From: Thomas Koeller <thomas.koeller@baslerweb.com>
To: Manish Lachwani <mlachwani@mvista.com>
Cc: linux-mips@linux-mips.org
Subject: [PATCH] pmc-sierra yosemite serial i/o support
Date: Thu, 23 Sep 2004 15:11:06 +0200 [thread overview]
Message-ID: <200409231511.06274.thomas.koeller@baslerweb.com> (raw)
In-Reply-To: <4151AB96.4090704@mvista.com>
On Wednesday 22 September 2004 18:43, Manish Lachwani wrote:
>
> Hello Thomas
>
> Sure, please send the patches over to me so that I can take a look at it.
>
> thanks
> Manish
Hi Manish,
here's the patch again, as a diff against current cvs head. It addresses the
following issues:
- avoids autodetection of the uart chip type. The chip was always detected as
a fifo-less 16540. Autodetection really isn't required here, since we know
exactly what we're dealing with.
- enables interrupt sharing for both ports. Since the two uart interrupt lines
are physically ORed together, this makes the second port fully usable.
- use 'arch_initcall' instead of the 'late_time_init' hook, as is appropriate.
thomas
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
diff -ru linux-mips-cvs/arch/mips/pmc-sierra/yosemite/dbg_io.c linux-mips-work/arch/mips/pmc-sierra/yosemite/dbg_io.c
--- linux-mips-cvs/arch/mips/pmc-sierra/yosemite/dbg_io.c 2004-08-20 12:30:47.000000000 +0200
+++ linux-mips-work/arch/mips/pmc-sierra/yosemite/dbg_io.c 2004-09-23 14:04:12.002692920 +0200
@@ -23,18 +23,22 @@
* 675 Mass Ave, Cambridge, MA 02139, USA.
*/
-/*
- * Support for KGDB for the Yosemite board. We make use of single serial
- * port to be used for KGDB as well as console. The second serial port
- * seems to be having a problem. Single IRQ is allocated for both the
- * ports. Hence, the interrupt routing code needs to figure out whether
- * the interrupt came from channel A or B.
- */
-
#include <linux/config.h>
+#include <asm/io.h>
+
+#include "setup.h"
+
#ifdef CONFIG_KGDB
-#include <asm/serial.h>
+
+#if defined(CONFIG_SERIAL_8250) && CONFIG_SERIAL_8250_NR_UARTS > 1
+#error Debug port used by serial driver
+#endif
+
+#define TITAN_UART_CLK 3686400
+#define TITAN_SERIAL_BASE_BAUD (TITAN_UART_CLK / 16)
+#define TITAN_SERIAL_BASE_0 0xfd000008UL
+#define TITAN_SERIAL_BASE_1 0xfd000000UL
/*
* Baud rate, Parity, Data and Stop bit settings for the
@@ -71,6 +75,7 @@
#define SERIAL_SEND_BUFFER 0x0
#define SERIAL_INTR_ENABLE (1 * SERIAL_REG_OFS)
#define SERIAL_INTR_ID (2 * SERIAL_REG_OFS)
+#define SERIAL_FIFO_CONTROL SERIAL_INTR_ID
#define SERIAL_DATA_FORMAT (3 * SERIAL_REG_OFS)
#define SERIAL_LINE_CONTROL (3 * SERIAL_REG_OFS)
#define SERIAL_MODEM_CONTROL (4 * SERIAL_REG_OFS)
@@ -84,59 +89,28 @@
#define SERIAL_DIVISOR_MSB (1 * SERIAL_REG_OFS)
/*
- * Functions to READ and WRITE to serial port 0
+ * Functions to READ and WRITE to serial port
*/
#define SERIAL_READ(ofs) (*((volatile unsigned char*) \
- (TITAN_SERIAL_BASE + ofs)))
-
+ (serbase + ofs)))
#define SERIAL_WRITE(ofs, val) ((*((volatile unsigned char*) \
- (TITAN_SERIAL_BASE + ofs))) = val)
-
-/*
- * Functions to READ and WRITE to serial port 1
- */
-#define SERIAL_READ_1(ofs) (*((volatile unsigned char*) \
- (TITAN_SERIAL_BASE_1 + ofs)
-
-#define SERIAL_WRITE_1(ofs, val) ((*((volatile unsigned char*) \
- (TITAN_SERIAL_BASE_1 + ofs))) = val)
-
-/*
- * Second serial port initialization
- */
-void init_second_port(void)
-{
- /* Disable Interrupts */
- SERIAL_WRITE_1(SERIAL_LINE_CONTROL, 0x0);
- SERIAL_WRITE_1(SERIAL_INTR_ENABLE, 0x0);
+ (serbase + ofs))) = val)
- {
- unsigned int divisor;
-
- SERIAL_WRITE_1(SERIAL_LINE_CONTROL, 0x80);
- divisor = TITAN_SERIAL_BASE_BAUD / YOSEMITE_BAUD_115200;
- SERIAL_WRITE_1(SERIAL_DIVISOR_LSB, divisor & 0xff);
-
- SERIAL_WRITE_1(SERIAL_DIVISOR_MSB,
- (divisor & 0xff00) >> 8);
- SERIAL_WRITE_1(SERIAL_LINE_CONTROL, 0x0);
- }
-
- SERIAL_WRITE_1(SERIAL_DATA_FORMAT, YOSEMITE_DATA_8BIT |
- YOSEMITE_PARITY_NONE | YOSEMITE_STOP_1BIT);
-
- /* Enable Interrupts */
- SERIAL_WRITE_1(SERIAL_INTR_ENABLE, 0xf);
-}
+static int initialized = 0;
/* Initialize the serial port for KGDB debugging */
void debugInit(unsigned int baud, unsigned char data, unsigned char parity,
- unsigned char stop)
+ unsigned char stop)
{
+ initialized = 1;
+
/* Disable Interrupts */
SERIAL_WRITE(SERIAL_LINE_CONTROL, 0x0);
SERIAL_WRITE(SERIAL_INTR_ENABLE, 0x0);
+ /* Disable FIFOs */
+ SERIAL_WRITE(SERIAL_FIFO_CONTROL, 0x00);
+
{
unsigned int divisor;
@@ -152,15 +126,11 @@
SERIAL_WRITE(SERIAL_DATA_FORMAT, data | parity | stop);
}
-static int remoteDebugInitialized = 0;
-
unsigned char getDebugChar(void)
{
- if (!remoteDebugInitialized) {
- remoteDebugInitialized = 1;
+ if (!initialized) {
debugInit(YOSEMITE_BAUD_115200,
- YOSEMITE_DATA_8BIT,
- YOSEMITE_PARITY_NONE, YOSEMITE_STOP_1BIT);
+ YOSEMITE_DATA_8BIT, YOSEMITE_PARITY_NONE, YOSEMITE_STOP_1BIT);
}
while ((SERIAL_READ(SERIAL_LINE_STATUS) & 0x1) == 0);
@@ -169,11 +139,9 @@
int putDebugChar(unsigned char byte)
{
- if (!remoteDebugInitialized) {
- remoteDebugInitialized = 1;
+ if (!initialized) {
debugInit(YOSEMITE_BAUD_115200,
- YOSEMITE_DATA_8BIT,
- YOSEMITE_PARITY_NONE, YOSEMITE_STOP_1BIT);
+ YOSEMITE_DATA_8BIT, YOSEMITE_PARITY_NONE, YOSEMITE_STOP_1BIT);
}
while ((SERIAL_READ(SERIAL_LINE_STATUS) & 0x20) == 0);
diff -ru linux-mips-cvs/arch/mips/pmc-sierra/yosemite/irq.c linux-mips-work/arch/mips/pmc-sierra/yosemite/irq.c
--- linux-mips-cvs/arch/mips/pmc-sierra/yosemite/irq.c 2004-08-20 12:30:47.000000000 +0200
+++ linux-mips-work/arch/mips/pmc-sierra/yosemite/irq.c 2004-09-21 13:22:13.000000000 +0200
@@ -109,10 +109,6 @@
do_IRQ(irq, regs);
}
-#ifdef CONFIG_KGDB
-extern void init_second_port(void);
-#endif
-
/*
* Initialize the next level interrupt handler
*/
@@ -123,15 +119,6 @@
set_except_vector(0, titan_handle_int);
mips_cpu_irq_init(0);
rm7k_cpu_irq_init(8);
-
-#ifdef CONFIG_KGDB
- /* At this point, initialize the second serial port */
- init_second_port();
-#endif
-
-#ifdef CONFIG_GDB_CONSOLE
- register_gdb_console();
-#endif
}
#ifdef CONFIG_KGDB
diff -ru linux-mips-cvs/arch/mips/pmc-sierra/yosemite/setup.c linux-mips-work/arch/mips/pmc-sierra/yosemite/setup.c
--- linux-mips-cvs/arch/mips/pmc-sierra/yosemite/setup.c 2004-09-21 13:08:14.000000000 +0200
+++ linux-mips-work/arch/mips/pmc-sierra/yosemite/setup.c 2004-09-23 11:37:18.106608792 +0200
@@ -24,6 +24,7 @@
* with this program; if not, write to the Free Software Foundation, Inc.,
* 675 Mass Ave, Cambridge, MA 02139, USA.
*/
+#include <linux/config.h>
#include <linux/bcd.h>
#include <linux/init.h>
#include <linux/kernel.h>
@@ -45,6 +46,7 @@
#include <asm/ptrace.h>
#include <asm/reboot.h>
#include <asm/serial.h>
+#include <asm/gdb-stub.h>
#include <linux/termios.h>
#include <linux/tty.h>
#include <linux/serial.h>
@@ -143,12 +145,10 @@
unsigned long uart_base = 0xfd000000L;
-/* No other usable initialization hook than this ... */
-extern void (*late_time_init)(void);
-
unsigned long ocd_base;
-
EXPORT_SYMBOL(ocd_base);
+unsigned long serbase;
+EXPORT_SYMBOL(serbase);
/*
* Common setup before any secondaries are started
@@ -157,11 +157,13 @@
#define TITAN_UART_CLK 3686400
#define TITAN_SERIAL_BASE_BAUD (TITAN_UART_CLK / 16)
#define TITAN_SERIAL_IRQ 4
-#define TITAN_SERIAL_BASE 0xfd000008UL
+#define TITAN_SERIAL_BASE 0xfd000000UL
+#define TITAN_SERIAL_REG_SIZE 8
-static void __init py_map_ocd(void)
+static int __init py_map_ocd(void)
{
- struct uart_port up;
+ static const char serr[] = KERN_ERR "Serial port #%u setup failed\n";
+ struct uart_port up;
/*
* Not specifically interrupt stuff but in case of SMP core_send_ipi
@@ -171,21 +173,46 @@
if (!ocd_base)
panic("Mapping OCD failed - game over. Your score is 0.");
+ /* Map uart registers */
+ serbase = (unsigned long) ioremap(TITAN_SERIAL_BASE, TITAN_SERIAL_REG_SIZE * 2);
+ if (!serbase)
+ panic("Failed to map UART registers");
+
+#if defined(CONFIG_SERIAL_8250)
/*
- * Register to interrupt zero because we share the interrupt with
- * the serial driver which we don't properly support yet.
+ * Set up serial port #0. Do not use autodetection; the result is
+ * not what we want.
*/
memset(&up, 0, sizeof(up));
- up.membase = (unsigned char *) ioremap(TITAN_SERIAL_BASE, 8);
+ up.membase = (char *) (serbase + TITAN_SERIAL_REG_SIZE);
up.irq = TITAN_SERIAL_IRQ;
up.uartclk = TITAN_UART_CLK;
up.regshift = 0;
up.iotype = UPIO_MEM;
- up.flags = ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST;
+ up.type = PORT_16550A;
+ up.flags = UPF_SHARE_IRQ;
up.line = 0;
+ if (early_serial_setup(&up))
+ printk(serr, up.line);
+#if CONFIG_SERIAL_8250_NR_UARTS > 1
+ /* And now for port #1. */
+ up.membase = (char *) serbase;
+ up.line = 1;
if (early_serial_setup(&up))
- printk(KERN_ERR "Early serial init of port 0 failed\n");
+ printk(serr, up.line);
+#endif /* CONFIG_SERIAL_8250_NR_UARTS > 1 */
+#endif /* defined(CONFIG_SERIAL_8250) */
+
+#ifdef CONFIG_KGDB
+ printk(KERN_INFO "Start kgdb ... \n");
+#ifdef CONFIG_GDB_CONSOLE
+ register_gdb_console();
+#endif
+ set_debug_traps();
+ breakpoint();
+#endif
+ return 0;
}
static int __init pmc_yosemite_setup(void)
@@ -193,21 +220,12 @@
extern void pmon_smp_bootstrap(void);
board_time_init = yosemite_time_init;
- late_time_init = py_map_ocd;
/* Add memory regions */
add_memory_region(0x00000000, 0x10000000, BOOT_MEM_RAM);
-#if 0 /* XXX Crash ... */
- OCD_WRITE(RM9000x2_OCD_HTSC,
- OCD_READ(RM9000x2_OCD_HTSC) | HYPERTRANSPORT_ENABLE);
-
- /* Set the BAR. Shifted mode */
- OCD_WRITE(RM9000x2_OCD_HTBAR0, HYPERTRANSPORT_BAR0_ADDR);
- OCD_WRITE(RM9000x2_OCD_HTMASK0, HYPERTRANSPORT_SIZE0);
-#endif
-
return 0;
}
early_initcall(pmc_yosemite_setup);
+arch_initcall(py_map_ocd);
diff -ru linux-mips-cvs/arch/mips/pmc-sierra/yosemite/setup.h linux-mips-work/arch/mips/pmc-sierra/yosemite/setup.h
--- linux-mips-cvs/arch/mips/pmc-sierra/yosemite/setup.h 2004-05-24 12:32:42.000000000 +0200
+++ linux-mips-work/arch/mips/pmc-sierra/yosemite/setup.h 2004-09-21 13:22:13.000000000 +0200
@@ -28,4 +28,7 @@
#define TITAN_ATMEL_24C32_SIZE 32768
#define TITAN_ATMEL_24C64_SIZE 65536
+/* UART base */
+extern unsigned long serbase;
+
#endif /* __SETUP_H__ */
--
--------------------------------------------------
Thomas Koeller, Software Development
Basler Vision Technologies
thomas dot koeller at baslerweb dot com
http://www.baslerweb.com
==============================
prev parent reply other threads:[~2004-09-23 13:08 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2004-09-22 14:51 pmc-sierra yosemite platform Thomas Koeller
2004-09-22 16:43 ` Manish Lachwani
2004-09-23 13:11 ` Thomas Koeller [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200409231511.06274.thomas.koeller@baslerweb.com \
--to=thomas.koeller@baslerweb.com \
--cc=linux-mips@linux-mips.org \
--cc=mlachwani@mvista.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox