From: Lucas Stach <l.stach@pengutronix.de>
To: linux-mmc@vger.kernel.org
Cc: Shawn Guo <shawn.guo@linaro.org>, Chris Ball <cjb@laptop.org>,
Lucas Stach <l.stach@pengutronix.de>
Subject: [PATCH] mmc: sdhci-esdhc-imx: fix multiblock reads on i.MX53
Date: Thu, 14 Mar 2013 15:43:45 +0100 [thread overview]
Message-ID: <1363272225-1304-1-git-send-email-l.stach@pengutronix.de> (raw)
The eSDHC controller on the i.MX53 needs an additional, non spec
compliant CMD12 after a multiblock read with a predefined number of
blocks. Otherwise the internal state machine won't go back to the
idle state.
This commit effectively reverts ebe31e44 (mmc: sdhci-esdhc-imx:
fix for mmc cards on i.MX5), which fixed part of the problem by
making multiblock reads work, however this fix was not sufficient
when multi- and singleblock reads got intermixed.
This implements the recommended workaround by manually sending a
CMD12 with the RSPTYP bits cleared.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
---
drivers/mmc/host/sdhci-esdhc-imx.c | 38 +++++++++++++++++++++++++++++++++---
1 file changed, 35 insertions(+), 3 deletions(-)
diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
index 78ac002..bd3830d 100644
--- a/drivers/mmc/host/sdhci-esdhc-imx.c
+++ b/drivers/mmc/host/sdhci-esdhc-imx.c
@@ -85,6 +85,14 @@ struct pltfm_imx_data {
struct clk *clk_ipg;
struct clk *clk_ahb;
struct clk *clk_per;
+ /*
+ * controller multiblock status:
+ * 0: no multiblock command pending
+ * 1: exact multiblock command in process
+ * 2: multiblock command finished by CMD12, waiting for response INT
+ */
+ unsigned char multiblock_status;
+
};
static struct platform_device_id imx_esdhc_devtype[] = {
@@ -154,6 +162,8 @@ static inline void esdhc_clrset_le(struct sdhci_host *host, u32 mask, u32 val, i
static u32 esdhc_readl_le(struct sdhci_host *host, int reg)
{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct pltfm_imx_data *imx_data = pltfm_host->priv;
u32 val = readl(host->ioaddr + reg);
if (unlikely(reg == SDHCI_CAPABILITIES)) {
@@ -175,6 +185,18 @@ static u32 esdhc_readl_le(struct sdhci_host *host, int reg)
val &= ~ESDHC_INT_VENDOR_SPEC_DMA_ERR;
val |= SDHCI_INT_ADMA_ERROR;
}
+
+ /*
+ * mask off the interrupt we get in response to the manually
+ * sent CMD12
+ */
+ if ((imx_data->multiblock_status == 2) &&
+ ((val & SDHCI_INT_RESPONSE) == SDHCI_INT_RESPONSE)) {
+ val &= ~SDHCI_INT_RESPONSE;
+ writel(SDHCI_INT_RESPONSE, host->ioaddr +
+ SDHCI_INT_STATUS);
+ imx_data->multiblock_status = 0;
+ }
}
return val;
@@ -211,6 +233,14 @@ static void esdhc_writel_le(struct sdhci_host *host, u32 val, int reg)
v = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
v &= ~ESDHC_VENDOR_SPEC_SDIO_QUIRK;
writel(v, host->ioaddr + ESDHC_VENDOR_SPEC);
+
+ if (imx_data->multiblock_status == 1) {
+ /* send a manual CMD12 with RESPTYP=none */
+ data = MMC_STOP_TRANSMISSION << 24 |
+ SDHCI_CMD_ABORTCMD << 16;
+ writel(data, host->ioaddr + SDHCI_TRANSFER_MODE);
+ imx_data->multiblock_status = 2;
+ }
}
if (unlikely(reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE)) {
@@ -277,11 +307,13 @@ static void esdhc_writew_le(struct sdhci_host *host, u16 val, int reg)
}
return;
case SDHCI_COMMAND:
- if ((host->cmd->opcode == MMC_STOP_TRANSMISSION ||
- host->cmd->opcode == MMC_SET_BLOCK_COUNT) &&
- (imx_data->flags & ESDHC_FLAG_MULTIBLK_NO_INT))
+ if (host->cmd->opcode == MMC_STOP_TRANSMISSION)
val |= SDHCI_CMD_ABORTCMD;
+ if ((host->cmd->opcode == MMC_SET_BLOCK_COUNT) &&
+ (imx_data->flags & ESDHC_FLAG_MULTIBLK_NO_INT))
+ imx_data->multiblock_status = 1;
+
if (is_imx6q_usdhc(imx_data))
writel(val << 16,
host->ioaddr + SDHCI_TRANSFER_MODE);
--
1.7.10.4
next reply other threads:[~2013-03-14 14:44 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-03-14 14:43 Lucas Stach [this message]
2013-03-15 7:25 ` [PATCH] mmc: sdhci-esdhc-imx: fix multiblock reads on i.MX53 Shawn Guo
2013-03-15 8:49 ` [PATCH v2] " Lucas Stach
2013-04-16 6:45 ` Lucas Stach
2013-05-26 17:14 ` Chris Ball
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1363272225-1304-1-git-send-email-l.stach@pengutronix.de \
--to=l.stach@pengutronix.de \
--cc=cjb@laptop.org \
--cc=linux-mmc@vger.kernel.org \
--cc=shawn.guo@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).