From: Arindam Nath <arindam.nath@amd.com>
To: cjb@laptop.org
Cc: zhangfei.gao@gmail.com, prakity@marvell.com,
subhashj@codeaurora.org, linux-mmc@vger.kernel.org,
henry.su@amd.com, aaron.lu@amd.com, anath.amd@gmail.com,
Arindam Nath <arindam.nath@amd.com>
Subject: [PATCH v2 12/12] mmc: sdhci: add support for retuning mode 1
Date: Fri, 4 Mar 2011 17:02:49 +0530 [thread overview]
Message-ID: <1299238369-1768-13-git-send-email-arindam.nath@amd.com> (raw)
In-Reply-To: <1299238369-1768-1-git-send-email-arindam.nath@amd.com>
Host Controller v3.00 can support retuning modes 1,2 or 3 depending on
the bits 46-47 of the Capabilities register. Also, the timer count for
retuning is indicated by bits 40-43 of the same register. We initialize
timer_list for retuning after successfull UHS-I initialization. Since
retuning mode 1 sets a limit of 4MB on the maximum data length, we set
max_blk_count appropriately. Once the tuning timer expires, we set
SDHCI_NEEDS_RETUNING flag, and if the flag is set, we execute tuning
procedure before sending the next command. We need to restore mmc_request
structure after executing retuning procedure since host->mrq is used
inside the procedure to send CMD19. We also disable and re-enable this
flag during suspend and resume respectively, as per the spec v3.00.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
---
drivers/mmc/core/sd.c | 5 ++
drivers/mmc/host/sdhci.c | 109 ++++++++++++++++++++++++++++++++++++++++++++-
drivers/mmc/host/sdhci.h | 6 ++-
include/linux/mmc/host.h | 1 +
include/linux/mmc/sdhci.h | 6 +++
5 files changed, 124 insertions(+), 3 deletions(-)
diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c
index ae7a771..1f3cf57 100644
--- a/drivers/mmc/core/sd.c
+++ b/drivers/mmc/core/sd.c
@@ -641,6 +641,11 @@ static int mmc_sd_init_uhs_card(struct mmc_card *card)
if (!mmc_host_is_spi(card->host) && card->host->ops->execute_tuning)
card->host->ops->execute_tuning(card->host);
+ /* Initialize and start re-tuning timer */
+ if (!mmc_host_is_spi(card->host) &&
+ card->host->ops->start_retuning_timer)
+ card->host->ops->start_retuning_timer(card->host);
+
out:
kfree(status);
diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
index 2ffb0c4..8bf0408 100644
--- a/drivers/mmc/host/sdhci.c
+++ b/drivers/mmc/host/sdhci.c
@@ -48,6 +48,8 @@ static void sdhci_finish_data(struct sdhci_host *);
static void sdhci_send_command(struct sdhci_host *, struct mmc_command *);
static void sdhci_finish_command(struct sdhci_host *);
+static void sdhci_execute_tuning(struct mmc_host *mmc);
+static void sdhci_tuning_timer(unsigned long data);
static void sdhci_dumpregs(struct sdhci_host *host)
{
@@ -1240,8 +1242,34 @@ static void sdhci_request(struct mmc_host *mmc, struct mmc_request *mrq)
if (!present || host->flags & SDHCI_DEVICE_DEAD) {
host->mrq->cmd->error = -ENOMEDIUM;
tasklet_schedule(&host->finish_tasklet);
- } else
+ } else {
+ u32 present_state;
+
+ present_state = sdhci_readl(host, SDHCI_PRESENT_STATE);
+ /*
+ * Check if the re-tuning timer has already expired and there
+ * is no on-going data transfer. If so, we need to execute
+ * tuning procedure before sending command.
