* [PATCH] mmc: core: add a power cycle when CMD11 fails [not found] <CGME20210210051209epcas1p3e55c0cbab7313731bc6e425da6189bb4@epcas1p3.samsung.com> @ 2021-02-10 4:59 ` DooHyun Hwang 2021-02-25 7:43 ` DooHyun Hwang 2021-03-02 10:38 ` Ulf Hansson 0 siblings, 2 replies; 7+ messages in thread From: DooHyun Hwang @ 2021-02-10 4:59 UTC (permalink / raw) To: linux-mmc, linux-kernel, ulf.hansson, ebiggers, wsa+renesas, satyat, ludovic.barre, linus.walleij Cc: grant.jung, jt77.jang, junwoo80.lee, jangsub.yi, sh043.lee, cw9316.lee, sh8267.baek, wkon.kim, DooHyun Hwang A power cycle is required if CMD11 fails. CMD11 failure should be handled as no response. If there is a timeout error that means no response to the CMD11, do not send the CMD11 again and the power cycle is required. Any other errors for CMD11 are the same because CMD11 failed. On some bad SD Card, CMD11 may fail but the card may have already invoked the voltage switch sequence. In this case, it is necessary to retry without voltage switching after power cycle. Signed-off-by: DooHyun Hwang <dh0421.hwang@samsung.com> --- drivers/mmc/core/core.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c index 1136b859ddd8..a6674df2a7bb 100644 --- a/drivers/mmc/core/core.c +++ b/drivers/mmc/core/core.c @@ -1207,7 +1207,7 @@ int mmc_set_uhs_voltage(struct mmc_host *host, u32 ocr) err = mmc_wait_for_cmd(host, &cmd, 0); if (err) - return err; + goto power_cycle; if (!mmc_host_is_spi(host) && (cmd.resp[0] & R1_ERROR)) return -EIO; -- 2.29.0 ^ permalink raw reply related [flat|nested] 7+ messages in thread
* RE: [PATCH] mmc: core: add a power cycle when CMD11 fails 2021-02-10 4:59 ` [PATCH] mmc: core: add a power cycle when CMD11 fails DooHyun Hwang @ 2021-02-25 7:43 ` DooHyun Hwang 2021-03-02 10:38 ` Ulf Hansson 1 sibling, 0 replies; 7+ messages in thread From: DooHyun Hwang @ 2021-02-25 7:43 UTC (permalink / raw) To: linux-mmc, linux-kernel, ulf.hansson, ebiggers, wsa+renesas, satyat, ludovic.barre, linus.walleij Cc: grant.jung, jt77.jang, junwoo80.lee, jangsub.yi, sh043.lee, cw9316.lee, sh8267.baek, wkon.kim Dear Maintainers and commiters. Please review this patch for updating. Thanks and regards. DooHyun Hwang. On 17/02/10 4:59 am, DooHyun Hwang wrote: >Subject: [PATCH] mmc: core: add a power cycle when CMD11 fails > >A power cycle is required if CMD11 fails. >CMD11 failure should be handled as no response. > >If there is a timeout error that means no response to the CMD11, do not >send the CMD11 again and the power cycle is required. >Any other errors for CMD11 are the same because CMD11 failed. > >On some bad SD Card, CMD11 may fail but the card may have already invoked >the voltage switch sequence. >In this case, it is necessary to retry without voltage switching after >power cycle. > >Signed-off-by: DooHyun Hwang <dh0421.hwang@samsung.com> ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH] mmc: core: add a power cycle when CMD11 fails 2021-02-10 4:59 ` [PATCH] mmc: core: add a power cycle when CMD11 fails DooHyun Hwang 2021-02-25 7:43 ` DooHyun Hwang @ 2021-03-02 10:38 ` Ulf Hansson 2021-03-03 6:30 ` DooHyun Hwang 2021-03-03 6:39 ` DooHyun Hwang 1 sibling, 2 replies; 7+ messages in thread From: Ulf Hansson @ 2021-03-02 10:38 UTC (permalink / raw) To: DooHyun Hwang Cc: linux-mmc@vger.kernel.org, Linux Kernel Mailing List, Eric Biggers, Wolfram Sang, Satya Tangirala, Ludovic Barre, Linus Walleij, grant.jung, jt77.jang, junwoo80.lee, jangsub.yi, sh043.lee, Chanwoo Lee, sh8267.baek, wkon.kim On Wed, 10 Feb 2021 at 06:12, DooHyun Hwang <dh0421.hwang@samsung.com> wrote: > > A power cycle is required if CMD11 fails. > CMD11 failure should be handled as no response. > > If there is a timeout error that means no response to the CMD11, > do not send the CMD11 again and the power cycle is required. > Any other errors for CMD11 are the same because CMD11 failed. > > On some bad SD Card, CMD11 may fail but the card may have already > invoked the voltage switch sequence. > In this case, it is necessary to retry without voltage switching > after power cycle. > > Signed-off-by: DooHyun Hwang <dh0421.hwang@samsung.com> Applied for next, thanks! I took the liberty of updating the commit message a bit, to try to clarify things. Moreover, I have tagged this for stable kernels. BTW, did you try to force the error to -EAGAIN, to keep retrying for a couple of times? If so, did it end up with the same kind of errors? > --- > drivers/mmc/core/core.c | 2 +- > 1 file changed, 1 insertion(+), 1 deletion(-) > > diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c > index 1136b859ddd8..a6674df2a7bb 100644 > --- a/drivers/mmc/core/core.c > +++ b/drivers/mmc/core/core.c > @@ -1207,7 +1207,7 @@ int mmc_set_uhs_voltage(struct mmc_host *host, u32 ocr) > > err = mmc_wait_for_cmd(host, &cmd, 0); > if (err) > - return err; > + goto power_cycle; > > if (!mmc_host_is_spi(host) && (cmd.resp[0] & R1_ERROR)) > return -EIO; > -- > 2.29.0 > Kind regards Uffe ^ permalink raw reply [flat|nested] 7+ messages in thread
* RE: [PATCH] mmc: core: add a power cycle when CMD11 fails 2021-03-02 10:38 ` Ulf Hansson @ 2021-03-03 6:30 ` DooHyun Hwang 2021-03-03 10:59 ` Ulf Hansson 2021-03-03 6:39 ` DooHyun Hwang 1 sibling, 1 reply; 7+ messages in thread From: DooHyun Hwang @ 2021-03-03 6:30 UTC (permalink / raw) To: 'Ulf Hansson' Cc: linux-mmc, 'Linux Kernel Mailing List', 'Eric Biggers', 'Wolfram Sang', 'Satya Tangirala', 'Ludovic Barre', 'Linus Walleij', grant.jung, jt77.jang, junwoo80.lee, jangsub.yi, sh043.lee, 'Chanwoo Lee', sh8267.baek, wkon.kim On Tue, 2 Mar 2021 at 10:38, Ulf Hansson <ulf.hansson@linaro.org> wrote: >On Wed, 10 Feb 2021 at 06:12, DooHyun Hwang <dh0421.hwang@samsung.com> >wrote: >> >> A power cycle is required if CMD11 fails. >> CMD11 failure should be handled as no response. >> >> If there is a timeout error that means no response to the CMD11, do >> not send the CMD11 again and the power cycle is required. >> Any other errors for CMD11 are the same because CMD11 failed. >> >> On some bad SD Card, CMD11 may fail but the card may have already >> invoked the voltage switch sequence. >> In this case, it is necessary to retry without voltage switching after >> power cycle. >> >> Signed-off-by: DooHyun Hwang <dh0421.hwang@samsung.com> > >Applied for next, thanks! > >I took the liberty of updating the commit message a bit, to try to clarify >things. Moreover, I have tagged this for stable kernels. > >BTW, did you try to force the error to -EAGAIN, to keep retrying for a >couple of times? If so, did it end up with the same kind of errors? Thank you for reviewing this. Yes. I tested with 2 SD cards. I think the power cycle is needed before retrying because SD card doesn't respond SD_ROCR_S18A when retrying without power cycle. #1. No change // send ACMD41 + with SD_OCR_S18R (bit[24]) <7>[ 100.852818] [0: kworker/0:0: 5] mmc0: starting CMD41 arg 51040000 flags 000000e1 // resp ACMD41 + with SD_ROCR_S18A (bit[24]) <7>[ 100.853177] I[0: Binder:4670_3: 4705] mmc0: req done (CMD41): 0: c1ff8000 00000000 00000000 00000000 // send CMD11 and error occurs <7>[ 100.853288] [0: kworker/0:0: 5] mmc0: starting CMD11 arg 00000000 flags 00000015 <7>[ 100.854009] I[0: Binder:4670_3: 4705] mmc0: req done (CMD11): -84: 00000000 00000000 00000000 00000000 // clear SD_OCR_S18R <4>[ 100.854145] [0: kworker/0:0: 5] mmc0: Skipping voltage switch <7>[ 100.854179] [0: kworker/0:0: 5] mmc0: clock 400000Hz busmode 2 powermode 2 cs 1 Vdd 18 width 1 timing 0 <7>[ 100.855651] [0: kworker/0:0: 5] mmc0: starting CMD0 arg 00000000 flags 000000c0 <7>[ 100.855868] I[0: Binder:4670_3: 4705] mmc0: req done (CMD0): 0: 00000000 00000000 00000000 00000000 <7>[ 100.857234] [0: kworker/0:0: 5] mmc0: clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 18 width 1 timing 0 <7>[ 100.858638] [0: kworker/0:0: 5] mmc0: starting CMD8 arg 000001aa flags 000002f5 <7>[ 100.859100] I[0: Binder:4670_3: 4705] mmc0: req done (CMD8): -84: 00000000 00000000 00000000 00000000 <7>[ 100.859607] [0: kworker/0:0: 5] mmc0: starting CMD55 arg 00000000 flags 000000f5 <7>[ 100.860098] I[0: Binder:4670_3: 4705] mmc0: req done (CMD55): -84: 00000000 00000000 00000000 00000000 ... <3>[ 100.861846] [0: kworker/0:0: 5] mmc0: error -84 whilst initialising SD card #2. I tried to force the error to -EAGAIN(without power cycle), has confirmed that the normal operation but card responded without SD_ROCR_S18A from ACMD41 So, Voltage Switching was skipped and the SD card initialized to HS mode. // send ACMD41 + with SD_OCR_S18R (bit[24]) <7>[ 117.525089] [0: kworker/0:2: 375] mmc0: starting CMD41 arg 51040000 flags 000000e1 // resp ACMD41 + with SD_ROCR_S18A (bit[24]) <7>[ 117.525438] I[0:id.app.reminder: 8908] mmc0: req done (CMD41): 0: c1ff8000 00000000 00000000 00000000 // send CMD11 and complete <7>[ 117.525505] [0: kworker/0:2: 375] mmc0: starting CMD11 arg 00000000 flags 00000015 <7>[ 117.525866] I[0:id.app.reminder: 8908] mmc0: req done (CMD11): 0: 00000320 00000000 00000000 00000000 <7>[ 117.527296] [0: kworker/0:2: 375] mmc0: clock 0Hz busmode 2 powermode 2 cs 0 Vdd 18 width 1 timing 0 <7>[ 117.540116] [0: kworker/0:2: 375] mmc0: clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 18 width 1 timing 0 // set -EAGAIN <3>[ 117.541650] [0: kworker/0:2: 375] mmc_sd_get_cid: rocr=0xc1ff8000, retries=10. err=0 -> -11. // retry without power cycle <7>[ 117.541683] [0: kworker/0:2: 375] mmc0: clock 400000Hz busmode 2 powermode 2 cs 1 Vdd 18 width 1 timing 0 <7>[ 117.543106] [0: kworker/0:2: 375] mmc0: starting CMD0 arg 00000000 flags 000000c0 <7>[ 117.543323] I[0:id.app.reminder: 8908] mmc0: req done (CMD0): 0: 00000000 00000000 00000000 00000000 <7>[ 117.544679] [0: kworker/0:2: 375] mmc0: clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 18 width 1 timing 0 <7>[ 117.546131] [0: kworker/0:2: 375] mmc0: starting CMD8 arg 000001aa flags 000002f5 <7>[ 117.546484] I[0:id.app.reminder: 8908] mmc0: req done (CMD8): 0: 000001aa 00000000 00000000 00000000 // send ACMD41 + with SD_OCR_S18R (bit[24]) <7>[ 117.559967] [0: kworker/0:2: 375] mmc0: starting CMD55 arg 00000000 flags 000000f5 <7>[ 117.560445] I[0: ksoftirqd/0: 10] mmc0: req done (CMD55): 0: 00000120 00000000 00000000 00000000 <7>[ 117.560505] [0: kworker/0:2: 375] mmc0: starting CMD41 arg 51040000 flags 000000e1 // resp ACMD41 + without SD_ROCR_S18A (bit[24]) <7>[ 117.560853] I[0:Runtime worker : 8942] mmc0: req done (CMD41): 0: c0ff8000 00000000 00000000 00000000 <7>[ 117.562093] [0: kworker/0:2: 375] mmc0: starting CMD2 arg 00000000 flags 00000007 #3. Forced set error of CMD11 and the SD card initialized to HS mode. // send ACMD41 + with SD_OCR_S18R (bit[24]) <7>[ 115.040643] [0: kworker/0:2: 690] mmc0: starting CMD41 arg 51040000 flags 000000e1 // resp ACMD41 + with SD_ROCR_S18A (bit[24]) <7>[ 115.040990] I[0:Jit thread pool: 8904] mmc0: req done (CMD41): 0: c1ff8000 00000000 00000000 00000000 // send CMD11 and error occurs <7>[ 115.041092] [0: kworker/0:2: 690] mmc0: starting CMD11 arg 00000000 flags 00000015 <7>[ 115.041789] I[0:Jit thread pool: 8904] mmc0: req done (CMD11): -84: 00000000 00000000 00000000 00000000 // retry with power cycle (tested with this patch) <7>[ 115.041855] [0: kworker/0:2: 690] mmc0: Signal voltage switch failed, power cycling card <7>[ 115.041898] [0: kworker/0:2: 690] mmc0: clock 0Hz busmode 2 powermode 0 cs 0 Vdd 0 width 1 timing 0 <7>[ 115.045922] [0: kworker/0:2: 690] mmc0: clock 0Hz busmode 2 powermode 1 cs 0 Vdd 18 width 1 timing 0 <7>[ 115.064130] [0: kworker/0:2: 690] mmc0: clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 18 width 1 timing 0 // return error and retry after (retries = 0;) <3>[ 115.076912] [0: kworker/0:2: 690] mmc_sd_get_cid: rocr=0xc1ff8000, retries=10. err=-84. // clear SD_OCR_S18R <4>[ 115.076943] [0: kworker/0:2: 690] mmc0: Skipping voltage switch <7>[ 115.076973] [0: kworker/0:2: 690] mmc0: clock 400000Hz busmode 2 powermode 2 cs 1 Vdd 18 width 1 timing 0 <7>[ 115.078375] [0: kworker/0:2: 690] mmc0: starting CMD0 arg 00000000 flags 000000c0 <7>[ 115.078617] I[0: swapper/0: 0] mmc0: req done (CMD0): 0: 00000000 00000000 00000000 00000000 <7>[ 115.079980] [0: kworker/0:2: 690] mmc0: clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 18 width 1 timing 0 <7>[ 115.081506] [0: kworker/0:2: 690] mmc0: starting CMD8 arg 000001aa flags 000002f5 <7>[ 115.081868] I[0: swapper/0: 0] mmc0: req done (CMD8): 0: 000001aa 00000000 00000000 00000000 // send ACMD41 + without SD_OCR_S18R (bit[24]) <7>[ 115.190656] [0: kworker/0:2: 690] mmc0: starting CMD55 arg 00000000 flags 000000f5 <7>[ 115.191046] I[0:Jit thread pool: 4475] mmc0: req done (CMD55): 0: 00000120 00000000 00000000 00000000 <7>[ 115.191113] [0: kworker/0:2: 690] mmc0: starting CMD41 arg 50040000 flags 000000e1 // resp ACMD41 + without SD_ROCR_S18A (bit[24]) <7>[ 115.191474] I[0:Jit thread pool: 4475] mmc0: req done (CMD41): 0: c0ff8000 00000000 00000000 00000000 <7>[ 115.191541] [0: kworker/0:2: 690] mmc0: starting CMD2 arg 00000000 flags 00000007 #4. SD card responded with SD_ROCR_S18A from ACMD41 after power cycle, and change CMD11's error value to -EAGAIN // send ACMD41 + with SD_OCR_S18R (bit[24]) <7>[ 156.884623] [0: kworker/0:1: 7] mmc0: starting CMD41 arg 51040000 flags 000000e1 // resp ACMD41 + with SD_ROCR_S18A (bit[24]) <7>[ 156.884975] I[0: highpool[3]: 5440] mmc0: req done (CMD41): 0: c1ff8000 00000000 00000000 00000000 // send CMD11 and error occurs <7>[ 156.885051] [0: kworker/0:1: 7] mmc0: starting CMD11 arg 00000000 flags 00000015 <7>[ 156.885759] I[0: highpool[3]: 5440] mmc0: req done (CMD11): -84: 00000000 00000000 00000000 00000000 // retry with power cycle (tested with this patch) <7>[ 156.885834] [0: kworker/0:1: 7] mmc0: Signal voltage switch failed, power cycling card <7>[ 156.885875] [0: kworker/0:1: 7] mmc0: clock 0Hz busmode 2 powermode 0 cs 0 Vdd 0 width 1 timing 0 <7>[ 156.920185] [0: kworker/0:1: 7] mmc0: clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 18 width 1 timing 0 // change CMD11's error value to -EAGAIN <3>[ 156.932288] [0: kworker/0:1: 7] mmc_sd_get_cid: rocr=0xc1ff8000, retries=10. err=-84 -> -11. <7>[ 156.932336] [0: kworker/0:1: 7] mmc0: clock 400000Hz busmode 2 powermode 2 cs 1 Vdd 18 width 1 timing 0 <7>[ 156.933834] [0: kworker/0:1: 7] mmc0: starting CMD0 arg 00000000 flags 000000c0 <7>[ 156.934101] I[0:ung.android.mdx:10229] mmc0: req done (CMD0): 0: 00000000 00000000 00000000 00000000 <7>[ 156.935562] [0: kworker/0:1: 7] mmc0: clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 18 width 1 timing 0 <7>[ 156.937009] [0: kworker/0:1: 7] mmc0: starting CMD8 arg 000001aa flags 000002f5 <7>[ 156.937372] I[0:ung.android.mdx:10229] mmc0: req done (CMD8): 0: 000001aa 00000000 00000000 00000000 // send ACMD41 + with SD_OCR_S18R (bit[24]) <7>[ 157.044190] [0: kworker/0:1: 7] mmc0: starting CMD55 arg 00000000 flags 000000f5 <7>[ 157.044924] I[0:ung.android.mdx:10229] mmc0: req done (CMD55): 0: 00000120 00000000 00000000 00000000 <7>[ 157.045023] [0: kworker/0:1: 7] mmc0: starting CMD41 arg 51040000 flags 000000e1 // resp ACMD41 + with SD_ROCR_S18A (bit[24]) <7>[ 157.045389] I[0:ung.android.mdx:10229] mmc0: req done (CMD41): 0: c1ff8000 00000000 00000000 00000000 // send CMD11 and complete <7>[ 157.045467] [0: kworker/0:1: 7] mmc0: starting CMD11 arg 00000000 flags 00000015 <7>[ 157.045855] I[0: Binder:798_2: 805] mmc0: req done (CMD11): 0: 00000320 00000000 00000000 00000000 > >> --- >> drivers/mmc/core/core.c | 2 +- >> 1 file changed, 1 insertion(+), 1 deletion(-) >> >> diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c index >> 1136b859ddd8..a6674df2a7bb 100644 >> --- a/drivers/mmc/core/core.c >> +++ b/drivers/mmc/core/core.c >> @@ -1207,7 +1207,7 @@ int mmc_set_uhs_voltage(struct mmc_host *host, >> u32 ocr) >> >> err = mmc_wait_for_cmd(host, &cmd, 0); >> if (err) >> - return err; >> + goto power_cycle; >> >> if (!mmc_host_is_spi(host) && (cmd.resp[0] & R1_ERROR)) >> return -EIO; >> -- >> 2.29.0 >> > >Kind regards >Uffe Thanks and regards. DooHyun Hwang. ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH] mmc: core: add a power cycle when CMD11 fails 2021-03-03 6:30 ` DooHyun Hwang @ 2021-03-03 10:59 ` Ulf Hansson 2021-03-03 11:29 ` DooHyun Hwang 0 siblings, 1 reply; 7+ messages in thread From: Ulf Hansson @ 2021-03-03 10:59 UTC (permalink / raw) To: DooHyun Hwang Cc: linux-mmc@vger.kernel.org, Linux Kernel Mailing List, Eric Biggers, Wolfram Sang, Satya Tangirala, Ludovic Barre, Linus Walleij, grant.jung, jt77.jang, junwoo80.lee, jangsub.yi, Seunghui Lee, Chanwoo Lee, sh8267.baek, wkon.kim On Wed, 3 Mar 2021 at 07:30, DooHyun Hwang <dh0421.hwang@samsung.com> wrote: > > On Tue, 2 Mar 2021 at 10:38, Ulf Hansson <ulf.hansson@linaro.org> wrote: > >On Wed, 10 Feb 2021 at 06:12, DooHyun Hwang <dh0421.hwang@samsung.com> > >wrote: > >> > >> A power cycle is required if CMD11 fails. > >> CMD11 failure should be handled as no response. > >> > >> If there is a timeout error that means no response to the CMD11, do > >> not send the CMD11 again and the power cycle is required. > >> Any other errors for CMD11 are the same because CMD11 failed. > >> > >> On some bad SD Card, CMD11 may fail but the card may have already > >> invoked the voltage switch sequence. > >> In this case, it is necessary to retry without voltage switching after > >> power cycle. > >> > >> Signed-off-by: DooHyun Hwang <dh0421.hwang@samsung.com> > > > >Applied for next, thanks! > > > >I took the liberty of updating the commit message a bit, to try to clarify > >things. Moreover, I have tagged this for stable kernels. > > > >BTW, did you try to force the error to -EAGAIN, to keep retrying for a > >couple of times? If so, did it end up with the same kind of errors? > > Thank you for reviewing this. > > Yes. I tested with 2 SD cards. > I think the power cycle is needed before retrying > because SD card doesn't respond SD_ROCR_S18A when retrying without power cycle. Thanks for sharing the logs and the details below! If I understand correctly, forcing the error to -EAGAIN combined with the power cycle when the CMD11 fails, actually makes us succeed with the voltage switch in the second retry. Correct? In that case, it seems like a good idea to extend $subject patch to return -EAGAIN in case we get an error from the CMD11, right? [...] > > #4. SD card responded with SD_ROCR_S18A from ACMD41 after power cycle, and change CMD11's error value to -EAGAIN > // send ACMD41 + with SD_OCR_S18R (bit[24]) > <7>[ 156.884623] [0: kworker/0:1: 7] mmc0: starting CMD41 arg 51040000 flags 000000e1 > // resp ACMD41 + with SD_ROCR_S18A (bit[24]) > <7>[ 156.884975] I[0: highpool[3]: 5440] mmc0: req done (CMD41): 0: c1ff8000 00000000 00000000 00000000 > // send CMD11 and error occurs > <7>[ 156.885051] [0: kworker/0:1: 7] mmc0: starting CMD11 arg 00000000 flags 00000015 > <7>[ 156.885759] I[0: highpool[3]: 5440] mmc0: req done (CMD11): -84: 00000000 00000000 00000000 00000000 > // retry with power cycle (tested with this patch) > <7>[ 156.885834] [0: kworker/0:1: 7] mmc0: Signal voltage switch failed, power cycling card > <7>[ 156.885875] [0: kworker/0:1: 7] mmc0: clock 0Hz busmode 2 powermode 0 cs 0 Vdd 0 width 1 timing 0 > <7>[ 156.920185] [0: kworker/0:1: 7] mmc0: clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 18 width 1 timing 0 > // change CMD11's error value to -EAGAIN > <3>[ 156.932288] [0: kworker/0:1: 7] mmc_sd_get_cid: rocr=0xc1ff8000, retries=10. err=-84 -> -11. > <7>[ 156.932336] [0: kworker/0:1: 7] mmc0: clock 400000Hz busmode 2 powermode 2 cs 1 Vdd 18 width 1 timing 0 > <7>[ 156.933834] [0: kworker/0:1: 7] mmc0: starting CMD0 arg 00000000 flags 000000c0 > <7>[ 156.934101] I[0:ung.android.mdx:10229] mmc0: req done (CMD0): 0: 00000000 00000000 00000000 00000000 > <7>[ 156.935562] [0: kworker/0:1: 7] mmc0: clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 18 width 1 timing 0 > <7>[ 156.937009] [0: kworker/0:1: 7] mmc0: starting CMD8 arg 000001aa flags 000002f5 > <7>[ 156.937372] I[0:ung.android.mdx:10229] mmc0: req done (CMD8): 0: 000001aa 00000000 00000000 00000000 > // send ACMD41 + with SD_OCR_S18R (bit[24]) > <7>[ 157.044190] [0: kworker/0:1: 7] mmc0: starting CMD55 arg 00000000 flags 000000f5 > <7>[ 157.044924] I[0:ung.android.mdx:10229] mmc0: req done (CMD55): 0: 00000120 00000000 00000000 00000000 > <7>[ 157.045023] [0: kworker/0:1: 7] mmc0: starting CMD41 arg 51040000 flags 000000e1 > // resp ACMD41 + with SD_ROCR_S18A (bit[24]) > <7>[ 157.045389] I[0:ung.android.mdx:10229] mmc0: req done (CMD41): 0: c1ff8000 00000000 00000000 00000000 > // send CMD11 and complete > <7>[ 157.045467] [0: kworker/0:1: 7] mmc0: starting CMD11 arg 00000000 flags 00000015 > <7>[ 157.045855] I[0: Binder:798_2: 805] mmc0: req done (CMD11): 0: 00000320 00000000 00000000 00000000 > > > > > >> --- > >> drivers/mmc/core/core.c | 2 +- > >> 1 file changed, 1 insertion(+), 1 deletion(-) > >> > >> diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c index > >> 1136b859ddd8..a6674df2a7bb 100644 > >> --- a/drivers/mmc/core/core.c > >> +++ b/drivers/mmc/core/core.c > >> @@ -1207,7 +1207,7 @@ int mmc_set_uhs_voltage(struct mmc_host *host, > >> u32 ocr) > >> > >> err = mmc_wait_for_cmd(host, &cmd, 0); > >> if (err) > >> - return err; > >> + goto power_cycle; > >> > >> if (!mmc_host_is_spi(host) && (cmd.resp[0] & R1_ERROR)) > >> return -EIO; > >> -- > >> 2.29.0 > >> Kind regards Uffe ^ permalink raw reply [flat|nested] 7+ messages in thread
* RE: [PATCH] mmc: core: add a power cycle when CMD11 fails 2021-03-03 10:59 ` Ulf Hansson @ 2021-03-03 11:29 ` DooHyun Hwang 0 siblings, 0 replies; 7+ messages in thread From: DooHyun Hwang @ 2021-03-03 11:29 UTC (permalink / raw) To: 'Ulf Hansson' Cc: linux-mmc, 'Linux Kernel Mailing List', 'Eric Biggers', 'Wolfram Sang', 'Satya Tangirala', 'Ludovic Barre', 'Linus Walleij', grant.jung, jt77.jang, junwoo80.lee, jangsub.yi, 'Seunghui Lee', 'Chanwoo Lee', sh8267.baek, wkon.kim On Wed, 3 Mar 2021 at 12:00, Ulf Hansson <ulf.hansson@linaro.org> wrote: > >On Wed, 3 Mar 2021 at 07:30, DooHyun Hwang <dh0421.hwang@samsung.com> wrote: >> >> On Tue, 2 Mar 2021 at 10:38, Ulf Hansson <ulf.hansson@linaro.org> wrote: >> >On Wed, 10 Feb 2021 at 06:12, DooHyun Hwang >> ><dh0421.hwang@samsung.com> >> >wrote: >> >> >> >> A power cycle is required if CMD11 fails. >> >> CMD11 failure should be handled as no response. >> >> >> >> If there is a timeout error that means no response to the CMD11, do >> >> not send the CMD11 again and the power cycle is required. >> >> Any other errors for CMD11 are the same because CMD11 failed. >> >> >> >> On some bad SD Card, CMD11 may fail but the card may have already >> >> invoked the voltage switch sequence. >> >> In this case, it is necessary to retry without voltage switching >> >> after power cycle. >> >> >> >> Signed-off-by: DooHyun Hwang <dh0421.hwang@samsung.com> >> > >> >Applied for next, thanks! >> > >> >I took the liberty of updating the commit message a bit, to try to >> >clarify things. Moreover, I have tagged this for stable kernels. >> > >> >BTW, did you try to force the error to -EAGAIN, to keep retrying for >> >a couple of times? If so, did it end up with the same kind of errors? >> >> Thank you for reviewing this. >> >> Yes. I tested with 2 SD cards. >> I think the power cycle is needed before retrying because SD card >> doesn't respond SD_ROCR_S18A when retrying without power cycle. > >Thanks for sharing the logs and the details below! > >If I understand correctly, forcing the error to -EAGAIN combined with the >power cycle when the CMD11 fails, actually makes us succeed with the >voltage switch in the second retry. Correct? Yes, That's right. > >In that case, it seems like a good idea to extend $subject patch to return >-EAGAIN in case we get an error from the CMD11, right? Yes, I think so. But it looks good to retry CMD11 only for a couple of times, and if it still fails, it would be better to remove SD_OCR_S18R and retry ACMD41 as before. > >[...] > >> >> #4. SD card responded with SD_ROCR_S18A from ACMD41 after power cycle, >> and change CMD11's error value to -EAGAIN // send ACMD41 + with >SD_OCR_S18R (bit[24]) >> <7>[ 156.884623] [0: kworker/0:1: 7] mmc0: starting CMD41 arg >51040000 flags 000000e1 >> // resp ACMD41 + with SD_ROCR_S18A (bit[24]) >> <7>[ 156.884975] I[0: highpool[3]: 5440] mmc0: req done (CMD41): 0: >c1ff8000 00000000 00000000 00000000 >> // send CMD11 and error occurs >> <7>[ 156.885051] [0: kworker/0:1: 7] mmc0: starting CMD11 arg >00000000 flags 00000015 >> <7>[ 156.885759] I[0: highpool[3]: 5440] mmc0: req done (CMD11): -84: >00000000 00000000 00000000 00000000 >> // retry with power cycle (tested with this patch) >> <7>[ 156.885834] [0: kworker/0:1: 7] mmc0: Signal voltage switch >failed, power cycling card >> <7>[ 156.885875] [0: kworker/0:1: 7] mmc0: clock 0Hz busmode 2 >powermode 0 cs 0 Vdd 0 width 1 timing 0 >> <7>[ 156.920185] [0: kworker/0:1: 7] mmc0: clock 400000Hz busmode 2 >powermode 2 cs 0 Vdd 18 width 1 timing 0 >> // change CMD11's error value to -EAGAIN >> <3>[ 156.932288] [0: kworker/0:1: 7] mmc_sd_get_cid: rocr=0xc1ff8000, >retries=10. err=-84 -> -11. >> <7>[ 156.932336] [0: kworker/0:1: 7] mmc0: clock 400000Hz busmode 2 >powermode 2 cs 1 Vdd 18 width 1 timing 0 >> <7>[ 156.933834] [0: kworker/0:1: 7] mmc0: starting CMD0 arg >00000000 flags 000000c0 >> <7>[ 156.934101] I[0:ung.android.mdx:10229] mmc0: req done (CMD0): 0: >00000000 00000000 00000000 00000000 >> <7>[ 156.935562] [0: kworker/0:1: 7] mmc0: clock 400000Hz busmode 2 >powermode 2 cs 0 Vdd 18 width 1 timing 0 >> <7>[ 156.937009] [0: kworker/0:1: 7] mmc0: starting CMD8 arg >000001aa flags 000002f5 >> <7>[ 156.937372] I[0:ung.android.mdx:10229] mmc0: req done (CMD8): 0: >> 000001aa 00000000 00000000 00000000 // send ACMD41 + with SD_OCR_S18R >(bit[24]) >> <7>[ 157.044190] [0: kworker/0:1: 7] mmc0: starting CMD55 arg >00000000 flags 000000f5 >> <7>[ 157.044924] I[0:ung.android.mdx:10229] mmc0: req done (CMD55): 0: >00000120 00000000 00000000 00000000 >> <7>[ 157.045023] [0: kworker/0:1: 7] mmc0: starting CMD41 arg >51040000 flags 000000e1 >> // resp ACMD41 + with SD_ROCR_S18A (bit[24]) <7>[ 157.045389] >> I[0:ung.android.mdx:10229] mmc0: req done (CMD41): 0: c1ff8000 >> 00000000 00000000 00000000 // send CMD11 and complete >> <7>[ 157.045467] [0: kworker/0:1: 7] mmc0: starting CMD11 arg >00000000 flags 00000015 >> <7>[ 157.045855] I[0: Binder:798_2: 805] mmc0: req done (CMD11): 0: >00000320 00000000 00000000 00000000 >> >> >> > >> >> --- >> >> drivers/mmc/core/core.c | 2 +- >> >> 1 file changed, 1 insertion(+), 1 deletion(-) >> >> >> >> diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c >> >> index 1136b859ddd8..a6674df2a7bb 100644 >> >> --- a/drivers/mmc/core/core.c >> >> +++ b/drivers/mmc/core/core.c >> >> @@ -1207,7 +1207,7 @@ int mmc_set_uhs_voltage(struct mmc_host >> >> *host, >> >> u32 ocr) >> >> >> >> err = mmc_wait_for_cmd(host, &cmd, 0); >> >> if (err) >> >> - return err; >> >> + goto power_cycle; >> >> >> >> if (!mmc_host_is_spi(host) && (cmd.resp[0] & R1_ERROR)) >> >> return -EIO; >> >> -- >> >> 2.29.0 >> >> > >Kind regards >Uffe Thanks and regards. DooHyun Hwang. ^ permalink raw reply [flat|nested] 7+ messages in thread
* RE: [PATCH] mmc: core: add a power cycle when CMD11 fails 2021-03-02 10:38 ` Ulf Hansson 2021-03-03 6:30 ` DooHyun Hwang @ 2021-03-03 6:39 ` DooHyun Hwang 1 sibling, 0 replies; 7+ messages in thread From: DooHyun Hwang @ 2021-03-03 6:39 UTC (permalink / raw) To: 'Ulf Hansson' Cc: linux-mmc, 'Linux Kernel Mailing List', 'Eric Biggers', 'Wolfram Sang', 'Satya Tangirala', 'Ludovic Barre', 'Linus Walleij', grant.jung, jt77.jang, junwoo80.lee, jangsub.yi, sh043.lee, 'Chanwoo Lee', sh8267.baek, wkon.kim On Tue, 2 Mar 2021 at 10:38, Ulf Hansson <ulf.hansson@linaro.org> wrote: >On Wed, 10 Feb 2021 at 06:12, DooHyun Hwang <dh0421.hwang@samsung.com> >wrote: >> >> A power cycle is required if CMD11 fails. >> CMD11 failure should be handled as no response. >> >> If there is a timeout error that means no response to the CMD11, do >> not send the CMD11 again and the power cycle is required. >> Any other errors for CMD11 are the same because CMD11 failed. >> >> On some bad SD Card, CMD11 may fail but the card may have already >> invoked the voltage switch sequence. >> In this case, it is necessary to retry without voltage switching after >> power cycle. >> >> Signed-off-by: DooHyun Hwang <dh0421.hwang@samsung.com> > >Applied for next, thanks! > >I took the liberty of updating the commit message a bit, to try to clarify >things. Moreover, I have tagged this for stable kernels. > >BTW, did you try to force the error to -EAGAIN, to keep retrying for a >couple of times? If so, did it end up with the same kind of errors? > Thank you for reviewing this. Yes. I tested with 2 SD cards. I think the power cycle is needed before retrying because SD card doesn't respond SD_ROCR_S18A when retrying without power cycle. #1. No change // send ACMD41 + with SD_OCR_S18R (bit[24]) <7>[ 100.852818] [0: kworker/0:0: 5] mmc0: starting CMD41 arg 51040000 flags 000000e1 // resp ACMD41 + with SD_ROCR_S18A (bit[24]) <7>[ 100.853177] I[0: Binder:4670_3: 4705] mmc0: req done (CMD41): 0: c1ff8000 00000000 00000000 00000000 // send CMD11 and error occurs <7>[ 100.853288] [0: kworker/0:0: 5] mmc0: starting CMD11 arg 00000000 flags 00000015 <7>[ 100.854009] I[0: Binder:4670_3: 4705] mmc0: req done (CMD11): -84: 00000000 00000000 00000000 00000000 // clear SD_OCR_S18R <4>[ 100.854145] [0: kworker/0:0: 5] mmc0: Skipping voltage switch <7>[ 100.854179] [0: kworker/0:0: 5] mmc0: clock 400000Hz busmode 2 powermode 2 cs 1 Vdd 18 width 1 timing 0 <7>[ 100.855651] [0: kworker/0:0: 5] mmc0: starting CMD0 arg 00000000 flags 000000c0 <7>[ 100.855868] I[0: Binder:4670_3: 4705] mmc0: req done (CMD0): 0: 00000000 00000000 00000000 00000000 <7>[ 100.857234] [0: kworker/0:0: 5] mmc0: clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 18 width 1 timing 0 <7>[ 100.858638] [0: kworker/0:0: 5] mmc0: starting CMD8 arg 000001aa flags 000002f5 <7>[ 100.859100] I[0: Binder:4670_3: 4705] mmc0: req done (CMD8): -84: 00000000 00000000 00000000 00000000 <7>[ 100.859607] [0: kworker/0:0: 5] mmc0: starting CMD55 arg 00000000 flags 000000f5 <7>[ 100.860098] I[0: Binder:4670_3: 4705] mmc0: req done (CMD55): -84: 00000000 00000000 00000000 00000000 ... <3>[ 100.861846] [0: kworker/0:0: 5] mmc0: error -84 whilst initialising SD card #2. I tried to force the error to -EAGAIN(without power cycle), has confirmed that the normal operation but card responded without SD_ROCR_S18A from ACMD41 So, Voltage Switching was skipped and the SD card initialized to HS mode. // send ACMD41 + with SD_OCR_S18R (bit[24]) <7>[ 117.525089] [0: kworker/0:2: 375] mmc0: starting CMD41 arg 51040000 flags 000000e1 // resp ACMD41 + with SD_ROCR_S18A (bit[24]) <7>[ 117.525438] I[0:id.app.reminder: 8908] mmc0: req done (CMD41): 0: c1ff8000 00000000 00000000 00000000 // send CMD11 and complete <7>[ 117.525505] [0: kworker/0:2: 375] mmc0: starting CMD11 arg 00000000 flags 00000015 <7>[ 117.525866] I[0:id.app.reminder: 8908] mmc0: req done (CMD11): 0: 00000320 00000000 00000000 00000000 <7>[ 117.527296] [0: kworker/0:2: 375] mmc0: clock 0Hz busmode 2 powermode 2 cs 0 Vdd 18 width 1 timing 0 <7>[ 117.540116] [0: kworker/0:2: 375] mmc0: clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 18 width 1 timing 0 // set -EAGAIN <3>[ 117.541650] [0: kworker/0:2: 375] mmc_sd_get_cid: rocr=0xc1ff8000, retries=10. err=0 -> -11. // retry without power cycle <7>[ 117.541683] [0: kworker/0:2: 375] mmc0: clock 400000Hz busmode 2 powermode 2 cs 1 Vdd 18 width 1 timing 0 <7>[ 117.543106] [0: kworker/0:2: 375] mmc0: starting CMD0 arg 00000000 flags 000000c0 <7>[ 117.543323] I[0:id.app.reminder: 8908] mmc0: req done (CMD0): 0: 00000000 00000000 00000000 00000000 <7>[ 117.544679] [0: kworker/0:2: 375] mmc0: clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 18 width 1 timing 0 <7>[ 117.546131] [0: kworker/0:2: 375] mmc0: starting CMD8 arg 000001aa flags 000002f5 <7>[ 117.546484] I[0:id.app.reminder: 8908] mmc0: req done (CMD8): 0: 000001aa 00000000 00000000 00000000 // send ACMD41 + with SD_OCR_S18R (bit[24]) <7>[ 117.559967] [0: kworker/0:2: 375] mmc0: starting CMD55 arg 00000000 flags 000000f5 <7>[ 117.560445] I[0: ksoftirqd/0: 10] mmc0: req done (CMD55): 0: 00000120 00000000 00000000 00000000 <7>[ 117.560505] [0: kworker/0:2: 375] mmc0: starting CMD41 arg 51040000 flags 000000e1 // resp ACMD41 + without SD_ROCR_S18A (bit[24]) <7>[ 117.560853] I[0:Runtime worker : 8942] mmc0: req done (CMD41): 0: c0ff8000 00000000 00000000 00000000 <7>[ 117.562093] [0: kworker/0:2: 375] mmc0: starting CMD2 arg 00000000 flags 00000007 #3. Forced set error of CMD11 and the SD card initialized to HS mode. // send ACMD41 + with SD_OCR_S18R (bit[24]) <7>[ 115.040643] [0: kworker/0:2: 690] mmc0: starting CMD41 arg 51040000 flags 000000e1 // resp ACMD41 + with SD_ROCR_S18A (bit[24]) <7>[ 115.040990] I[0:Jit thread pool: 8904] mmc0: req done (CMD41): 0: c1ff8000 00000000 00000000 00000000 // send CMD11 and error occurs <7>[ 115.041092] [0: kworker/0:2: 690] mmc0: starting CMD11 arg 00000000 flags 00000015 <7>[ 115.041789] I[0:Jit thread pool: 8904] mmc0: req done (CMD11): -84: 00000000 00000000 00000000 00000000 // retry with power cycle (tested with this patch) <7>[ 115.041855] [0: kworker/0:2: 690] mmc0: Signal voltage switch failed, power cycling card <7>[ 115.041898] [0: kworker/0:2: 690] mmc0: clock 0Hz busmode 2 powermode 0 cs 0 Vdd 0 width 1 timing 0 <7>[ 115.045922] [0: kworker/0:2: 690] mmc0: clock 0Hz busmode 2 powermode 1 cs 0 Vdd 18 width 1 timing 0 <7>[ 115.064130] [0: kworker/0:2: 690] mmc0: clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 18 width 1 timing 0 // return error and retry after (retries = 0;) <3>[ 115.076912] [0: kworker/0:2: 690] mmc_sd_get_cid: rocr=0xc1ff8000, retries=10. err=-84. // clear SD_OCR_S18R <4>[ 115.076943] [0: kworker/0:2: 690] mmc0: Skipping voltage switch <7>[ 115.076973] [0: kworker/0:2: 690] mmc0: clock 400000Hz busmode 2 powermode 2 cs 1 Vdd 18 width 1 timing 0 <7>[ 115.078375] [0: kworker/0:2: 690] mmc0: starting CMD0 arg 00000000 flags 000000c0 <7>[ 115.078617] I[0: swapper/0: 0] mmc0: req done (CMD0): 0: 00000000 00000000 00000000 00000000 <7>[ 115.079980] [0: kworker/0:2: 690] mmc0: clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 18 width 1 timing 0 <7>[ 115.081506] [0: kworker/0:2: 690] mmc0: starting CMD8 arg 000001aa flags 000002f5 <7>[ 115.081868] I[0: swapper/0: 0] mmc0: req done (CMD8): 0: 000001aa 00000000 00000000 00000000 // send ACMD41 + without SD_OCR_S18R (bit[24]) <7>[ 115.190656] [0: kworker/0:2: 690] mmc0: starting CMD55 arg 00000000 flags 000000f5 <7>[ 115.191046] I[0:Jit thread pool: 4475] mmc0: req done (CMD55): 0: 00000120 00000000 00000000 00000000 <7>[ 115.191113] [0: kworker/0:2: 690] mmc0: starting CMD41 arg 50040000 flags 000000e1 // resp ACMD41 + without SD_ROCR_S18A (bit[24]) <7>[ 115.191474] I[0:Jit thread pool: 4475] mmc0: req done (CMD41): 0: c0ff8000 00000000 00000000 00000000 <7>[ 115.191541] [0: kworker/0:2: 690] mmc0: starting CMD2 arg 00000000 flags 00000007 #4. SD card responded with SD_ROCR_S18A from ACMD41 after power cycle, and change CMD11's error value to -EAGAIN // send ACMD41 + with SD_OCR_S18R (bit[24]) <7>[ 156.884623] [0: kworker/0:1: 7] mmc0: starting CMD41 arg 51040000 flags 000000e1 // resp ACMD41 + with SD_ROCR_S18A (bit[24]) <7>[ 156.884975] I[0: highpool[3]: 5440] mmc0: req done (CMD41): 0: c1ff8000 00000000 00000000 00000000 // send CMD11 and error occurs <7>[ 156.885051] [0: kworker/0:1: 7] mmc0: starting CMD11 arg 00000000 flags 00000015 <7>[ 156.885759] I[0: highpool[3]: 5440] mmc0: req done (CMD11): -84: 00000000 00000000 00000000 00000000 // retry with power cycle (tested with this patch) <7>[ 156.885834] [0: kworker/0:1: 7] mmc0: Signal voltage switch failed, power cycling card <7>[ 156.885875] [0: kworker/0:1: 7] mmc0: clock 0Hz busmode 2 powermode 0 cs 0 Vdd 0 width 1 timing 0 <7>[ 156.920185] [0: kworker/0:1: 7] mmc0: clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 18 width 1 timing 0 // change CMD11's error value to -EAGAIN <3>[ 156.932288] [0: kworker/0:1: 7] mmc_sd_get_cid: rocr=0xc1ff8000, retries=10. err=-84 -> -11. <7>[ 156.932336] [0: kworker/0:1: 7] mmc0: clock 400000Hz busmode 2 powermode 2 cs 1 Vdd 18 width 1 timing 0 <7>[ 156.933834] [0: kworker/0:1: 7] mmc0: starting CMD0 arg 00000000 flags 000000c0 <7>[ 156.934101] I[0:ung.android.mdx:10229] mmc0: req done (CMD0): 0: 00000000 00000000 00000000 00000000 <7>[ 156.935562] [0: kworker/0:1: 7] mmc0: clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 18 width 1 timing 0 <7>[ 156.937009] [0: kworker/0:1: 7] mmc0: starting CMD8 arg 000001aa flags 000002f5 <7>[ 156.937372] I[0:ung.android.mdx:10229] mmc0: req done (CMD8): 0: 000001aa 00000000 00000000 00000000 // send ACMD41 + with SD_OCR_S18R (bit[24]) <7>[ 157.044190] [0: kworker/0:1: 7] mmc0: starting CMD55 arg 00000000 flags 000000f5 <7>[ 157.044924] I[0:ung.android.mdx:10229] mmc0: req done (CMD55): 0: 00000120 00000000 00000000 00000000 <7>[ 157.045023] [0: kworker/0:1: 7] mmc0: starting CMD41 arg 51040000 flags 000000e1 // resp ACMD41 + with SD_ROCR_S18A (bit[24]) <7>[ 157.045389] I[0:ung.android.mdx:10229] mmc0: req done (CMD41): 0: c1ff8000 00000000 00000000 00000000 // send CMD11 and complete <7>[ 157.045467] [0: kworker/0:1: 7] mmc0: starting CMD11 arg 00000000 flags 00000015 <7>[ 157.045855] I[0: Binder:798_2: 805] mmc0: req done (CMD11): 0: 00000320 00000000 00000000 00000000 >> --- >> drivers/mmc/core/core.c | 2 +- >> 1 file changed, 1 insertion(+), 1 deletion(-) >> >> diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c index >> 1136b859ddd8..a6674df2a7bb 100644 >> --- a/drivers/mmc/core/core.c >> +++ b/drivers/mmc/core/core.c >> @@ -1207,7 +1207,7 @@ int mmc_set_uhs_voltage(struct mmc_host *host, >> u32 ocr) >> >> err = mmc_wait_for_cmd(host, &cmd, 0); >> if (err) >> - return err; >> + goto power_cycle; >> >> if (!mmc_host_is_spi(host) && (cmd.resp[0] & R1_ERROR)) >> return -EIO; >> -- >> 2.29.0 >> > >Kind regards >Uffe Thanks and regards. DooHyun Hwang. ^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2021-03-04 0:03 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <CGME20210210051209epcas1p3e55c0cbab7313731bc6e425da6189bb4@epcas1p3.samsung.com>
2021-02-10 4:59 ` [PATCH] mmc: core: add a power cycle when CMD11 fails DooHyun Hwang
2021-02-25 7:43 ` DooHyun Hwang
2021-03-02 10:38 ` Ulf Hansson
2021-03-03 6:30 ` DooHyun Hwang
2021-03-03 10:59 ` Ulf Hansson
2021-03-03 11:29 ` DooHyun Hwang
2021-03-03 6:39 ` DooHyun Hwang
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox