_pcie *pcie)
@@ -1211,9 +1222,13 @@ static int mtk_pcie_probe(struct platform_device *pdev)
 	pcie->soc = device_get_match_data(dev);
 	platform_set_drvdata(pdev, pcie);
 
+	err = pci_pwrctrl_create_devices(pcie->dev);
+	if (err)
+		return dev_err_probe(dev, err, "failed to create pwrctrl devices\n");
+
 	err = mtk_pcie_setup(pcie);
 	if (err)
-		return err;
+		goto err_destroy_pwrctrl;
 
 	host->ops = &mtk_pcie_ops;
 	host->sysdata = pcie;
@@ -1226,7 +1241,12 @@ static int mtk_pcie_probe(struct platform_device *pdev)
 
 err_teardown_irq_and_power_down:
 	mtk_pcie_irq_teardown(pcie);
+	mtk_pcie_device_power_down(pcie);
 	mtk_pcie_power_down(pcie);
+err_destroy_pwrctrl:
+	if (err != -EPROBE_DEFER)
+		pci_pwrctrl_destroy_devices(pcie->dev);
+
 	return err;
 }
 
@@ -1241,7 +1261,9 @@ static void mtk_pcie_remove(struct platform_device *pdev)
 	pci_unlock_rescan_remove();
 
 	mtk_pcie_irq_teardown(pcie);
+	pci_pwrctrl_power_off_devices(pcie->dev);
 	mtk_pcie_power_down(pcie);
+	pci_pwrctrl_destroy_devices(pcie->dev);
 }
 
 static void mtk_pcie_irq_save(struct mtk_gen3_pcie *pcie)
-- 
2.53.0.414.gf7e9f6c205-goog

[PATCH v2 6/7] arm64: dts: mediatek: mt8195-cherry: add WiFi PCIe and BT USB power supplies

[Chen-Yu Tsai]

The MT8195 Cherry design features an M.2 E-key slot wired up with PCIe
and USB for a WiFi+BT adapter. Previously the power was just enabled
all the time with a default pinctrl setting that set the GPIO pin high.

With the PCIe slot description DT binding in place, the power supplies
can at least be added and tied to the PCIe and USB hosts. Once the
M.2 E-key binding is merged, this description can be further converted
to an M.2 E-key.

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
---
 .../boot/dts/mediatek/mt8195-cherry.dtsi      | 47 ++++++++++++++-----
 1 file changed, 36 insertions(+), 11 deletions(-)

diff --git a/arch/arm64/boot/dts/mediatek/mt8195-cherry.dtsi b/arch/arm64/boot/dts/mediatek/mt8195-cherry.dtsi
index 6e99122c65ac..f1ff64a84267 100644
--- a/arch/arm64/boot/dts/mediatek/mt8195-cherry.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8195-cherry.dtsi
@@ -83,6 +83,17 @@ pp3300_s3: regulator-pp3300-s3 {
 		vin-supply = <&pp3300_z2>;
 	};
 
+	pp3300_wlan: regulator-pp3300-wlan {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pp3300_wlan_en_pin>;
+		regulator-name = "pp3300_wlan";
+		/* load switch */
+		enable-active-high;
+		gpio = <&pio 58 GPIO_ACTIVE_HIGH>;
+		vin-supply = <&pp3300_z2>;
+	};
+
 	/* system wide 3.3V power rail */
 	pp3300_z2: regulator-pp3300-z2 {
 		compatible = "regulator-fixed";
@@ -760,10 +771,25 @@ &ovl0_in {
 };
 
 &pcie1 {
-	status = "okay";
-
 	pinctrl-names = "default";
 	pinctrl-0 = <&pcie1_pins_default>;
+	status = "okay";
+
+	pcie@0 {
+		compatible = "pciclass,0604";
+		reg = <0 0 0 0 0>;
+		device_type = "pci";
+		num-lanes = <1>;
+		vpcie3v3-supply = <&pp3300_wlan>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		ranges;
+
+		wifi@0 {
+			reg = <0 0 0 0 0>;
+			wakeup-source;
+		};
+	};
 };
 
 &pio {
@@ -1179,12 +1205,6 @@ pins-vreg-en {
 	};
 
 	pio_default: pio-default-pins {
-		pins-wifi-enable {
-			pinmux = <PINMUX_GPIO58__FUNC_GPIO58>;
-			output-high;
-			drive-strength = <14>;
-		};
-
 		pins-low-power-pd {
 			pinmux = <PINMUX_GPIO25__FUNC_GPIO25>,
 				 <PINMUX_GPIO26__FUNC_GPIO26>,
@@ -1222,6 +1242,12 @@ pins-low-power-pupd {
 		};
 	};
 
+	pp3300_wlan_en_pin: pp3300-wlan-en-pins {
+		pins-en {
+			pinmux = <PINMUX_GPIO58__FUNC_GPIO58>;
+		};
+	};
+
 	rt1019p_pins_default: rt1019p-default-pins {
 		pins-amp-sdb {
 			pinmux = <PINMUX_GPIO100__FUNC_GPIO100>;
@@ -1570,11 +1596,10 @@ &xhci2 {
 };
 
 &xhci3 {
-	status = "okay";
-
 	/* MT7921's USB Bluetooth has issues with USB2 LPM */
 	usb2-lpm-disable;
-	vbus-supply = <&usb_vbus>;
+	vbus-supply = <&pp3300_wlan>;
+	status = "okay";
 };
 
 #include <arm/cros-ec-keyboard.dtsi>
-- 
2.53.0.414.gf7e9f6c205-goog

[PATCH v2 7/7] arm64: dts: mediatek: mt8195-cherry-dojo: Describe M.2 M-key NVMe slot

[Chen-Yu Tsai]

The Dojo device has a M.2 M-key slot for an included NVMe on some
models.

Add a proper device tree description based on the new M.2 M-key binding.
Power for the slot is controlled by the embedded controller. As far as
the main SoC is concerned, it is always on.

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
---
 .../dts/mediatek/mt8195-cherry-dojo-r1.dts    | 38 +++++++++++++++++++
 1 file changed, 38 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt8195-cherry-dojo-r1.dts b/arch/arm64/boot/dts/mediatek/mt8195-cherry-dojo-r1.dts
index 49664de99b88..57cc329f49c4 100644
--- a/arch/arm64/boot/dts/mediatek/mt8195-cherry-dojo-r1.dts
+++ b/arch/arm64/boot/dts/mediatek/mt8195-cherry-dojo-r1.dts
@@ -11,6 +11,28 @@ / {
 	compatible = "google,dojo-sku7", "google,dojo-sku5",
 		     "google,dojo-sku3", "google,dojo-sku1",
 		     "google,dojo", "mediatek,mt8195";
+
+	nvme-connector {
+		compatible = "pcie-m2-m-connector";
+		/* power is controlled by EC */
+		vpcie3v3-supply = <&pp3300_z2>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				nvme_ep: endpoint@0 {
+					reg = <0>;
+					remote-endpoint = <&pcie0_ep>;
+				};
+			};
+		};
+	};
 };
 
 &audio_codec {
@@ -72,6 +94,22 @@ &pcie0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pcie0_pins_default>;
 	status = "okay";
+
+	pcie@0 {
+		compatible = "pciclass,0604";
+		reg = <0 0 0 0 0>;
+		device_type = "pci";
+		num-lanes = <2>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		ranges;
+
+		port {
+			pcie0_ep: endpoint {
+				remote-endpoint = <&nvme_ep>;
+			};
+		};
+	};
 };
 
 &pciephy {
-- 
2.53.0.414.gf7e9f6c205-goog

Re: [PATCH v2 5/7] PCI: mediatek-gen3: Integrate new pwrctrl API

[kernel test robot]

Hi Chen-Yu,

kernel test robot noticed the following build errors:

[auto build test ERROR on pci/next]
[also build test ERROR on pci/for-linus robh/for-next linus/master v7.0-rc1 next-20260227]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch#_base_tree_information]

url:    https://github.com/intel-lab-lkp/linux/commits/Chen-Yu-Tsai/PCI-mediatek-gen3-Clean-up-mtk_pcie_parse_port-with-dev_err_probe/20260226-155647
base:   https://git.kernel.org/pub/scm/linux/kernel/git/pci/pci.git next
patch link:    https://lore.kernel.org/r/20260226074524.3808081-6-wenst%40chromium.org
patch subject: [PATCH v2 5/7] PCI: mediatek-gen3: Integrate new pwrctrl API
config: um-randconfig-001-20260227 (https://download.01.org/0day-ci/archive/20260228/202602280453.4TGe7q2R-lkp@intel.com/config)
compiler: clang version 23.0.0git (https://github.com/llvm/llvm-project 9a109fbb6e184ec9bcce10615949f598f4c974a9)
reproduce (this is a W=1 build): (https://download.01.org/0day-ci/archive/20260228/202602280453.4TGe7q2R-lkp@intel.com/reproduce)

If you fix the issue in a separate patch/commit (i.e. not just a new version of
the same patch/commit), kindly add following tags
| Reported-by: kernel test robot <lkp@intel.com>
| Closes: https://lore.kernel.org/oe-kbuild-all/202602280453.4TGe7q2R-lkp@intel.com/

All errors (new ones prefixed by >>):

   /usr/bin/ld: warning: .tmp_vmlinux1 has a LOAD segment with RWX permissions
   /usr/bin/ld: drivers/pci/controller/pcie-mediatek-gen3.o: in function `mtk_pcie_probe':
>> pcie-mediatek-gen3.c:(.ltext+0x7e5): undefined reference to `pci_pwrctrl_create_devices'
>> /usr/bin/ld: pcie-mediatek-gen3.c:(.ltext+0xd45): undefined reference to `pci_pwrctrl_destroy_devices'
   /usr/bin/ld: drivers/pci/controller/pcie-mediatek-gen3.o: in function `mtk_pcie_remove':
>> pcie-mediatek-gen3.c:(.ltext+0xefd): undefined reference to `pci_pwrctrl_power_off_devices'
   /usr/bin/ld: pcie-mediatek-gen3.c:(.ltext+0xff0): undefined reference to `pci_pwrctrl_destroy_devices'
   /usr/bin/ld: drivers/pci/controller/pcie-mediatek-gen3.o: in function `mtk_pcie_device_power_down':
   pcie-mediatek-gen3.c:(.ltext+0x10cb): undefined reference to `pci_pwrctrl_power_off_devices'
   /usr/bin/ld: drivers/pci/controller/pcie-mediatek-gen3.o: in function `mtk_pcie_startup_port':
>> pcie-mediatek-gen3.c:(.ltext+0x13f6): undefined reference to `pci_pwrctrl_power_on_devices'
>> /usr/bin/ld: pcie-mediatek-gen3.c:(.ltext+0x1ae1): undefined reference to `pci_pwrctrl_power_off_devices'
   /usr/bin/ld: drivers/pci/controller/pcie-mediatek-gen3.o: in function `mtk_pcie_suspend_noirq':
   pcie-mediatek-gen3.c:(.ltext+0x1d19): undefined reference to `pci_pwrctrl_power_off_devices'
   clang: error: linker command failed with exit code 1 (use -v to see invocation)

-- 
0-DAY CI Kernel Test Service
https://github.com/intel/lkp-tests/wiki