[PATCH 0/3] staging: octeon: Convert to use phylink

[Ladislav Michl <oss-lists@triops.cz>]

The purpose of this patches is to provide support for SFP cage to
Octeon ethernet driver. This is tested with following DT snippet:

	smi0: mdio@1180000001800 {
		compatible = "cavium,octeon-3860-mdio";
		#address-cells = <1>;
		#size-cells = <0>;
		reg = <0x11800 0x00001800 0x0 0x40>;

		/* QSGMII PHY */
		phy0: ethernet-phy@0 {
			compatible = "marvell,88e154", "ethernet-phy-ieee802.3-c22";
			reg = <0>;
			interrupt-parent = <&gpio>;
			interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
			marvell,reg-init =
			  <0xff 24 0 0x2800>, <0xff 23 0 0x2001>, /* errata 3.1.1 - PHY Initialization #1 */
			  <0 29 0 3>, <0 30 0 2>, <0 29 0 0>,	  /* errata 3.1.2 - PHY Initialization #2 */
			  <4 26 0 0x2>, 			  /* prekrizeni RX a TX QSGMII sbernice */
			  <4 0 0x1000 0x1000>, 			  /* Q_ANEG workaround: P4R0B12 = 1 */
			  <3 16 0 0x1117>;			  /* nastavení LED: G=link+act, Y=1Gbit */
		};
		phy1: ethernet-phy@1 {
			compatible = "marvell,88e154", "ethernet-phy-ieee802.3-c22";
			reg = <1>;
			interrupt-parent = <&gpio>;
			interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
			marvell,reg-init =
			  <4 0 0x1000 0x1000>,			  /* Q_ANEG workaround: P4R0B12 = 1 */
			  <3 16 0 0x1117>;			  /* nastavení LED: G=link+act, Y=1Gbit */
		};
		phy2: ethernet-phy@2 {
			compatible = "marvell,88e154", "ethernet-phy-ieee802.3-c22";
			reg = <2>;
			interrupt-parent = <&gpio>;
			interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
			marvell,reg-init =
			  <4 0 0x1000 0x1000>,			  /* Q_ANEG workaround: P4R0B12 = 1 */
			  <3 16 0 0x1117>;			  /* nastavení LED: G=link+act, Y=1Gbit */
		};
		phy3: ethernet-phy@3 {
			compatible = "marvell,88e154", "ethernet-phy-ieee802.3-c22";
			reg = <3>;
			interrupt-parent = <&gpio>;
			interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
			marvell,reg-init =
			  <4 0 0x1000 0x1000>,			  /* Q_ANEG workaround: P4R0B12 = 1 */
			  <3 16 0 0x1117>;			  /* nastavení LED: G=link+act, Y=1Gbit */
		};
	};

	pip: pip@11800a0000000 {
		compatible = "cavium,octeon-3860-pip";
		#address-cells = <1>;
		#size-cells = <0>;
		reg = <0x11800 0xa0000000 0x0 0x2000>;

		/* Interface 0 goes to SFP */
		interface@0 {
			compatible = "cavium,octeon-3860-pip-interface";
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0>; /* interface */

			ethernet@0 {
				compatible = "cavium,octeon-3860-pip-port";
				reg = <0>; /* Port */
				local-mac-address = [ 00 00 00 00 00 00 ];
				managed = "in-band-status";
				phy-connection-type = "1000base-x";
				sfp = <&sfp>;
			};
		};
		/* Interface 1 goes to eth1-eth4 and is QSGMII */
		interface@1 {
			compatible = "cavium,octeon-3860-pip-interface";
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <1>; /* interface */

			ethernet@0 {
				compatible = "cavium,octeon-3860-pip-port";
				reg = <0>; /* Port */
				local-mac-address = [ 00 00 00 00 00 00 ];
				phy-handle = <&phy0>;
			};
			ethernet@1 {
				compatible = "cavium,octeon-3860-pip-port";
				reg = <1>; /* Port */
				local-mac-address = [ 00 00 00 00 00 00 ];
				phy-handle = <&phy1>;
			};
			ethernet@2 {
				compatible = "cavium,octeon-3860-pip-port";
				reg = <2>; /* Port */
				local-mac-address = [ 00 00 00 00 00 00 ];
				phy-handle = <&phy2>;
			};
			ethernet@3 {
				compatible = "cavium,octeon-3860-pip-port";
				reg = <3>; /* Port */
				local-mac-address = [ 00 00 00 00 00 00 ];
				phy-handle = <&phy3>;
			};
		};
	};

However testing revealed some glitches:
1. driver previously returned -EPROBE_DEFER when no phy was attached.
Phylink stack does not seem to do so, which end up with:

Marvell PHY driver as a module:
octeon_ethernet 11800a0000000.pip eth0: configuring for inband/1000base-x link mode
octeon_ethernet 11800a0000000.pip eth1: PHY [8001180000001800:00] driver [Generic PHY] (irq=POLL)
octeon_ethernet 11800a0000000.pip eth1: configuring for phy/sgmii link mode
octeon_ethernet 11800a0000000.pip eth2: PHY [8001180000001800:01] driver [Generic PHY] (irq=POLL)
octeon_ethernet 11800a0000000.pip eth2: configuring for phy/sgmii link mode
octeon_ethernet 11800a0000000.pip eth0: switched to inband/sgmii link mode
octeon_ethernet 11800a0000000.pip eth0: PHY [i2c:sfp:16] driver [Marvell 88E1111] (irq=POLL)
octeon_ethernet 11800a0000000.pip eth3: PHY [8001180000001800:02] driver [Marvell 88E1340S] (irq=25)
octeon_ethernet 11800a0000000.pip eth3: configuring for phy/sgmii link mode
octeon_ethernet 11800a0000000.pip eth4: PHY [8001180000001800:03] driver [Marvell 88E1340S] (irq=25)
octeon_ethernet 11800a0000000.pip eth4: configuring for phy/sgmii link mode
octeon_ethernet 11800a0000000.pip eth1: Link is Up - 100Mbps/Full - flow control off

Marvell PHY driver built-in:
octeon_ethernet 11800a0000000.pip eth0: configuring for inband/1000base-x link mode
octeon_ethernet 11800a0000000.pip eth1: PHY [8001180000001800:00] driver [Marvell 88E1340S] (irq=25)
octeon_ethernet 11800a0000000.pip eth1: configuring for phy/sgmii link mode
Error: Driver 'Marvell 88E1101' is already registered, aborting...
libphy: Marvell 88E1101: Error -16 in registering driver
Error: Driver 'Marvell 88E1101' is already registered, aborting...
libphy: Marvell 88E1101: Error -16 in registering driver
octeon_ethernet 11800a0000000.pip eth0: switched to inband/sgmii link mode
octeon_ethernet 11800a0000000.pip eth0: PHY [i2c:sfp:16] driver [Marvell 88E1111] (irq=POLL)
octeon_ethernet 11800a0000000.pip eth2: PHY [8001180000001800:01] driver [Marvell 88E1340S] (irq=25)
octeon_ethernet 11800a0000000.pip eth2: configuring for phy/sgmii link mode
octeon_ethernet 11800a0000000.pip eth3: PHY [8001180000001800:02] driver [Marvell 88E1340S] (irq=25)
octeon_ethernet 11800a0000000.pip eth3: configuring for phy/sgmii link mode
octeon_ethernet 11800a0000000.pip eth4: PHY [8001180000001800:03] driver [Marvell 88E1340S] (irq=25)
octeon_ethernet 11800a0000000.pip eth4: configuring for phy/sgmii link mode
octeon_ethernet 11800a0000000.pip eth1: Link is Up - 100Mbps/Full - flow control off

How it is supposed to deal with that?

2. It is not possible to call phylink_create from ndo_init callcack as
it evetually calls sfp_bus_add_upstream which calls rtnl_lock().
As this lock is already taken, it just deadlocks. Is this an unsupported
scenario?

Comments welcome and appreciated,
	ladis