[PATCH net-next v6 6/6] mips: dts: cameo-rtl9302c: Add switch block

[Chris Packham <chris.packham@alliedtelesis.co.nz>]

Add the switch port and phys to the cameo-rtl9302c-2x-rtl8224-2xge
board.

Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
---

Notes:
    Changes in v6:
    - New. This is needed to comply with the updated bindings. It could
      possibly be split to add the ports then the PHYs. Technically the
      ports are the required property that dtbs_check will complain about
      but it didn't seem worth separating out the PHYs.

 .../cameo-rtl9302c-2x-rtl8224-2xge.dts        | 96 +++++++++++++++++++
 1 file changed, 96 insertions(+)

diff --git a/arch/mips/boot/dts/realtek/cameo-rtl9302c-2x-rtl8224-2xge.dts b/arch/mips/boot/dts/realtek/cameo-rtl9302c-2x-rtl8224-2xge.dts
index 6789bf374044..28ab2442b37a 100644
--- a/arch/mips/boot/dts/realtek/cameo-rtl9302c-2x-rtl8224-2xge.dts
+++ b/arch/mips/boot/dts/realtek/cameo-rtl9302c-2x-rtl8224-2xge.dts
@@ -71,3 +71,99 @@ partition@1180000 {
 		};
 	};
 };
+
+&mdio0 {
+	/* External RTL8224 */
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+		compatible = "ethernet-phy-ieee802.3-c45";
+	};
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+		compatible = "ethernet-phy-ieee802.3-c45";
+	};
+	phy2: ethernet-phy@2 {
+		reg = <2>;
+		compatible = "ethernet-phy-ieee802.3-c45";
+	};
+	phy3: ethernet-phy@3 {
+		reg = <3>;
+		compatible = "ethernet-phy-ieee802.3-c45";
+	};
+};
+
+&mdio1 {
+	/* External RTL8224 */
+	phy4: ethernet-phy@0 {
+		reg = <0>;
+		compatible = "ethernet-phy-ieee802.3-c45";
+	};
+	phy5: ethernet-phy@1 {
+		reg = <1>;
+		compatible = "ethernet-phy-ieee802.3-c45";
+	};
+	phy6: ethernet-phy@2 {
+		reg = <2>;
+		compatible = "ethernet-phy-ieee802.3-c45";
+	};
+	phy7: ethernet-phy@3 {
+		reg = <3>;
+		compatible = "ethernet-phy-ieee802.3-c45";
+	};
+};
+
+&switch0 {
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			phy-handle = <&phy0>;
+			phy-mode = "usxgmii";
+		};
+		port@1 {
+			reg = <1>;
+			phy-handle = <&phy1>;
+			phy-mode = "usxgmii";
+		};
+		port@2 {
+			reg = <2>;
+			phy-handle = <&phy2>;
+			phy-mode = "usxgmii";
+		};
+		port@3 {
+			reg = <3>;
+			phy-handle = <&phy3>;
+			phy-mode = "usxgmii";
+		};
+		port@16 {
+			reg = <16>;
+			phy-handle = <&phy4>;
+			phy-mode = "usxgmii";
+		};
+		port@17 {
+			reg = <17>;
+			phy-handle = <&phy5>;
+			phy-mode = "usxgmii";
+		};
+		port@18 {
+			reg = <18>;
+			phy-handle = <&phy6>;
+			phy-mode = "usxgmii";
+		};
+		port@19 {
+			reg = <19>;
+			phy-handle = <&phy7>;
+			phy-mode = "usxgmii";
+		};
+		port@24{
+			reg = <24>;
+			phy-mode = "10gbase-r";
+		};
+		port@25{
+			reg = <25>;
+			phy-mode = "10gbase-r";
+		};
+	};
+};
-- 
2.48.1