[PATCH 1/2] arm64: dts: mediatek: mt8390-genio-common: Fix type C port mode and connection

[Chen-Yu Tsai <wenst@chromium.org>]

The USB controller complex ssusb1 and xhci1 operate in host mode only,
as it is immediately connected to a USB hub. The user manual has a block
diagram showing this, and a USB usage table showing port 1 as "host
only".

Change the controller's operating mode to "host", and drop the USB role
switch property. Fix the USB type C port data line connections to go
through the USB hub, as shown in the block diagram. Change the data-role
on the type C port to "host".

Fixes: 1afaeca17238 ("arm64: dts: mediatek: mt8390-genio-700: Add USB, TypeC Controller, MUX")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
---
Compile tested only.

Unfortunately I don't have a board or the schematics to check which of
the USB hub downstream ports the type C port is connected to.

Also, the order of the USB hubs might be reversed. In my previous
experience, port 1 on the XHCI is SuperSpeed, and port 2 is HighSpeed.
---
 .../dts/mediatek/mt8390-genio-common.dtsi     | 43 ++++++++++++-------
 1 file changed, 28 insertions(+), 15 deletions(-)

diff --git a/arch/arm64/boot/dts/mediatek/mt8390-genio-common.dtsi b/arch/arm64/boot/dts/mediatek/mt8390-genio-common.dtsi
index 669eaec662f3..821dbf9d3fc5 100644
--- a/arch/arm64/boot/dts/mediatek/mt8390-genio-common.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8390-genio-common.dtsi
@@ -512,7 +512,7 @@ rt1715@4e {
 		connector {
 			compatible = "usb-c-connector";
 			label = "USB-C";
-			data-role = "dual";
+			data-role = "host";
 			op-sink-microwatt = <10000000>;
 			power-role = "dual";
 			try-power-role  = "sink";
@@ -539,14 +539,14 @@ ports {
 				port@0 {
 					reg = <0>;
 					typec_con_hs: endpoint {
-						remote-endpoint = <&mtu3_hs1_role_sw>;
+						remote-endpoint = <&usb_2_0_p2>;
 					};
 				};
 
 				port@1 {
 					reg = <1>;
 					typec_con_ss: endpoint {
-						remote-endpoint = <&xhci_ss_ep>;
+						remote-endpoint = <&usb_3_0_p2>;
 					};
 				};
 
@@ -1528,19 +1528,12 @@ &xhci0 {
 };
 
 &ssusb1 {
-	dr_mode = "otg";
-	usb-role-switch;
+	dr_mode = "host";
 	wakeup-source;
 	vusb33-supply = <&mt6359_vusb_ldo_reg>;
 	pinctrl-0 = <&usb1_default_pins>;
 	pinctrl-names = "default";
 	status = "okay";
-
-	port {
-		mtu3_hs1_role_sw: endpoint {
-			remote-endpoint = <&typec_con_hs>;
-		};
-	};
 };
 
 &xhci1 {
@@ -1555,6 +1548,19 @@ hub_2_0: hub@1 {
 		peer-hub = <&hub_3_0>;
 		reset-gpios = <&pio 7 GPIO_ACTIVE_HIGH>;
 		vdd-supply = <&usb_hub_fixed_3v3>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@2 {
+				reg = <2>;
+
+				usb_2_0_p2: endpoint {
+					remote-endpoint = <&typec_con_hs>;
+				};
+			};
+		};
 	};
 
 	hub_3_0: hub@2 {
@@ -1563,11 +1569,18 @@ hub_3_0: hub@2 {
 		peer-hub = <&hub_2_0>;
 		reset-gpios = <&pio 7 GPIO_ACTIVE_HIGH>;
 		vdd-supply = <&usb_hub_fixed_3v3>;
-	};
 
-	port {
-		xhci_ss_ep: endpoint {
-			remote-endpoint = <&typec_con_ss>;
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@2 {
+				reg = <2>;
+
+				usb_3_0_p2: endpoint {
+					remote-endpoint = <&typec_con_ss>;
+				};
+			};
 		};
 	};
 };
-- 
2.56.0.385.gac671c819a-goog