+ */
+ if ((host->flags & SDHCI_NEEDS_RETUNING) &&
+ !(present_state & (SDHCI_DOING_WRITE |
+ SDHCI_DOING_READ))) {
+ host->flags &= ~SDHCI_NEEDS_RETUNING;
+ /* Reload the new initial value for timer */
+ if (host->tuning_mode == SDHCI_TUNING_MODE_1)
+ mod_timer(&host->tuning_timer, jiffies +
+ host->tuning_count * HZ);
+
+ spin_unlock_irqrestore(&host->lock, flags);
+ sdhci_execute_tuning(mmc);
+ spin_lock_irqsave(&host->lock, flags);
+
+ /* Restore original mmc_request structure */
+ host->mrq = mrq;
+ }
+
sdhci_send_command(host, mrq->cmd);
+ }
mmiowb();
spin_unlock_irqrestore(&host->lock, flags);
@@ -1667,6 +1695,26 @@ static void sdhci_disable_preset_value(struct sdhci_host *host)
sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
}
+static void sdhci_start_retuning_timer(struct mmc_host *mmc)
+{
+ struct sdhci_host *host;
+ unsigned long flags;
+
+ host = mmc_priv(mmc);
+
+ spin_lock_irqsave(&host->lock, flags);
+
+ if (host->tuning_count &&
+ (host->tuning_mode == SDHCI_TUNING_MODE_1)) {
+ mod_timer(&host->tuning_timer, jiffies + host->tuning_count *
+ HZ);
+ /* Tuning mode 1 limits the maximum data length to 4MB */
+ mmc->max_blk_count = (4 * 1024 * 1024) / mmc->max_blk_size;
+ }
+
+ spin_unlock_irqrestore(&host->lock, flags);
+}
+
static const struct mmc_host_ops sdhci_ops = {
.request = sdhci_request,
.set_ios = sdhci_set_ios,
@@ -1676,6 +1724,7 @@ static const struct mmc_host_ops sdhci_ops = {
.get_max_current_180 = sdhci_get_max_current_180,
.execute_tuning = sdhci_execute_tuning,
.enable_preset_value = sdhci_enable_preset_value,
+ .start_retuning_timer = sdhci_start_retuning_timer,
};
/*****************************************************************************\
@@ -1725,6 +1774,10 @@ static void sdhci_tasklet_finish(unsigned long param)
del_timer(&host->timer);
+ if (host->version >= SDHCI_SPEC_300)
+ del_timer(&host->tuning_timer);
+
+
mrq = host->mrq;
/*
@@ -1799,6 +1852,20 @@ static void sdhci_timeout_timer(unsigned long data)
spin_unlock_irqrestore(&host->lock, flags);
}
+static void sdhci_tuning_timer(unsigned long data)
+{
+ struct sdhci_host *host;
+ unsigned long flags;
+
+ host = (struct sdhci_host *)data;
+
+ spin_lock_irqsave(&host->lock, flags);
+
+ host->flags |= SDHCI_NEEDS_RETUNING;
+
+ spin_unlock_irqrestore(&host->lock, flags);
+}
+
/*****************************************************************************\
* *
* Interrupt handling *
@@ -2057,6 +2124,15 @@ int sdhci_suspend_host(struct sdhci_host *host, pm_message_t state)
sdhci_disable_card_detection(host);
+ /* Disable tuning since we are suspending */
+ if ((host->version >= SDHCI_SPEC_300) &&
+ host->tuning_count &&
+ (host->tuning_mode == SDHCI_TUNING_MODE_1)) {
+ host->flags &= ~SDHCI_NEEDS_RETUNING;
+ mod_timer(&host->tuning_timer, jiffies +
+ host->tuning_count * HZ);
+ }
+
ret = mmc_suspend_host(host->mmc);
if (ret)
return ret;
@@ -2098,6 +2174,12 @@ int sdhci_resume_host(struct sdhci_host *host)
ret = mmc_resume_host(host->mmc);
sdhci_enable_card_detection(host);
+ /* Set the re-tuning expiration flag */
+ if ((host->version >= SDHCI_SPEC_300) &&
+ host->tuning_count &&
+ (host->tuning_mode == SDHCI_TUNING_MODE_1))
+ host->flags |= SDHCI_NEEDS_RETUNING;
+
return ret;
}
@@ -2353,6 +2435,21 @@ int sdhci_add_host(struct sdhci_host *host)
if (caps[1] & SDHCI_DRIVER_TYPE_D)
mmc->caps |= MMC_CAP_DRIVER_TYPE_D;
+ /* Initial value for re-tuning timer count */
+ host->tuning_count = (caps[1] & SDHCI_RETUNING_TIMER_COUNT_MASK) >>
+ SDHCI_RETUNING_TIMER_COUNT_SHIFT;
+
+ /*
+ * In case Re-tuning Timer is not disabled, the actual value of
+ * re-tuning timer will be 2 ^ (n - 1).
+ */
+ if (host->tuning_count)
+ host->tuning_count = 1 << (host->tuning_count - 1);
+
+ /* Re-tuning mode supported by the Host Controller */
+ host->tuning_mode = (caps[1] & SDHCI_RETUNING_MODE_MASK) >>
+ SDHCI_RETUNING_MODE_SHIFT;
+
ocr_avail = 0;
/*
* According to SD Host Controller spec v3.00, if the Host System
@@ -2488,9 +2585,15 @@ int sdhci_add_host(struct sdhci_host *host)
setup_timer(&host->timer, sdhci_timeout_timer, (unsigned long)host);
- if (host->version >= SDHCI_SPEC_300)
+ if (host->version >= SDHCI_SPEC_300) {
init_waitqueue_head(&host->buf_ready_int);
+ /* Initialize re-tuning timer */
+ init_timer(&host->tuning_timer);
+ host->tuning_timer.data = (unsigned long)host;
+ host->tuning_timer.function = sdhci_tuning_timer;
+ }
+
ret = request_irq(host->irq, sdhci_irq, IRQF_SHARED,
mmc_hostname(mmc), host);
if (ret)
@@ -2584,6 +2687,8 @@ void sdhci_remove_host(struct sdhci_host *host, int dead)
free_irq(host->irq, host);
del_timer_sync(&host->timer);
+ if (host->version >= SDHCI_SPEC_300)
+ del_timer_sync(&host->tuning_timer);
tasklet_kill(&host->card_tasklet);
tasklet_kill(&host->finish_tasklet);
diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h
index 37a8c32..53d5909 100644
--- a/drivers/mmc/host/sdhci.h
+++ b/drivers/mmc/host/sdhci.h
@@ -190,7 +190,11 @@
#define SDHCI_DRIVER_TYPE_A 0x00000010
#define SDHCI_DRIVER_TYPE_C 0x00000020
#define SDHCI_DRIVER_TYPE_D 0x00000040
-#define SDHCI_USE_SDR50_TUNING 0x00002000
+#define SDHCI_RETUNING_TIMER_COUNT_MASK 0x00000F00
+#define SDHCI_RETUNING_TIMER_COUNT_SHIFT 8
+#define SDHCI_USE_SDR50_TUNING 0x00002000
+#define SDHCI_RETUNING_MODE_MASK 0x0000C000
+#define SDHCI_RETUNING_MODE_SHIFT 14
#define SDHCI_CLOCK_MUL_MASK 0x00FF0000
#define SDHCI_CLOCK_MUL_SHIFT 16
diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h
index e63e063..09f5d03 100644
--- a/include/linux/mmc/host.h
+++ b/include/linux/mmc/host.h
@@ -131,6 +131,7 @@ struct mmc_host_ops {
int (*get_max_current_180)(struct mmc_host *mmc);
void (*execute_tuning)(struct mmc_host *host);
void (*enable_preset_value)(struct mmc_host *host);
+ void (*start_retuning_timer)(struct mmc_host *host);
};
struct mmc_card;
diff --git a/include/linux/mmc/sdhci.h b/include/linux/mmc/sdhci.h
index 4be4022..c6539be 100644
--- a/include/linux/mmc/sdhci.h
+++ b/include/linux/mmc/sdhci.h
@@ -110,6 +110,7 @@ struct sdhci_host {
#define SDHCI_REQ_USE_DMA (1<<2) /* Use DMA for this req. */
#define SDHCI_DEVICE_DEAD (1<<3) /* Device unresponsive */
#define SDHCI_SDR50_NEEDS_TUNING (1<<4) /* SDR50 needs tuning */
+#define SDHCI_NEEDS_RETUNING (1<<5) /* Host needs retuning */
unsigned int version; /* SDHCI spec. version */
@@ -152,6 +153,11 @@ struct sdhci_host {
wait_queue_head_t buf_ready_int; /* Waitqueue for Buffer Read Ready interrupt */
unsigned int tuning_done; /* Condition flag set when CMD19 succeeds */
+ unsigned int tuning_count; /* Timer count for re-tuning */
+ unsigned int tuning_mode; /* Re-tuning mode supported by host */
+#define SDHCI_TUNING_MODE_1 0
+ struct timer_list tuning_timer; /* Timer for tuning */
+
unsigned long private[0] ____cacheline_aligned;
};
#endif /* __SDHCI_H */
--
1.7.1
next prev parent reply other threads:[~2011-03-04 11:35 UTC|newest]
Thread overview: 125+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-03-04 11:32 [PATCH v2 00/12] add support for host controller v3.00 Arindam Nath
2011-03-04 11:32 ` [PATCH v2 01/12] mmc: sdhci: add support for auto CMD23 Arindam Nath
2011-03-09 12:22 ` subhashj
2011-03-09 12:55 ` Nath, Arindam
2011-03-15 11:23 ` Subhash Jadavani
2011-03-15 11:35 ` Nath, Arindam
2011-03-15 11:52 ` Subhash Jadavani
2011-03-16 6:07 ` Nath, Arindam
2011-03-04 11:32 ` [PATCH v2 02/12] mmc: sd: add support for signal voltage switch procedure Arindam Nath
2011-03-04 11:47 ` Wolfram Sang
2011-03-04 11:52 ` Nath, Arindam
2011-03-09 10:44 ` subhashj
2011-03-10 6:30 ` subhashj
2011-03-10 8:05 ` Nath, Arindam
2011-03-09 12:45 ` zhangfei gao
2011-03-10 8:11 ` Nath, Arindam
2011-03-15 10:18 ` Subhash Jadavani
2011-03-15 10:32 ` Nath, Arindam
2011-03-15 11:18 ` Subhash Jadavani
2011-03-15 11:28 ` Nath, Arindam
2011-03-15 11:58 ` Subhash Jadavani
2011-03-16 3:03 ` zhangfei gao
2011-03-16 6:30 ` Nath, Arindam
2011-03-16 10:44 ` zhangfei gao
2011-03-16 10:48 ` Nath, Arindam
2011-03-16 21:39 ` Philip Rakity
2011-03-17 4:18 ` Nath, Arindam
2011-03-24 10:52 ` zhangfei gao
2011-03-24 10:59 ` Nath, Arindam
2011-03-04 11:32 ` [PATCH v2 03/12] mmc: sd: query function modes for uhs cards Arindam Nath
2011-03-09 14:08 ` subhashj
2011-03-09 14:31 ` Nath, Arindam
2011-03-09 18:04 ` subhashj
2011-03-09 18:16 ` Nath, Arindam
2011-03-04 11:32 ` [PATCH v2 04/12] mmc: sd: add support for driver type selection Arindam Nath
2011-03-09 5:33 ` Philip Rakity
2011-03-09 8:11 ` Nath, Arindam
2011-03-10 6:57 ` subhashj
2011-03-10 8:31 ` Nath, Arindam
2011-03-10 10:28 ` subhashj
2011-03-10 10:44 ` Nath, Arindam
2011-03-10 11:25 ` subhashj
2011-03-10 11:34 ` Nath, Arindam
2011-03-04 11:32 ` [PATCH v2 05/12] mmc: sdhci: reset sdclk before setting high speed enable Arindam Nath
2011-03-05 4:57 ` Philip Rakity
2011-03-05 5:07 ` Nath, Arindam
2011-03-04 11:32 ` [PATCH v2 06/12] mmc: sd: add support for uhs bus speed mode selection Arindam Nath
2011-03-10 8:00 ` subhashj
2011-03-10 8:36 ` Nath, Arindam
2011-03-10 10:07 ` subhashj
2011-03-10 10:15 ` Nath, Arindam
2011-03-21 6:42 ` Subhash Jadavani
2011-03-23 6:04 ` Nath, Arindam
2011-03-23 6:14 ` Subhash Jadavani
2011-03-23 6:17 ` Nath, Arindam
2011-03-23 6:26 ` Subhash Jadavani
2011-03-23 6:35 ` Nath, Arindam
2011-03-23 7:23 ` Subhash Jadavani
2011-03-23 14:02 ` Nath, Arindam
2011-03-24 7:25 ` Subhash Jadavani
2011-03-24 8:42 ` Nath, Arindam
2011-03-04 11:32 ` [PATCH v2 07/12] mmc: sd: set current limit for uhs cards Arindam Nath
2011-03-09 21:41 ` Philip Rakity
2011-03-10 3:12 ` Nath, Arindam
2011-03-10 8:16 ` subhashj
2011-03-10 8:43 ` Nath, Arindam
2011-03-10 9:45 ` subhashj
2011-03-16 14:26 ` Philip Rakity
2011-03-16 14:32 ` Nath, Arindam
2011-03-16 14:51 ` Philip Rakity
2011-03-16 15:00 ` Nath, Arindam
2011-03-16 15:18 ` Philip Rakity
2011-03-16 15:24 ` Nath, Arindam
2011-03-16 15:31 ` Philip Rakity
2011-03-16 15:33 ` Nath, Arindam
2011-03-16 15:34 ` Philip Rakity
2011-03-21 7:43 ` Subhash Jadavani
2011-03-21 7:54 ` Nath, Arindam
2011-03-04 11:32 ` [PATCH v2 08/12] mmc: sd: report correct speed and capacity of " Arindam Nath
2011-03-10 11:48 ` subhashj
2011-03-10 13:28 ` Nath, Arindam
2011-03-10 13:41 ` subhashj
2011-03-04 11:32 ` [PATCH v2 09/12] mmc: sd: add support for tuning during uhs initialization Arindam Nath
2011-03-04 18:27 ` Philip Rakity
2011-03-04 18:48 ` Nath, Arindam
2011-03-04 18:34 ` Philip Rakity
2011-03-04 18:54 ` Nath, Arindam
2011-03-15 10:32 ` zhangfei gao
2011-03-15 10:43 ` Nath, Arindam
2011-03-16 2:51 ` zhangfei gao
2011-03-16 6:20 ` Nath, Arindam
2011-03-16 10:18 ` zhangfei gao
2011-03-21 9:43 ` Subhash Jadavani
2011-03-21 9:50 ` Nath, Arindam
2011-03-23 6:58 ` Subhash Jadavani
2011-03-21 10:58 ` Subhash Jadavani
2011-03-21 11:07 ` Nath, Arindam
2011-03-23 6:08 ` Subhash Jadavani
2011-03-23 6:14 ` Nath, Arindam
2011-03-23 6:19 ` Subhash Jadavani
2011-03-23 6:22 ` Nath, Arindam
2011-03-23 6:34 ` Subhash Jadavani
2011-03-23 6:41 ` Nath, Arindam
2011-03-23 6:45 ` Subhash Jadavani
2011-03-23 6:48 ` Nath, Arindam
2011-03-04 11:32 ` [PATCH v2 10/12] mmc: sdhci: enable preset value after " Arindam Nath
2011-03-10 13:23 ` subhashj
2011-03-10 13:30 ` Nath, Arindam
2011-03-10 13:45 ` subhashj
2011-03-10 13:49 ` Nath, Arindam
2011-03-10 14:03 ` subhashj
2011-03-10 14:07 ` Nath, Arindam
2011-03-10 14:12 ` subhashj
2011-03-10 14:15 ` Nath, Arindam
2011-03-10 14:19 ` subhashj
2011-03-10 14:24 ` Nath, Arindam
2011-03-04 11:32 ` [PATCH v2 11/12] mmc: sdhci: add support for programmable clock mode Arindam Nath
2011-03-04 11:32 ` Arindam Nath [this message]
2011-03-10 13:57 ` [PATCH v2 12/12] mmc: sdhci: add support for retuning mode 1 subhashj
2011-03-10 14:00 ` Nath, Arindam
2011-03-04 15:16 ` [PATCH v2 00/12] add support for host controller v3.00 Chris Ball
2011-03-04 15:55 ` Nath, Arindam
2011-03-11 13:13 ` subhashj
2011-03-11 15:29 ` Nath, Arindam
2011-03-11 16:06 ` Chris Ball
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1299238369-1768-13-git-send-email-arindam.nath@amd.com \
--to=arindam.nath@amd.com \
--cc=aaron.lu@amd.com \
--cc=anath.amd@gmail.com \
--cc=cjb@laptop.org \
--cc=henry.su@amd.com \
--cc=linux-mmc@vger.kernel.org \
--cc=prakity@marvell.com \
--cc=subhashj@codeaurora.org \
--cc=zhangfei.gao@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).