From: Thiemo Seufer <ths@networkno.de>
To: linux-mips@linux-mips.org
Subject: Current SGI Octane status
Date: Sat, 9 Jul 2005 11:34:04 +0200 [thread overview]
Message-ID: <20050709093403.GB1586@hattusa.textio> (raw)
Hello All,
I tried current CVS HEAD plus the patches from
ftp://ftp.linux-mips.org/pub/linux/mips/people/skylark/
on an SMP Octane with 2x195 MHz R10000 and ESI graphics.
Results:
- Local console works.
- IOC3 networking works, with 2MB/s maximum for a 30MB http transfer
- Serial console works, but start of output is delayed. The driver
probably lacks transfer bootstrap, and starts transmisssion only when
the first buffer is full.
- Rebooting for SMP works, but this patch apparently broke arcload (hangs
after "Entering Kernel").
- Serial console and framebuffer initializations seem to be mutually
exclusive, that's impractical if you plan to route console (debug)
output over serial while working on the graphics console.
- 'echo "foo" >/dev/fb0' kills the machine.
The dmesg for a serial boot is appended.
Thiemo
[4294667.296000] Linux version 2.6.12-ip30 (ths@hattusa) (gcc version 4.0.1 20050701 (prerelease) (Debian 4.0.0-12)) #21 SMP Sat Jul 9 10:41:57 CEST 2005
[4294667.296000] ARCH: SGI-IP30
[4294667.296000] PROMLIB: ARC firmware Version 64 Revision 0
[4294667.296000] CPU revision is: 00000927
[4294667.296000] FPU revision is: 00000900
[4294667.296000] Silicon Graphics Octane (IP30) support: (c) 2004, 2005 Stanislaw Skowronek.
[4294667.296000] xtalk: Detected XBow (revision 1.2) at 0.
[4294667.296000] xtalk: Detected Heart (revision E) at 8.
[4294667.296000] xtalk: Detected HQ4 / ImpactSR (revision B) at 12.
[4294667.296000] xtalk: Detected Bridge (revision C) at 15.
[4294667.296000] BRIDGE chip at xtalk:15, initializing...
[4294667.296000] Determined physical RAM map:
[4294667.296000] memory: 0000000000004000 @ 0000000000000000 (reserved)
[4294667.296000] memory: 00000000004c6000 @ 0000000020004000 (reserved)
[4294667.296000] memory: 0000000000a36000 @ 00000000204ca000 (usable)
[4294667.296000] memory: 0000000000100000 @ 0000000020f00000 (ROM data)
[4294667.296000] memory: 000000003f000000 @ 0000000021000000 (usable)
[4294667.296000] On node 0 totalpages: 393216
[4294667.296000] DMA zone: 393216 pages, LIFO batch:31
[4294667.296000] Normal zone: 0 pages, LIFO batch:1
[4294667.296000] HighMem zone: 0 pages, LIFO batch:1
[4294667.296000] Built 1 zonelists
[4294667.296000] Kernel command line: root=xio(0)pci(15)scsi(0)disk(1)rdisk(0)partition(0) root=/dev/sda1 console=ttyS0
[4294667.296000] Primary instruction cache 32kB, physically tagged, 2-way, linesize 64 bytes.
[4294667.296000] Primary data cache 32kB, 2-way, linesize 32 bytes.
[4294667.296000] Unified secondary cache 1024kB 2-way, linesize 128 bytes.
[4294667.296000] Synthesized TLB refill handler (41 instructions).
[4294667.296000] Synthesized TLB load handler fastpath (55 instructions).
[4294667.296000] Synthesized TLB store handler fastpath (55 instructions).
[4294667.296000] Synthesized TLB modify handler fastpath (54 instructions).
[4294667.296000] IP30: interrupt controller initialized.
[4294667.296000] PID hash table entries: 4096 (order: 12, 131072 bytes)
[4294667.296000] IP30: initializing timer.
