Re: [RFC PATCH 2/3] topology: support node_numa_mem() for determining the fallback node

[Nishanth Aravamudan <nacc@linux.vnet.ibm.com>]

Hi Joonsoo,

On 11.02.2014 [16:42:00 +0900], Joonsoo Kim wrote:
> On Mon, Feb 10, 2014 at 11:13:21AM -0800, Nishanth Aravamudan wrote:
> > Hi Christoph,
> > 
> > On 07.02.2014 [12:51:07 -0600], Christoph Lameter wrote:
> > > Here is a draft of a patch to make this work with memoryless nodes.
> > > 
> > > The first thing is that we modify node_match to also match if we hit an
> > > empty node. In that case we simply take the current slab if its there.
> > > 
> > > If there is no current slab then a regular allocation occurs with the
> > > memoryless node. The page allocator will fallback to a possible node and
> > > that will become the current slab. Next alloc from a memoryless node
> > > will then use that slab.
> > > 
> > > For that we also add some tracking of allocations on nodes that were not
> > > satisfied using the empty_node[] array. A successful alloc on a node
> > > clears that flag.
> > > 
> > > I would rather avoid the empty_node[] array since its global and there may
> > > be thread specific allocation restrictions but it would be expensive to do
> > > an allocation attempt via the page allocator to make sure that there is
> > > really no page available from the page allocator.
> > 
> > With this patch on our test system (I pulled out the numa_mem_id()
> > change, since you Acked Joonsoo's already), on top of 3.13.0 + my
> > kthread locality change + CONFIG_HAVE_MEMORYLESS_NODES + Joonsoo's RFC
> > patch 1):
> > 
> > MemTotal:        8264704 kB
> > MemFree:         5924608 kB
> > ...
> > Slab:            1402496 kB
> > SReclaimable:     102848 kB
> > SUnreclaim:      1299648 kB
> > 
> > And Anton's slabusage reports:
> > 
> > slab                                   mem     objs    slabs
> >                                       used   active   active
> > ------------------------------------------------------------
> > kmalloc-16384                       207 MB   98.60%  100.00%
> > task_struct                         134 MB   97.82%  100.00%
> > kmalloc-8192                        117 MB  100.00%  100.00%
> > pgtable-2^12                        111 MB  100.00%  100.00%
> > pgtable-2^10                        104 MB  100.00%  100.00%
> > 
> > For comparison, Anton's patch applied at the same point in the series:
> > 
> > meminfo:
> > 
> > MemTotal:        8264704 kB
> > MemFree:         4150464 kB
> > ...
> > Slab:            1590336 kB
> > SReclaimable:     208768 kB
> > SUnreclaim:      1381568 kB
> > 
> > slabusage:
> > 
> > slab                                   mem     objs    slabs
> >                                       used   active   active
> > ------------------------------------------------------------
> > kmalloc-16384                       227 MB   98.63%  100.00%
> > kmalloc-8192                        130 MB  100.00%  100.00%
> > task_struct                         129 MB   97.73%  100.00%
> > pgtable-2^12                        112 MB  100.00%  100.00%
> > pgtable-2^10                        106 MB  100.00%  100.00%
> > 
> > 
> > Consider this patch:
> > 
> > Acked-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
> > Tested-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
> 
> Hello,
> 
> I still think that there is another problem.
> Your report about CONFIG_SLAB said that SLAB uses just 200MB.
> Below is your previous report.
> 
>   Ok, with your patches applied and CONFIG_SLAB enabled:
> 
>   MemTotal:        8264640 kB
>   MemFree:         7119680 kB
>   Slab:             207232 kB
>   SReclaimable:      32896 kB
>   SUnreclaim:       174336 kB
> 
> The number on CONFIG_SLUB with these patches tell us that SLUB uses 1.4GB.
> There is large difference on slab usage.

Agreed. But, at least for now, this gets us to not OOM all the time :) I
think that's significant progress. I will continue to look at this
issue for where the other gaps are, but would like to see Christoph's
latest patch get merged (pending my re-testing).

> And, I should note that number of active objects on slabinfo can be
> wrong on some situation, since it doesn't consider cpu slab (and cpu
> partial slab).

Well, I grabbed everything from /sys/kernel/slab for you in the
tarballs, I believe.

> I recommend to confirm page_to_nid() and other things as I mentioned
> earlier.

I believe these all work once CONFIG_HAVE_MEMORYLESS_NODES was set for
ppc64, but will test it again when I have access to the test system.

Also, given that only ia64 and (hopefuly soon) ppc64 can set
CONFIG_HAVE_MEMORYLESS_NODES, does that mean x86_64 can't have
memoryless nodes present? Even with fakenuma? Just curious.

-Nish

--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@kvack.org.  For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"dont@kvack.org"> email@kvack.org </a>