[PATCH AUTOSEL 4.14 04/39] MIPS: lantiq: dma: add small delay after reset

[PATCH AUTOSEL 4.14 04/39] MIPS: lantiq: dma: add small delay after reset

[Sasha Levin]

From: Aleksander Jan Bajkowski <olek2@wp.pl>

[ Upstream commit c12aa581f6d5e80c3c3675ab26a52c2b3b62f76e ]

Reading the DMA registers immediately after the reset causes
Data Bus Error. Adding a small delay fixes this issue.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/mips/lantiq/xway/dma.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/mips/lantiq/xway/dma.c b/arch/mips/lantiq/xway/dma.c
index 805b3a6ab2d60..ce7e033b4bb18 100644
--- a/arch/mips/lantiq/xway/dma.c
+++ b/arch/mips/lantiq/xway/dma.c
@@ -22,6 +22,7 @@
 #include <linux/export.h>
 #include <linux/spinlock.h>
 #include <linux/clk.h>
+#include <linux/delay.h>
 #include <linux/err.h>
 
 #include <lantiq_soc.h>
@@ -234,6 +235,8 @@ ltq_dma_init(struct platform_device *pdev)
 	clk_enable(clk);
 	ltq_dma_w32_mask(0, DMA_RESET, LTQ_DMA_CTRL);
 
+	usleep_range(1, 10);
+
 	/* disable all interrupts */
 	ltq_dma_w32(0, LTQ_DMA_IRNEN);
 
-- 
2.33.0

[PATCH AUTOSEL 4.14 05/39] MIPS: lantiq: dma: reset correct number of channel

[Sasha Levin]

From: Aleksander Jan Bajkowski <olek2@wp.pl>

[ Upstream commit 5ca9ce2ba4d5884cd94d1a856c675ab1242cd242 ]

Different SoCs have a different number of channels, e.g .:
* amazon-se has 10 channels,
* danube+ar9 have 20 channels,
* vr9 has 28 channels,
* ar10 has 24 channels.

We can read the ID register and, depending on the reported
number of channels, reset the appropriate number of channels.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/mips/lantiq/xway/dma.c | 11 ++++++-----
 1 file changed, 6 insertions(+), 5 deletions(-)

diff --git a/arch/mips/lantiq/xway/dma.c b/arch/mips/lantiq/xway/dma.c
index ce7e033b4bb18..0de61165ef6e4 100644
--- a/arch/mips/lantiq/xway/dma.c
+++ b/arch/mips/lantiq/xway/dma.c
@@ -41,6 +41,7 @@
 #define LTQ_DMA_PCTRL		0x44
 #define LTQ_DMA_IRNEN		0xf4
 
+#define DMA_ID_CHNR		GENMASK(26, 20)	/* channel number */
 #define DMA_DESCPT		BIT(3)		/* descriptor complete irq */
 #define DMA_TX			BIT(8)		/* TX channel direction */
 #define DMA_CHAN_ON		BIT(0)		/* channel on / off bit */
@@ -51,7 +52,6 @@
 #define DMA_POLL		BIT(31)		/* turn on channel polling */
 #define DMA_CLK_DIV4		BIT(6)		/* polling clock divider */
 #define DMA_2W_BURST		BIT(1)		/* 2 word burst length */
-#define DMA_MAX_CHANNEL		20		/* the soc has 20 channels */
 #define DMA_ETOP_ENDIANNESS	(0xf << 8) /* endianness swap etop channels */
 #define DMA_WEIGHT	(BIT(17) | BIT(16))	/* default channel wheight */
 
@@ -219,7 +219,7 @@ ltq_dma_init(struct platform_device *pdev)
 {
 	struct clk *clk;
 	struct resource *res;
-	unsigned id;
+	unsigned int id, nchannels;
 	int i;
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
@@ -241,17 +241,18 @@ ltq_dma_init(struct platform_device *pdev)
 	ltq_dma_w32(0, LTQ_DMA_IRNEN);
 
 	/* reset/configure each channel */
-	for (i = 0; i < DMA_MAX_CHANNEL; i++) {
+	id = ltq_dma_r32(LTQ_DMA_ID);
+	nchannels = ((id & DMA_ID_CHNR) >> 20);
+	for (i = 0; i < nchannels; i++) {
 		ltq_dma_w32(i, LTQ_DMA_CS);
 		ltq_dma_w32(DMA_CHAN_RST, LTQ_DMA_CCTRL);
 		ltq_dma_w32(DMA_POLL | DMA_CLK_DIV4, LTQ_DMA_CPOLL);
 		ltq_dma_w32_mask(DMA_CHAN_ON, 0, LTQ_DMA_CCTRL);
 	}
 
-	id = ltq_dma_r32(LTQ_DMA_ID);
 	dev_info(&pdev->dev,
 		"Init done - hw rev: %X, ports: %d, channels: %d\n",
-		id & 0x1f, (id >> 16) & 0xf, id >> 20);
+		id & 0x1f, (id >> 16) & 0xf, nchannels);
 
 	return 0;
 }
-- 
2.33.0