From: Hartvig Ekner <hartvig@ekner.info>
To: Linux MIPS mailing list <linux-mips@linux-mips.org>
Subject: IRQ warnings during boot on Au1500/DB1500
Date: Thu, 13 Mar 2003 21:32:15 +0100 [thread overview]
Message-ID: <3E70EACF.8F6629E4@ekner.info> (raw)
Hi,
with current 2.4 CVS, I get these messages during boot on a DB1500:
...
eth0: Using AMD 79C874 10/100 BaseT PHY as default
eth1: Au1xxx ethernet found at 0xb1510000, irq 29
eth1: AMD 79C874 10/100 BaseT PHY at phy address 31
eth1: Using AMD 79C874 10/100 BaseT PHY as default
Uniform Multi-Platform E-IDE driver Revision: 7.00beta-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PDC20268: IDE controller at PCI slot 00:0d.0
PDC20268: chipset revision 2
PDC20268: not 100% native mode: will probe irqs later
PDC20268: ROM enabled at 0x000dc000
ide0: BM-DMA at 0x0520-0x0527, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x0528-0x052f, BIOS settings: hdc:pio, hdd:pio
hda: IBM-DTLA-307030, ATA DISK drive
blk: queue 802d01e0, I/O limit 4095Mb (mask 0xffffffff)
warning: end_irq 62 did not enable (6)
warning: end_irq 60 did not enable (6)
warning: end_irq 59 did not enable (6)
warning: end_irq 58 did not enable (6)
warning: end_irq 57 did not enable (6)
warning: end_irq 55 did not enable (6)
warning: end_irq 54 did not enable (6)
warning: end_irq 52 did not enable (6)
warning: end_irq 51 did not enable (6)
warning: end_irq 50 did not enable (6)
warning: end_irq 49 did not enable (6)
warning: end_irq 48 did not enable (6)
warning: end_irq 46 did not enable (6)
warning: end_irq 45 did not enable (6)
warning: end_irq 44 did not enable (6)
warning: end_irq 43 did not enable (6)
warning: end_irq 42 did not enable (6)
warning: end_irq 41 did not enable (6)
warning: end_irq 40 did not enable (6)
warning: end_irq 39 did not enable (6)
warning: end_irq 38 did not enable (6)
warning: end_irq 18 did not enable (6)
warning: end_irq 14 did not enable (6)
warning: end_irq 62 did not enable (16)
warning: end_irq 60 did not enable (16)
warning: end_irq 59 did not enable (16)
warning: end_irq 58 did not enable (16)
warning: end_irq 57 did not enable (16)
warning: end_irq 55 did not enable (16)
warning: end_irq 54 did not enable (16)
warning: end_irq 52 did not enable (16)
warning: end_irq 51 did not enable (16)
warning: end_irq 50 did not enable (16)
warning: end_irq 49 did not enable (16)
warning: end_irq 48 did not enable (16)
warning: end_irq 46 did not enable (16)
warning: end_irq 45 did not enable (16)
warning: end_irq 44 did not enable (16)
warning: end_irq 43 did not enable (16)
warning: end_irq 42 did not enable (16)
warning: end_irq 41 did not enable (16)
warning: end_irq 40 did not enable (16)
warning: end_irq 39 did not enable (16)
warning: end_irq 38 did not enable (16)
warning: end_irq 18 did not enable (16)
hde: IRQ probe failed (0xfffbfffe)
warning: end_irq 62 did not enable (6)
warning: end_irq 60 did not enable (6)
warning: end_irq 59 did not enable (6)
warning: end_irq 58 did not enable (6)
warning: end_irq 57 did not enable (6)
warning: end_irq 55 did not enable (6)
warning: end_irq 54 did not enable (6)
warning: end_irq 52 did not enable (6)
warning: end_irq 51 did not enable (6)
warning: end_irq 50 did not enable (6)
warning: end_irq 49 did not enable (6)
Once the IDE probing is done, these messages don't seem to appear any more, and the kernel runs ok. Anybody seeing similar messages?
/Hartvig
next reply other threads:[~2003-03-13 20:28 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2003-03-13 20:32 Hartvig Ekner [this message]
2003-03-13 20:36 ` IRQ warnings during boot on Au1500/DB1500 Pete Popov
2003-03-13 22:16 ` Jeff Baitis
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=3E70EACF.8F6629E4@ekner.info \
--to=hartvig@ekner.info \
--cc=linux-mips@linux-mips.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox