From mboxrd@z Thu Jan 1 00:00:00 1970 Received: with ECARTIS (v1.0.0; list linux-mips); Tue, 24 Feb 2004 11:55:59 +0000 (GMT) Received: from [IPv6:::ffff:62.13.60.4] ([IPv6:::ffff:62.13.60.4]:48398 "EHLO mail.swemic.net") by linux-mips.org with ESMTP id ; Tue, 24 Feb 2004 11:55:56 +0000 Received: from localhost (localhost [127.0.0.1]) by mail.swemic.net (Postfix) with ESMTP id 1BD1D75DBB; Tue, 24 Feb 2004 12:55:52 +0100 (CET) Received: from mail.swemic.net ([127.0.0.1]) by localhost (seagle [127.0.0.1]) (amavisd-new, port 10024) with SMTP id 08257-03; Tue, 24 Feb 2004 12:55:38 +0100 (CET) Received: from corelatus.se (skokloster.swemic.net [62.13.60.22]) by mail.swemic.net (Postfix) with ESMTP id AF33775D83; Tue, 24 Feb 2004 12:55:37 +0100 (CET) Message-ID: <403B3BB8.8090403@corelatus.se> Date: Tue, 24 Feb 2004 12:55:36 +0100 From: Thomas Lange User-Agent: Mozilla/5.0 (X11; U; Linux i686; en-US; rv:1.5) Gecko/20031021 X-Accept-Language: en-us, en MIME-Version: 1.0 To: "Liu Hongming (Alan)" Cc: linux-mips@linux-mips.org Subject: Re: IDE driver problem References: <15F9E1AE3207D6119CEA00D0B7DD5F680219C648@TMTMS> In-Reply-To: <15F9E1AE3207D6119CEA00D0B7DD5F680219C648@TMTMS> X-Enigmail-Version: 0.82.6.0 X-Enigmail-Supports: pgp-inline, pgp-mime Content-Type: text/plain; charset=us-ascii; format=flowed Content-Transfer-Encoding: 7bit X-Virus-Scanned: by amavisd-new at hawk.swemic.net Return-Path: X-Envelope-To: <"|/home/ecartis/ecartis -s linux-mips"> (uid 0) X-Orcpt: rfc822;linux-mips@linux-mips.org Original-Recipient: rfc822;linux-mips@linux-mips.org X-archive-position: 4423 X-ecartis-version: Ecartis v1.0.0 Sender: linux-mips-bounce@linux-mips.org Errors-to: linux-mips-bounce@linux-mips.org X-original-sender: thomas@corelatus.se Precedence: bulk X-list: linux-mips The partition table is written to the first partition on the device, in your example hda1. Use mke2fs on hda2 and I am sure it work just great. Cheers, /Thomas Liu Hongming (Alan) wrote: > Hi All, > > I am porting IDE drivers(Since my hardware has endian issue), > and now it could work,however it has some abnormal problems: > > I could 'fdisk' /dev/hda,and partition it into several partitions. > After this,I reboot my board and see all the partitions is there. > Then I 'mke2fs' on /dev/hda1,after this, when using 'fdisk' again, > I found all partitions gone! At this time,I could not access /dev/hda1 > any more.However, I could 'mount /dev/hda /opt', it really worked,and > I could create/read/write/erase files in it. > > I dumped the first sector of Hard disk and found that it has been > zeroed.Now I dont know what the problem is,since I am not familiar > with fs parts of linux kernel,and I dont know what 'mke2fs' has done. > > Any advice? > > Alan > > -----Original Message----- > From: Kevin D. Kissell [mailto:kevink@mips.com] > Sent: Tuesday, February 24, 2004 6:47 AM > To: Mark and Janice Juszczec; linux-mips@linux-mips.org > Cc: uhler@mips.com; dom@mips.com; echristo@redhat.com > Subject: Re: r3000 instruction set > > > Kaffe's makefiles won't pick up on configuration changes, so any time > you re-configure for a different engine or debug level, you need to do > a make clean. At least, that's the way it was the last time I worked on > it. > If you had a partial build with JIT, then changed to intrp, then you could > get all kinds of strange behavior. The address range of your error us a > dead giveaway. It's too high to be the kaffe code segment, but too low > to be a shared library. It's where I'd expect the heap to be, and where > I remember the JIT buffers being allocated when I was trying to debug > that stuff. > > > Its been a few weeks since I built this version of kaffe. The configure > > output says I did specify --with-engine=intrp. I'll delete the compiled > > stuff, reconfigure (double checking that I give it --with-engine=intrp), > > recompile and retest. > > > > I'll post my results. > > > > Mark > > > > > > > > >From: "Kevin D. Kissell" > > >To: "Mark and Janice Juszczec" , > > > > > >CC: , , > > >Subject: Re: r3000 instruction set > > >Date: Mon, 23 Feb 2004 18:21:19 +0100 > > > > > > > Someone suggested posting the message I get. Here it is: > > > > > > > > >./kaffe-bin FirstClass > > > > [kaffe-bin:6] Illgal instruction 674696a at 2abb034, ra=2adbffd0, > > > > P0_STATUS=0000500 > > > > pid 6: killed (signal 4) > > > > >Reading command line: Try again > > > > Kernel panic: Attmpted to kill int! > > > > > >Let me guess. You are running little-endian. The instruction word > > >in memory would be 0x6a697406. Do you think it's a coincidence > > >that 0x6a6974 spells "jit" in ASCII? ;o) > > > > > >The reported address range looks like that where kaffe builds its > > >JITted instruciton buffers in MIPS/Linux. And, like I say, JIT is > > >somewhat broken for MIPS in Kaffe. Which version of the kaffe sources > > >are you building, and have you tried configuring with > --with-engine=intrp > > >as I suggested? > > > > > > Regards, > > > > > > Kevin K. > > > > _________________________________________________________________ > > Click, drag and drop. My MSN is the simple way to design your homepage. > > http://click.atdmt.com/AVE/go/onm00200364ave/direct/01/ > > > > >