From: Ric Mason <ric.masonn@gmail.com>
To: Mel Gorman <mgorman@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>,
Jerome Marchand <jmarchan@redhat.com>,
"linux-mm@kvack.org" <linux-mm@kvack.org>,
linux-kernel <linux-kernel@vger.kernel.org>,
Hugh Dickins <hughd@google.com>
Subject: Re: [PATCH] mm: swap: Mark swap pages writeback before queueing for direct IO
Date: Wed, 01 May 2013 14:58:03 +0800 [thread overview]
Message-ID: <5180BCFB.6090707@gmail.com> (raw)
In-Reply-To: <20130424185744.GB2144@suse.de>
Hi Mel,
On 04/25/2013 02:57 AM, Mel Gorman wrote:
> As pointed out by Andrew Morton, the swap-over-NFS writeback is not setting
> PageWriteback before it is queued for direct IO. While swap pages do not
Before commit commit 62c230bc1 (mm: add support for a filesystem to
activate swap files and use direct_IO for writing swap pages), swap
pages will write to page cache firstly and then writeback?
> participate in BDI or process dirty accounting and the IO is synchronous,
> the writeback bit is still required and not setting it in this case was
> an oversight. swapoff depends on the page writeback to synchronoise all
> pending writes on a swap page before it is reused. Swapcache freeing and
> reuse depend on checking the PageWriteback under lock to ensure the page
> is safe to reuse.
>
> Direct IO handlers and the direct IO handler for NFS do not deal with
> PageWriteback as they are synchronous writes. In the case of NFS, it
> schedules pages (or a page in the case of swap) for IO and then waits
> synchronously for IO to complete in nfs_direct_write(). It is recognised
> that this is a slowdown from normal swap handling which is asynchronous
> and uses a completion handler. Shoving PageWriteback handling down into
> direct IO handlers looks like a bad fit to handle the swap case although
> it may have to be dealt with some day if swap is converted to use direct
> IO in general and bmap is finally done away with. At that point it will
> be necessary to refit asynchronous direct IO with completion handlers onto
> the swap subsystem.
>
> As swapcache currently depends on PageWriteback to protect against races,
> this patch sets PageWriteback under the page lock before queueing it for
> direct IO. It is cleared when the direct IO handler returns. IO errors
> are treated similarly to the direct-to-bio case except PageError is not
> set as in the case of swap-over-NFS, it is likely to be a transient error.
>
> It was asked what prevents such a page being reclaimed in parallel.
> With this patch applied, such a page will now be skipped (most of the time)
> or blocked until the writeback completes. Reclaim checks PageWriteback
> under the page lock before calling try_to_free_swap and the page lock
> should prevent the page being requeued for IO before it is freed.
>
> This and Jerome's related patch should considered for -stable as far
> back as 3.6 when swap-over-NFS was introduced.
>
> Signed-off-by: Mel Gorman <mgorman@suse.de>
> ---
> mm/page_io.c | 17 +++++++++++++++++
> 1 file changed, 17 insertions(+)
>
> diff --git a/mm/page_io.c b/mm/page_io.c
> index 04ca00d..ec04247 100644
> --- a/mm/page_io.c
> +++ b/mm/page_io.c
> @@ -214,6 +214,7 @@ int swap_writepage(struct page *page, struct writeback_control *wbc)
> kiocb.ki_left = PAGE_SIZE;
> kiocb.ki_nbytes = PAGE_SIZE;
>
> + set_page_writeback(page);
> unlock_page(page);
> ret = mapping->a_ops->direct_IO(KERNEL_WRITE,
> &kiocb, &iov,
> @@ -223,8 +224,24 @@ int swap_writepage(struct page *page, struct writeback_control *wbc)
> count_vm_event(PSWPOUT);
> ret = 0;
> } else {
> + /*
> + * In the case of swap-over-nfs, this can be a
> + * temporary failure if the system has limited
> + * memory for allocating transmit buffers.
> + * Mark the page dirty and avoid
> + * rotate_reclaimable_page but rate-limit the
> + * messages but do not flag PageError like
> + * the normal direct-to-bio case as it could
> + * be temporary.
> + */
> set_page_dirty(page);
> + ClearPageReclaim(page);
> + if (printk_ratelimit()) {
> + pr_err("Write-error on dio swapfile (%Lu)\n",
> + (unsigned long long)page_file_offset(page));
> + }
> }
> + end_page_writeback(page);
> return ret;
> }
>
> --
> To unsubscribe, send a message with 'unsubscribe linux-mm' in
> the body to majordomo@kvack.org. For more info on Linux MM,
> see: http://www.linux-mm.org/ .
> Don't email: <a href=mailto:"dont@kvack.org"> email@kvack.org </a>
--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@kvack.org. For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"dont@kvack.org"> email@kvack.org </a>
next prev parent reply other threads:[~2013-05-01 6:58 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-04-17 12:11 [PATCH] swap: redirty page if page write fails on swap file Jerome Marchand
2013-04-17 15:07 ` Johannes Weiner
2013-04-17 15:08 ` Mel Gorman
2013-04-18 0:13 ` Simon Jeons
2013-05-01 7:39 ` Simon Jeons
2013-05-03 9:12 ` Jerome Marchand
2013-04-22 20:37 ` Andrew Morton
2013-04-24 9:57 ` Jerome Marchand
2013-05-01 7:38 ` Will Huck
2013-04-24 18:57 ` [PATCH] mm: swap: Mark swap pages writeback before queueing for direct IO Mel Gorman
2013-04-24 19:23 ` Andrew Morton
2013-04-25 8:53 ` Mel Gorman
2013-05-01 6:58 ` Ric Mason [this message]
2013-05-01 8:20 ` Mel Gorman
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=5180BCFB.6090707@gmail.com \
--to=ric.masonn@gmail.com \
--cc=akpm@linux-foundation.org \
--cc=hughd@google.com \
--cc=jmarchan@redhat.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mm@kvack.org \
--cc=mgorman@suse.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).