From: "Jaehoon Chung" <jh80.chung@samsung.com>
To: "'Adrian Hunter'" <adrian.hunter@intel.com>, <linux-mmc@vger.kernel.org>
Cc: <ulf.hansson@linaro.org>
Subject: RE: [PATCH V2] mmc: sdhci-of_dwcmshc: Change to dwcmshc_phy_init for reusing codes
Date: Tue, 14 Jan 2025 07:48:56 +0900 [thread overview]
Message-ID: <000001db660d$53f08040$fbd180c0$@samsung.com> (raw)
In-Reply-To: <9e244402-7e1a-4799-a159-b940547b4085@intel.com>
> -----Original Message-----
> From: Adrian Hunter <adrian.hunter@intel.com>
> Sent: Wednesday, January 8, 2025 10:52 PM
>
> On 16/12/24 12:51, Jaehoon Chung wrote:
> > dwcmshc_phy_1_8v_init and dwcmshc_phy_3_3v_init differ only by a few
> > lines of code. This allow us to reuse code depending on voltage.
> >
> > Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
> > ---
> > Changelog V2:
> > - Add more conditions to clarify if it's MMC_SIGNAL_VOLTAGE_180
> > - Order the local variable according to Adrian's comment
> > - Use local variable to make more readable
> > ---
> > drivers/mmc/host/sdhci-of-dwcmshc.c | 75 +++++++----------------------
> > 1 file changed, 18 insertions(+), 57 deletions(-)
> >
> > diff --git a/drivers/mmc/host/sdhci-of-dwcmshc.c b/drivers/mmc/host/sdhci-of-dwcmshc.c
> > index 7ea3da45db32..08a9b963fb1a 100644
> > --- a/drivers/mmc/host/sdhci-of-dwcmshc.c
> > +++ b/drivers/mmc/host/sdhci-of-dwcmshc.c
> > @@ -328,12 +328,18 @@ static void dwcmshc_request(struct mmc_host *mmc, struct mmc_request *mrq)
> > sdhci_request(mmc, mrq);
> > }
> >
> > -static void dwcmshc_phy_1_8v_init(struct sdhci_host *host)
> > +static void dwcmshc_phy_init(struct sdhci_host *host)
> > {
> > struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> > struct dwcmshc_priv *priv = sdhci_pltfm_priv(pltfm_host);
> > + u32 rxsel = PHY_PAD_RXSEL_3V3;
> > u32 val;
> >
> > + if (priv->flags & FLAG_IO_FIXED_1V8 ||
> > + (host->mmc->ios.timing & MMC_SIGNAL_VOLTAGE_180 &&
> > + host->flags & SDHCI_SIGNALING_180))
>
> Thanks for making the changes. It looks like
> "&& host->flags & SDHCI_SIGNALING_180" is not needed
Will check after changing your suggestion.
>
> > + rxsel = PHY_PAD_RXSEL_1V8;
> > +
> > /* deassert phy reset & set tx drive strength */
> > val = PHY_CNFG_RSTN_DEASSERT;
> > val |= FIELD_PREP(PHY_CNFG_PAD_SP_MASK, PHY_CNFG_PAD_SP);
> > @@ -353,7 +359,7 @@ static void dwcmshc_phy_1_8v_init(struct sdhci_host *host)
> > sdhci_writeb(host, val, PHY_SDCLKDL_CNFG_R);
> >
> > /* configure phy pads */
> > - val = PHY_PAD_RXSEL_1V8;
> > + val = rxsel;
> > val |= FIELD_PREP(PHY_PAD_WEAKPULL_MASK, PHY_PAD_WEAKPULL_PULLUP);
> > val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_P_MASK, PHY_PAD_TXSLEW_CTRL_P);
> > val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_N_MASK, PHY_PAD_TXSLEW_CTRL_N);
> > @@ -365,65 +371,24 @@ static void dwcmshc_phy_1_8v_init(struct sdhci_host *host)
> > val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_N_MASK, PHY_PAD_TXSLEW_CTRL_N);
> > sdhci_writew(host, val, PHY_CLKPAD_CNFG_R);
> >
> > - val = PHY_PAD_RXSEL_1V8;
> > + val = rxsel;
> > val |= FIELD_PREP(PHY_PAD_WEAKPULL_MASK, PHY_PAD_WEAKPULL_PULLDOWN);
> > val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_P_MASK, PHY_PAD_TXSLEW_CTRL_P);
> > val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_N_MASK, PHY_PAD_TXSLEW_CTRL_N);
> > sdhci_writew(host, val, PHY_STBPAD_CNFG_R);
> >
> > /* enable data strobe mode */
> > - sdhci_writeb(host, FIELD_PREP(PHY_DLLDL_CNFG_SLV_INPSEL_MASK, PHY_DLLDL_CNFG_SLV_INPSEL),
> > - PHY_DLLDL_CNFG_R);
> > -
> > - /* enable phy dll */
> > - sdhci_writeb(host, PHY_DLL_CTRL_ENABLE, PHY_DLL_CTRL_R);
> > -}
> > -
> > -static void dwcmshc_phy_3_3v_init(struct sdhci_host *host)
> > -{
> > - struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> > - struct dwcmshc_priv *priv = sdhci_pltfm_priv(pltfm_host);
> > - u32 val;
> > -
> > - /* deassert phy reset & set tx drive strength */
> > - val = PHY_CNFG_RSTN_DEASSERT;
> > - val |= FIELD_PREP(PHY_CNFG_PAD_SP_MASK, PHY_CNFG_PAD_SP);
> > - val |= FIELD_PREP(PHY_CNFG_PAD_SN_MASK, PHY_CNFG_PAD_SN);
> > - sdhci_writel(host, val, PHY_CNFG_R);
> > -
> > - /* disable delay line */
> > - sdhci_writeb(host, PHY_SDCLKDL_CNFG_UPDATE, PHY_SDCLKDL_CNFG_R);
> > -
> > - /* set delay line */
> > - sdhci_writeb(host, priv->delay_line, PHY_SDCLKDL_DC_R);
> > - sdhci_writeb(host, PHY_DLL_CNFG2_JUMPSTEP, PHY_DLL_CNFG2_R);
> > -
> > - /* enable delay lane */
> > - val = sdhci_readb(host, PHY_SDCLKDL_CNFG_R);
> > - val &= ~(PHY_SDCLKDL_CNFG_UPDATE);
> > - sdhci_writeb(host, val, PHY_SDCLKDL_CNFG_R);
> > + if (priv->flags & FLAG_IO_FIXED_1V8 ||
> > + (host->mmc->ios.timing & MMC_SIGNAL_VOLTAGE_180 &&
> > + host->flags & SDHCI_SIGNALING_180)) {
>
> Probably neater to check rxsel e.g.
>
> if (rxcel == PHY_PAD_RXSEL_1V8) {
Got it. Thanks!
Best Regards,
Jaehoon Chung
>
> > + u8 sel = FIELD_PREP(PHY_DLLDL_CNFG_SLV_INPSEL_MASK, PHY_DLLDL_CNFG_SLV_INPSEL);
> >
> > - /* configure phy pads */
> > - val = PHY_PAD_RXSEL_3V3;
> > - val |= FIELD_PREP(PHY_PAD_WEAKPULL_MASK, PHY_PAD_WEAKPULL_PULLUP);
> > - val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_P_MASK, PHY_PAD_TXSLEW_CTRL_P);
> > - val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_N_MASK, PHY_PAD_TXSLEW_CTRL_N);
> > - sdhci_writew(host, val, PHY_CMDPAD_CNFG_R);
> > - sdhci_writew(host, val, PHY_DATAPAD_CNFG_R);
> > - sdhci_writew(host, val, PHY_RSTNPAD_CNFG_R);
> > -
> > - val = FIELD_PREP(PHY_PAD_TXSLEW_CTRL_P_MASK, PHY_PAD_TXSLEW_CTRL_P);
> > - val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_N_MASK, PHY_PAD_TXSLEW_CTRL_N);
> > - sdhci_writew(host, val, PHY_CLKPAD_CNFG_R);
> > -
> > - val = PHY_PAD_RXSEL_3V3;
> > - val |= FIELD_PREP(PHY_PAD_WEAKPULL_MASK, PHY_PAD_WEAKPULL_PULLDOWN);
> > - val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_P_MASK, PHY_PAD_TXSLEW_CTRL_P);
> > - val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_N_MASK, PHY_PAD_TXSLEW_CTRL_N);
> > - sdhci_writew(host, val, PHY_STBPAD_CNFG_R);
> > + sdhci_writeb(host, sel, PHY_DLLDL_CNFG_R);
> > + }
> >
> > /* enable phy dll */
> > sdhci_writeb(host, PHY_DLL_CTRL_ENABLE, PHY_DLL_CTRL_R);
> > +
> > }
> >
> > static void th1520_sdhci_set_phy(struct sdhci_host *host)
> > @@ -433,11 +398,7 @@ static void th1520_sdhci_set_phy(struct sdhci_host *host)
> > u32 emmc_caps = MMC_CAP2_NO_SD | MMC_CAP2_NO_SDIO;
> > u16 emmc_ctrl;
> >
> > - /* Before power on, set PHY configs */
> > - if (priv->flags & FLAG_IO_FIXED_1V8)
> > - dwcmshc_phy_1_8v_init(host);
> > - else
> > - dwcmshc_phy_3_3v_init(host);
> > + dwcmshc_phy_init(host);
> >
> > if ((host->mmc->caps2 & emmc_caps) == emmc_caps) {
> > emmc_ctrl = sdhci_readw(host, priv->vendor_specific_area1 + DWCMSHC_EMMC_CONTROL);
> > @@ -1163,7 +1124,7 @@ static const struct sdhci_ops sdhci_dwcmshc_th1520_ops = {
> > .get_max_clock = dwcmshc_get_max_clock,
> > .reset = th1520_sdhci_reset,
> > .adma_write_desc = dwcmshc_adma_write_desc,
> > - .voltage_switch = dwcmshc_phy_1_8v_init,
> > + .voltage_switch = dwcmshc_phy_init,
> > .platform_execute_tuning = th1520_execute_tuning,
> > };
> >
>
prev parent reply other threads:[~2025-01-13 22:49 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <CGME20241216105129epcas1p4f1ffe80586e9f7d4e4b5f7653dfde883@epcas1p4.samsung.com>
2024-12-16 10:51 ` [PATCH V2] mmc: sdhci-of_dwcmshc: Change to dwcmshc_phy_init for reusing codes Jaehoon Chung
2025-01-08 13:52 ` Adrian Hunter
2025-01-13 22:48 ` Jaehoon Chung [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='000001db660d$53f08040$fbd180c0$@samsung.com' \
--to=jh80.chung@samsung.com \
--cc=adrian.hunter@intel.com \
--cc=linux-mmc@vger.kernel.org \
--cc=ulf.hansson@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).