Linux version 2.6.23-rc3-gb377fd39 (tbm@em64t) (gcc version 4.1.2 20061028 (prerelease) (Debian 4.1.1-19)) #46 Thu Aug 23 09:06:46 UTC 2007
console [early0] enabled
CPU revision is: 00002810
FPU revision is: 00002810
Determined physical RAM map:
 memory: 03000000 @ 00000000 (usable)
Built 1 zonelists in Zone order.  Total pages: 12192
Kernel command line: console=ttyS0,115200 root=/dev/sda1
Primary instruction cache 16kB, physically tagged, 2-way, linesize 32 bytes.
Primary data cache 16kB, 2-way, linesize 32 bytes.
Synthesized TLB refill handler (21 instructions).
Synthesized TLB load handler fastpath (34 instructions).
Synthesized TLB store handler fastpath (34 instructions).
Synthesized TLB modify handler fastpath (33 instructions).
PID hash table entries: 256 (order: 8, 1024 bytes)
Console: colour dummy device 80x25
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 45080k/49152k available (2445k kernel code, 4056k reserved, 447k data, 96k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
SCSI subsystem initialized
Galileo: revision 2
Galileo: PCI retry count exceeded (06.0)
Cobalt board ID: 4
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Activating ISA DMA hang workarounds.
Cobalt LCD Driver v2.10
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
˙serial8250.0: ttyS0 at MMIO 0x1c800000 (irq = 21) is a ST16650V2
console handover: boot [early0] -> real [ttyS0]
loop: module loaded
Linux Tulip driver version 1.1.15 (Feb 27, 2007)
PCI: Enabling device 0000:00:07.0 (0041 -> 0043)
tulip0: Old format EEPROM on 'Cobalt Microserver' board.  Using substitute media control info.
tulip0:  EEPROM default media type Autosense.
tulip0:  Index #0 - Media MII (#11) described by a 21142 MII PHY (3) block.
tulip0:  MII transceiver #1 config 1000 status 7809 advertising 01e1.
eth0: Digital DS21142/43 Tulip rev 65 at Port 0x1000, 00:10:E0:00:27:5C, IRQ 20.
PCI: Unable to reserve I/O region #1:8@f00001f0 for device 0000:00:09.1
pata_via 0000:00:09.1: failed to request/iomap BARs for port 0 (errno=-16)
PCI: Unable to reserve I/O region #3:8@f0000170 for device 0000:00:09.1
pata_via 0000:00:09.1: failed to request/iomap BARs for port 1 (errno=-16)
pata_via 0000:00:09.1: no available native port
physmap platform flash device: 00080000 at 1fc00000
Found: AMD AM29F040
physmap-flash.0: Found 1 x8 devices at 0x0 in 8-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
Using physmap partition information
Creating 1 MTD partitions on "physmap-flash.0":
0x00000000-0x00080000 : "firmware"
input: Cobalt buttons as /class/input/input0
rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one day
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15