[4294667.296000] 194 MHz CPU detected
[4294667.296000] Using 97.492 MHz high precision timer.
[4294667.296000] Console: colour dummy device 80x25
[4294667.306000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[4294667.325000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[4294667.560000] Memory: 1017476k/1042648k available (3180k kernel code, 24828k reserved, 1222k data, 248k init, 0k highmem)
[4294667.561000] Calibrating delay loop... 193.53 BogoMIPS (lpj=96768)
[4294667.578000] Mount-cache hash table entries: 256
[4294667.579000] Checking for 'wait' instruction... unavailable.
[4294667.579000] Checking for the multiply/shift bug... no.
[4294667.579000] Checking for the daddi bug... no.
[4294667.579000] Checking for the daddiu bug... no.
[4294667.580000] CPU revision is: 00000927
[4294667.580000] FPU revision is: 00000900
[4294667.580000] Primary instruction cache 32kB, physically tagged, 2-way, linesize 64 bytes.
[4294667.580000] Primary data cache 32kB, 2-way, linesize 32 bytes.
[4294667.580000] Unified secondary cache 1024kB 2-way, linesize 128 bytes.
[4294667.582000] Synthesized TLB refill handler (41 instructions).
[4294667.582000] Calibrating delay loop... 194.56 BogoMIPS (lpj=97280)
[4294667.599000] Brought up 2 CPUs
[4294667.599000] CPU0 attaching sched-domain:
[4294667.599000] domain 0: span 3
[4294667.599000] groups: 1 2
[4294667.599000] CPU1 attaching sched-domain:
[4294667.599000] domain 0: span 3
[4294667.599000] groups: 2 1
[4294667.603000] NET: Registered protocol family 16
[4294667.609000] SCSI subsystem initialized
[4294667.610000] IP30: HEART ATTACK! Caught errors: 0x1040!
[4294667.610000] interrupt #63
[4294667.610000] interrupt #57
[4294667.622000] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[4294667.623000] Initializing Cryptographic API
[4294667.623000] PCI: Fixing ioc3 in [bus:slot.fn] 0000:00:02.0
[4294667.623000] PCI: Fixing rad1 in [bus:slot.fn] 0000:00:03.0
[4294667.711000] Console: switching to colour frame buffer device 160x64
[4294667.711000] fb0: ImpactSR 1RSS frame buffer device
[4294667.848000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
[4294667.850000] io scheduler noop registered
[4294667.850000] io scheduler anticipatory registered
[4294667.850000] io scheduler deadline registered
[4294667.850000] io scheduler cfq registered
[4294667.854000] RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
[4294667.856000] loop: loaded (max 8 devices)
[4294667.856000] tun: Universal TUN/TAP device driver, 1.6
[4294667.856000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[4294667.857000] qla1280: QLA1040 found on PCI bus 0, dev 0
[4294667.857000] PCI: Enabling device 0000:00:00.0 (0006 -> 0007)
[4294668.577000] scsi(0:0): Resetting SCSI BUS
[4294668.579000] scsi0 : QLogic QLA1040 PCI to SCSI Host Adapter
[4294668.579000] Firmware version: 7.65.00, Driver version 3.25
[4294670.747000] Vendor: SEAGATE Model: ST318275LC Rev: 0001
[4294670.747000] Type: Direct-Access ANSI SCSI revision: 02
[4294670.748000] scsi(0:0:1:0): Sync: period 10, offset 12, Wide
[4294672.921000] qla1280: QLA1040 found on PCI bus 0, dev 1
[4294672.921000] PCI: Enabling device 0000:00:01.0 (0006 -> 0007)
[4294673.653000] scsi(1:0): Resetting SCSI BUS
[4294673.656000] scsi1 : QLogic QLA1040 PCI to SCSI Host Adapter
[4294673.656000] Firmware version: 7.65.00, Driver version 3.25
[4294678.158000] SCSI device sda: 35566480 512-byte hdwr sectors (18210 MB)
[4294678.160000] SCSI device sda: drive cache: write back
[4294678.162000] SCSI device sda: 35566480 512-byte hdwr sectors (18210 MB)
[4294678.164000] SCSI device sda: drive cache: write back
[4294678.164000] sda: sda1 sda2 sda9 sda11
[4294678.182000] Attached scsi disk sda at scsi0, channel 0, id 1, lun 0
[4294678.183000] mice: PS/2 mouse device common for all mice
[4294678.183000] md: raid0 personality registered as nr 2
[4294678.183000] md: raid1 personality registered as nr 3
[4294678.183000] md: raid5 personality registered as nr 4
[4294678.183000] raid5: measuring checksumming speed
[4294678.188000] 8regs : 500.000 MB/sec
[4294678.193000] 8regs_prefetch: 476.000 MB/sec
[4294678.198000] 32regs : 496.000 MB/sec
[4294678.203000] 32regs_prefetch: 476.000 MB/sec
[4294678.203000] raid5: using function: 8regs (500.000 MB/sec)
[4294678.203000] md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
[4294678.203000] Advanced Linux Sound Architecture Driver Version 1.0.9rc2 (Thu Mar 24 10:33:39 2005 UTC).
[4294678.208000] ALSA device list:
[4294678.208000] #0: SGI RAD Pro Audio at 0x1fa00000
[4294679.420000] IOC3 part: [030-0891-003], serial: [DJK972] => class IP30 system
[4294679.421000] ttyS0 at IOC3 0x1f620178 (irq = 64) is a 16550A
[4294679.423000] ttyS1 at IOC3 0x1f620170 (irq = 64) is a 16550A
[4294679.428000] Ethernet address is 08:00:69:0a:fc:0f.
[4294679.441000] eth0: link up, 100Mbps, half-duplex, lpa 0x00A1
[4294679.442000] eth0: Using PHY 1, vendor 0x15f42, model 2, rev 3.
[4294679.443000] eth0: IOC3 SSRAM has 128 kbyte.
[4294679.444000] IOC3 Master Driver loaded for 0000:00:02.0
[4294679.445000] NET: Registered protocol family 2
[4294679.548000] atkbd.c: keyboard reset failed on ioc3/serio0kbd
[4294680.035000] atkbd.c: keyboard reset failed on ioc3/serio0aux
[4294680.429000] IP: routing cache hash table of 8192 buckets, 128Kbytes
[4294680.431000] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[4294680.463000] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[4294680.471000] TCP: Hash tables configured (established 262144 bind 65536)
[4294680.472000] NET: Registered protocol family 1
[4294680.473000] NET: Registered protocol family 17
[4294680.474000] NET: Registered protocol family 15
[4294680.476000] md: Autodetecting RAID arrays.
[4294680.477000] md: autorun ...
[4294680.478000] md: ... autorun DONE.
[4294680.506000] kjournald starting. Commit interval 5 seconds
[4294680.581000] EXT3-fs: mounted filesystem with ordered data mode.
[4294680.662000] VFS: Mounted root (ext3 filesystem) readonly.
[4294680.736000] Freeing prom memory: 1024kb freed
[4294680.796000] Freeing unused kernel memory: 1272k freed
[4294683.050000] Adding 907664k swap on /dev/sda2. Priority:-1 extents:1
[4294683.389000] EXT3 FS on sda1, internal journal
next reply other threads:[~2005-07-09 9:33 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-07-09 9:34 Thiemo Seufer [this message]
2005-07-09 16:37 ` Current SGI Octane status Stanislaw Skowronek
2005-07-09 21:20 ` Thiemo Seufer
2005-07-11 22:27 ` Ralf Baechle
2005-07-12 7:21 ` Stanislaw Skowronek
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20050709093403.GB1586@hattusa.textio \
--to=ths@networkno.de \
--cc=linux-mips@linux-mips.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox