From: Pete Popov <ppopov@embeddedalley.com>
To: rolf liu <rolfliu@gmail.com>
Cc: "linux-mips@linux-mips.org" <linux-mips@linux-mips.org>
Subject: Re: booting error on db1550 using linux 2.6.12 from linux-mips.org
Date: Wed, 06 Jul 2005 00:12:14 -0700 [thread overview]
Message-ID: <1120633934.5724.29.camel@localhost.localdomain> (raw)
In-Reply-To: <2db32b7205070508504b675dd6@mail.gmail.com>
On Tue, 2005-07-05 at 08:50 -0700, rolf liu wrote:
> Pete,
> I tried to make HPT working on db1550 for linux 2.6.12 cvs head. If I
> didn't force it to use 372 timing, it just hangs up after it detect
> the drive. If I used the 372 timing using the 2.4 trick, the kernel
> just crashed. Any clue?
Other than the call trace you can see below, no, no clues. I would have
to spend some time debugging it and if it ever becomes a priority, I
will.
Pete
> Thanks
>
> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> HPT371: IDE controller at PCI slot 0000:00:0b.0
> PCI: Enabling device 0000:00:0b.0 (0000 -> 0003)
> HPT371: chipset revision 2
> hpt: HPT372N detected, using 372N timing.
> FREQ: 73 PLL: 35
> HPT371: 100% native mode on irq 5
> hpt: no known IDE timings, disabling DMA.
> hpt: no known IDE timings, disabling DMA.
> hdg: IBM-DTTA-350840, ATA DISK drive
> CPU 0 Unable to handle kernel paging request at virtual address
> 00000000, epc == 8029fb20, ra == 8029fc0c
> Oops in arch/mips/mm/fault.c::do_page_fault, line 167[#1]:
> Cpu 0
> $ 0 : 00000000 1000fc00 00000000 00000000
> $ 4 : 0000000c 00000000 00010000 18010017
> $ 8 : 00000000 0000fc00 00000000 803a6000
> $12 : 803ace64 fffffffb ffffffff 0000140d
> $16 : 00000048 00000055 30070000 00000001
> $20 : 804a1800 0000000c 8043a678 8043a5f8
> $24 : 00000000 802a747c
> $28 : 811de000 811dfe40 1000fc01 8029fc0c
> Hi : 0000018a
> Lo : 3d6edc00
> epc : 8029fb20 pci_bus_clock_list+0x0/0x38 Not tainted
> ra : 8029fc0c hpt372_tune_chipset+0xb4/0x138
> Status: 1000fc03 KERNEL EXL IE
> Cause : 00800008
> BadVA : 00000000
> PrId : 03030200
> Modules linked in:
> Process swapper (pid: 1, threadinfo=811de000, task=80456bf0)
> Stack : 804a1800 00000005 8029f62c 80456bf0 00000000 00000000 804a1800 0000000c
> 8043a678 00000001 00000000 803b0000 00000005 8029fcf8 8043a678 8043a5e8
> 00000000 00000001 00000000 803b0000 00000005 8043a5f8 8043a678 8043a5e8
> 00000000 00000001 00000000 803b0000 00000005 802abd0c 00000005 8043a5f8
> b0400074 b040006c 00000001 811dff30 00000000 00000000 00000000 8043a5e8
> ...
> Call Trace:
> [<8029f62c>] hpt_minimum_revision+0x2c/0xec
> [<8029fcf8>] hpt3xx_tune_chipset+0x68/0x2e8
> [<802abd0c>] probe_hwif+0x8a4/0x910
> [<802ace2c>] probe_hwif_init_with_fixup+0x1c/0xcc
> [<802af8bc>] ide_setup_pci_device+0xa8/0xcc
> [<8024f09c>] idr_get_new+0x18/0x4c
> [<80422e38>] ide_scan_pcidev+0x84/0xc4
> [<801c5464>] proc_register+0x48/0x16c
> [<80422eb0>] ide_scan_pcibus+0x38/0xf8
> [<801c5874>] proc_mkdir_mode+0x54/0x80
> [<80422d98>] ide_init+0x68/0x84
> [<80422d7c>] ide_init+0x4c/0x84
> [<801004f8>] init+0x9c/0x264
> [<80105e20>] kernel_thread_helper+0x10/0x18
> [<80105e10>] kernel_thread_helper+0x0/0x18
>
>
> Code: 02002821 080a7e5f a3a20013 <90a20000> 10400008 308400ff
> 00401821 10640007 00000000
> Kernel panic - not syncing: Attempted to kill init!
>
next prev parent reply other threads:[~2005-07-06 7:12 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-07-01 21:17 booting error on db1550 using linux 2.6.12 from linux-mips.org rolf liu
2005-07-01 21:24 ` Pete Popov
2005-07-01 22:35 ` rolf liu
2005-07-01 22:44 ` Pete Popov
2005-07-01 22:52 ` rolf liu
2005-07-05 15:50 ` rolf liu
2005-07-06 7:12 ` Pete Popov [this message]
2005-07-06 22:15 ` rolf liu
2005-07-06 22:22 ` Pete Popov
2005-07-07 17:10 ` Alan Cox
2005-07-07 17:19 ` rolf liu
2005-07-07 18:05 ` rolf liu
2005-07-07 18:42 ` rolf liu
2005-07-07 22:47 ` Alan Cox
2005-07-08 0:27 ` rolf liu
2005-07-08 19:27 ` rolf liu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1120633934.5724.29.camel@localhost.localdomain \
--to=ppopov@embeddedalley.com \
--cc=linux-mips@linux-mips.org \
--cc=rolfliu@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox