From: Subhash Jadavani <subhashj@codeaurora.org>
To: linux-mmc@vger.kernel.org
Cc: linux-arm-msm@vger.kernel.org,
Subhash Jadavani <subhashj@codeaurora.org>
Subject: [PATCH] mmc: sd: UHS-I bus speed should be set last in UHS initialization
Date: Mon, 1 Aug 2011 17:28:17 +0530 [thread overview]
Message-ID: <1312199897-5536-1-git-send-email-subhashj@codeaurora.org> (raw)
mmc_sd_init_uhs_card function sets the driver type, current limit
and bus speed mode on card as well as on host controller side.
Currently bus speed mode is set by sending CMD6 to card and
immediately setting the timing mode in host controller. But
then before initiating tuning sequence, it also tries to set
current limit by sending CMD6 to card which results in data
timeout errors in controller if bus speed mode is SDR50/SDR104 mode.
So basically bus speed mode should be set only after current limit
is set in the card and immediately after setting the bus speed mode,
tuning sequence should be initiated.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
---
drivers/mmc/core/sd.c | 57 ++++++++++++++++++++++++++++++++----------------
1 files changed, 38 insertions(+), 19 deletions(-)
diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c
index ff27741..d257496 100644
--- a/drivers/mmc/core/sd.c
+++ b/drivers/mmc/core/sd.c
@@ -459,10 +459,9 @@ static int sd_select_driver_type(struct mmc_card *card, u8 *status)
return 0;
}
-static int sd_set_bus_speed_mode(struct mmc_card *card, u8 *status)
+static int sd_get_bus_speed_mode(struct mmc_card *card)
{
- unsigned int bus_speed = 0, timing = 0;
- int err;
+ int bus_speed = 0;
/*
* If the host doesn't support any of the UHS-I modes, fallback on
@@ -470,37 +469,56 @@ static int sd_set_bus_speed_mode(struct mmc_card *card, u8 *status)
*/
if (!(card->host->caps & (MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25 |
MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR104 | MMC_CAP_UHS_DDR50)))
- return 0;
+ return -EINVAL;
if ((card->host->caps & MMC_CAP_UHS_SDR104) &&
(card->sw_caps.sd3_bus_mode & SD_MODE_UHS_SDR104)) {
bus_speed = UHS_SDR104_BUS_SPEED;
- timing = MMC_TIMING_UHS_SDR104;
- card->sw_caps.uhs_max_dtr = UHS_SDR104_MAX_DTR;
} else if ((card->host->caps & MMC_CAP_UHS_DDR50) &&
(card->sw_caps.sd3_bus_mode & SD_MODE_UHS_DDR50)) {
bus_speed = UHS_DDR50_BUS_SPEED;
- timing = MMC_TIMING_UHS_DDR50;
- card->sw_caps.uhs_max_dtr = UHS_DDR50_MAX_DTR;
} else if ((card->host->caps & (MMC_CAP_UHS_SDR104 |
MMC_CAP_UHS_SDR50)) && (card->sw_caps.sd3_bus_mode &
SD_MODE_UHS_SDR50)) {
bus_speed = UHS_SDR50_BUS_SPEED;
- timing = MMC_TIMING_UHS_SDR50;
- card->sw_caps.uhs_max_dtr = UHS_SDR50_MAX_DTR;
} else if ((card->host->caps & (MMC_CAP_UHS_SDR104 |
MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR25)) &&
(card->sw_caps.sd3_bus_mode & SD_MODE_UHS_SDR25)) {
bus_speed = UHS_SDR25_BUS_SPEED;
- timing = MMC_TIMING_UHS_SDR25;
- card->sw_caps.uhs_max_dtr = UHS_SDR25_MAX_DTR;
} else if ((card->host->caps & (MMC_CAP_UHS_SDR104 |
MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR25 |
MMC_CAP_UHS_SDR12)) && (card->sw_caps.sd3_bus_mode &
SD_MODE_UHS_SDR12)) {
bus_speed = UHS_SDR12_BUS_SPEED;
+ }
+
+ return bus_speed;
+}
+
+static int sd_set_bus_speed_mode(struct mmc_card *card, u8 *status)
+{
+ int err, bus_speed;
+ unsigned int timing = 0;
+
+ bus_speed = sd_get_bus_speed_mode(card);
+
+ if (bus_speed == UHS_SDR104_BUS_SPEED) {
+ timing = MMC_TIMING_UHS_SDR104;
+ card->sw_caps.uhs_max_dtr = UHS_SDR104_MAX_DTR;
+ } else if (bus_speed == UHS_DDR50_BUS_SPEED) {
+ timing = MMC_TIMING_UHS_DDR50;
+ card->sw_caps.uhs_max_dtr = UHS_DDR50_MAX_DTR;
+ } else if (bus_speed == UHS_SDR50_BUS_SPEED) {
+ timing = MMC_TIMING_UHS_SDR50;
+ card->sw_caps.uhs_max_dtr = UHS_SDR50_MAX_DTR;
+ } else if (bus_speed == UHS_SDR25_BUS_SPEED) {
+ timing = MMC_TIMING_UHS_SDR25;
+ card->sw_caps.uhs_max_dtr = UHS_SDR25_MAX_DTR;
+ } else if (bus_speed == UHS_SDR12_BUS_SPEED) {
timing = MMC_TIMING_UHS_SDR12;
card->sw_caps.uhs_max_dtr = UHS_SDR12_MAX_DTR;
+ } else {
+ return -EINVAL;
}
card->sd_bus_speed = bus_speed;
@@ -522,6 +540,7 @@ static int sd_set_bus_speed_mode(struct mmc_card *card, u8 *status)
static int sd_set_current_limit(struct mmc_card *card, u8 *status)
{
int current_limit = 0;
+ unsigned int bus_speed = sd_get_bus_speed_mode(card);
int err;
/*
@@ -529,9 +548,9 @@ static int sd_set_current_limit(struct mmc_card *card, u8 *status)
* bus speed modes. For other bus speed modes, we set the default
* current limit of 200mA.
*/
- if ((card->sd_bus_speed == UHS_SDR50_BUS_SPEED) ||
- (card->sd_bus_speed == UHS_SDR104_BUS_SPEED) ||
- (card->sd_bus_speed == UHS_DDR50_BUS_SPEED)) {
+ if ((bus_speed == UHS_SDR50_BUS_SPEED) ||
+ (bus_speed == UHS_SDR104_BUS_SPEED) ||
+ (bus_speed == UHS_DDR50_BUS_SPEED)) {
if (card->host->caps & MMC_CAP_MAX_CURRENT_800) {
if (card->sw_caps.sd3_curr_limit & SD_MAX_CURRENT_800)
current_limit = SD_SET_CURRENT_LIMIT_800;
@@ -613,13 +632,13 @@ static int mmc_sd_init_uhs_card(struct mmc_card *card)
if (err)
goto out;
- /* Set bus speed mode of the card */
- err = sd_set_bus_speed_mode(card, status);
+ /* Set current limit for the card */
+ err = sd_set_current_limit(card, status);
if (err)
goto out;
- /* Set current limit for the card */
- err = sd_set_current_limit(card, status);
+ /* Set bus speed mode of the card */
+ err = sd_set_bus_speed_mode(card, status);
if (err)
goto out;
--
1.7.1.1
--
Sent by a consultant of the Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum.
next reply other threads:[~2011-08-01 11:58 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-08-01 11:58 Subhash Jadavani [this message]
2011-08-01 20:09 ` [PATCH] mmc: sd: UHS-I bus speed should be set last in UHS initialization Chris Ball
2011-08-02 7:08 ` Nath, Arindam
2011-08-02 9:12 ` Subhash Jadavani
2011-08-02 9:51 ` Nath, Arindam
2011-08-02 12:40 ` Subhash Jadavani
2011-08-05 13:30 ` Issue with non-UHS-I SD3.0 cards Subhash Jadavani
2011-08-05 18:44 ` Nath, Arindam
2011-08-05 18:57 ` Nath, Arindam
2011-08-08 6:20 ` Subhash Jadavani
2011-08-08 6:42 ` Nath, Arindam
2011-08-05 19:08 ` Nath, Arindam
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1312199897-5536-1-git-send-email-subhashj@codeaurora.org \
--to=subhashj@codeaurora.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox