From: Daniel Golle <daniel@makrotopia.org>
To: Simon Horman <horms@kernel.org>
Cc: Felix Fietkau <nbd@nbd.name>, John Crispin <john@phrozen.org>,
Sean Wang <sean.wang@mediatek.com>,
Mark Lee <Mark-MC.Lee@mediatek.com>,
Lorenzo Bianconi <lorenzo@kernel.org>,
"David S. Miller" <davem@davemloft.net>,
Eric Dumazet <edumazet@google.com>,
Jakub Kicinski <kuba@kernel.org>, Paolo Abeni <pabeni@redhat.com>,
Matthias Brugger <matthias.bgg@gmail.com>,
AngeloGioacchino Del Regno
<angelogioacchino.delregno@collabora.com>,
Russell King <linux@armlinux.org.uk>,
linux-kernel@vger.kernel.org, netdev@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-mediatek@lists.infradead.org
Subject: Re: [PATCH RFC net-next v2] net: ethernet: mtk_eth_soc: add paths and SerDes modes for MT7988
Date: Sun, 27 Aug 2023 17:09:02 +0100 [thread overview]
Message-ID: <ZOt1Hp7v1tKRNGgX@makrotopia.org> (raw)
In-Reply-To: <20230827153523.GS3523530@kernel.org>
Hi Simon,
thank you for reviewing!
On Sun, Aug 27, 2023 at 05:35:23PM +0200, Simon Horman wrote:
> On Thu, Aug 24, 2023 at 09:24:48PM +0100, Daniel Golle wrote:
> > MT7988 comes with a built-in 2.5G PHY as well as SerDes lanes to
> > connect external PHYs or transceivers in USXGMII, 10GBase-R, 5GBase-R,
> > 2500Base-X, 1000Base-X and Cisco SGMII interface modes.
> >
> > Implement support for configuring for the new paths to SerDes interfaces
> > and the internal 2.5G PHY.
> >
> > Add USXGMII PCS driver for 10GBase-R, 5GBase-R and USXGMII mode, and
> > setup the new PHYA on MT7988 to access the also still existing old
> > LynxI PCS for 1000Base-X, 2500Base-X and Cisco SGMII PCS interface
> > modes.
> >
> > Signed-off-by: Daniel Golle <daniel@makrotopia.org>
>
> Hi Daniel,
>
> some minor feedback from my side.
>
> ...
>
> > diff --git a/drivers/net/ethernet/mediatek/mtk_usxgmii.c b/drivers/net/ethernet/mediatek/mtk_usxgmii.c
>
> ...
>
> > +static int mtk_usxgmii_pcs_config(struct phylink_pcs *pcs, unsigned int neg_mode,
> > + phy_interface_t interface,
> > + const unsigned long *advertising,
> > + bool permit_pause_to_mac)
> > +{
> > + struct mtk_usxgmii_pcs *mpcs = pcs_to_mtk_usxgmii_pcs(pcs);
> > + struct mtk_eth *eth = mpcs->eth;
> > + struct regmap *pextp = eth->regmap_pextp[mpcs->id];
> > + unsigned int an_ctrl = 0, link_timer = 0, xfi_mode = 0, adapt_mode = 0;
> > + bool mode_changed = false;
> > +
> > + if (!pextp)
> > + return -ENODEV;
> > +
> > + if (interface == PHY_INTERFACE_MODE_USXGMII) {
> > + an_ctrl = FIELD_PREP(USXGMII_AN_SYNC_CNT, 0x1FF) |
> > + (neg_mode == PHYLINK_PCS_NEG_INBAND_ENABLED) ?
> > + USXGMII_AN_ENABLE : 0;
>
> clang-16 W=1 suggests using parentheses here:
>
> drivers/net/ethernet/mediatek/mtk_usxgmii.c:468:51: warning: operator '?:' has lower precedence than '|'; '|' will be evaluated first [-Wbitwise-conditional-parentheses]
> (neg_mode == PHYLINK_PCS_NEG_INBAND_ENABLED) ?
> ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ^
> drivers/net/ethernet/mediatek/mtk_usxgmii.c:468:51: note: place parentheses around the '|' expression to silence this warning
> (neg_mode == PHYLINK_PCS_NEG_INBAND_ENABLED) ?
> ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ^
> drivers/net/ethernet/mediatek/mtk_usxgmii.c:468:51: note: place parentheses around the '?:' expression to evaluate it first
> (neg_mode == PHYLINK_PCS_NEG_INBAND_ENABLED) ?
> ^
> (
Yeah, I've seen that one coming up on patchwork as well, fixed it already in my
local tree.
>
> > + link_timer = FIELD_PREP(USXGMII_LINK_TIMER_IDLE_DETECT, 0x7B) |
> > + FIELD_PREP(USXGMII_LINK_TIMER_COMP_ACK_DETECT, 0x7B) |
> > + FIELD_PREP(USXGMII_LINK_TIMER_AN_RESTART, 0x7B);
> > + xfi_mode = FIELD_PREP(USXGMII_XFI_RX_MODE, USXGMII_XFI_RX_MODE_10G) |
> > + FIELD_PREP(USXGMII_XFI_TX_MODE, USXGMII_XFI_TX_MODE_10G);
>
> ...
>
> > +int mtk_usxgmii_init(struct mtk_eth *eth)
> > +{
> > + struct device_node *r = eth->dev->of_node;
> > + struct device *dev = eth->dev;
> > + struct device_node *np;
> > + int i, ret;
> > +
> > + for (i = 0; i < MTK_MAX_DEVS; i++) {
> > + np = of_parse_phandle(r, "mediatek,usxgmiisys", i);
> > + if (!np)
> > + break;
> > +
> > + eth->usxgmii_pcs[i] = devm_kzalloc(dev, sizeof(*eth->usxgmii_pcs), GFP_KERNEL);
>
> Smatch warns that only 8 bytes are allocated, whereas 64 are needed.
> I think one more defference of the parameter to sizeof().
>
> e.g.:
>
> eth->usxgmii_pcs[i] = devm_kzalloc(dev,
> sizeof(*eth->usxgmii_pcs[i]),
> GFP_KERNEL);
Good catch, thank you! I will fix it.
>
> > + if (!eth->usxgmii_pcs[i])
> > + return -ENOMEM;
> > +
> > + eth->usxgmii_pcs[i]->id = i;
> > + eth->usxgmii_pcs[i]->eth = eth;
> > + eth->usxgmii_pcs[i]->regmap = syscon_node_to_regmap(np);
> > + if (IS_ERR(eth->usxgmii_pcs[i]->regmap))
> > + return PTR_ERR(eth->usxgmii_pcs[i]->regmap);
> > +
> > + eth->usxgmii_pcs[i]->pcs.ops = &mtk_usxgmii_pcs_ops;
> > + eth->usxgmii_pcs[i]->pcs.poll = true;
> > + eth->usxgmii_pcs[i]->pcs.neg_mode = true;
> > + eth->usxgmii_pcs[i]->interface = PHY_INTERFACE_MODE_NA;
> > + eth->usxgmii_pcs[i]->neg_mode = -1;
> > +
> > + of_node_put(np);
> > + }
>
> ...
>
prev parent reply other threads:[~2023-08-27 16:09 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-08-24 20:24 [PATCH RFC net-next v2] net: ethernet: mtk_eth_soc: add paths and SerDes modes for MT7988 Daniel Golle
2023-08-27 15:35 ` Simon Horman
2023-08-27 16:09 ` Daniel Golle [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=ZOt1Hp7v1tKRNGgX@makrotopia.org \
--to=daniel@makrotopia.org \
--cc=Mark-MC.Lee@mediatek.com \
--cc=angelogioacchino.delregno@collabora.com \
--cc=davem@davemloft.net \
--cc=edumazet@google.com \
--cc=horms@kernel.org \
--cc=john@phrozen.org \
--cc=kuba@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mediatek@lists.infradead.org \
--cc=linux@armlinux.org.uk \
--cc=lorenzo@kernel.org \
--cc=matthias.bgg@gmail.com \
--cc=nbd@nbd.name \
--cc=netdev@vger.kernel.org \
--cc=pabeni@redhat.com \
--cc=sean.wang@mediatek.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox