From: Axel Lin <axel.lin@ingics.com>
To: Chris Ball <cjb@laptop.org>
Cc: Tony Prisk <linux@prisktech.co.nz>, linux-mmc@vger.kernel.org
Subject: [PATCH RFT] mmc: wmt-sdmmc: Fix setting BM_EIGHTBIT_MODE bit in wmt_mci_set_ios()
Date: Tue, 22 Oct 2013 16:54:22 +0800 [thread overview]
Message-ID: <1382432062.4804.1.camel@phoenix> (raw)
For MMC_BUS_WIDTH_8 case, current code missed setting BM_EIGHTBIT_MODE bit.
Also has a small refactor to make the code looks better in readability.
So the bit settings witch below logic:
SDMMC_BUSMODE register:
Set EIGHTBIT_MODE bit for 8 bit mode, Set FOURBIT_MODE bit for 4 bit mode.
Clear both EIGHTBIT_MODE and FOURBIT_MODE bits for 1 bit mode.
SDMMC_EXTCTRL register:
Set EXT_EIGHTBIT bit for 8 bit mode, Clear EXT_EIGHTBIT bit for 1/4 bit mode.
Add define for EXT_EIGHTBIT to avoid using magic number.
BM_ONEBIT_MASK is no longer used, thus remove it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
---
Hi Tony,
After checking wm8505+sdmmc+controller+suppliment.pdf, I'm wondering if this
dirver works for MMC_BUS_WIDTH_8 case without setting BM_EIGHTBIT_MODE bit.
I don't have this h/w to test.
I'd appreciate if you can review and test if this patch works.
Thanks,
Axel
drivers/mmc/host/wmt-sdmmc.c | 31 +++++++++++++++----------------
1 file changed, 15 insertions(+), 16 deletions(-)
diff --git a/drivers/mmc/host/wmt-sdmmc.c b/drivers/mmc/host/wmt-sdmmc.c
index 8a48a50..6ed18f8 100644
--- a/drivers/mmc/host/wmt-sdmmc.c
+++ b/drivers/mmc/host/wmt-sdmmc.c
@@ -72,7 +72,6 @@
#define BM_SPI_CS 0x20
#define BM_SD_POWER 0x40
#define BM_SOFT_RESET 0x80
-#define BM_ONEBIT_MASK 0xFD
/* SDMMC_BLKLEN bit fields */
#define BLKL_CRCERR_ABORT 0x0800
@@ -120,6 +119,8 @@
#define STS2_DATARSP_BUSY 0x20
#define STS2_DIS_FORCECLK 0x80
+/* SDMMC_EXTCTRL bit fields */
+#define EXT_EIGHTBIT 0x04
/* MMC/SD DMA Controller Registers */
#define SDDMA_GCR 0x100
@@ -672,7 +673,7 @@ static void wmt_mci_request(struct mmc_host *mmc, struct mmc_request *req)
static void wmt_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
{
struct wmt_mci_priv *priv;
- u32 reg_tmp;
+ u32 busmode, extctrl;
priv = mmc_priv(mmc);
@@ -687,28 +688,26 @@ static void wmt_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
if (ios->clock != 0)
clk_set_rate(priv->clk_sdmmc, ios->clock);
+ busmode = readb(priv->sdmmc_base + SDMMC_BUSMODE);
+ extctrl = readb(priv->sdmmc_base + SDMMC_EXTCTRL);
+
+ busmode &= ~(BM_EIGHTBIT_MODE | BM_FOURBIT_MODE);
+ extctrl &= ~EXT_EIGHTBIT;
+
switch (ios->bus_width) {
case MMC_BUS_WIDTH_8:
- reg_tmp = readb(priv->sdmmc_base + SDMMC_EXTCTRL);
- writeb(reg_tmp | 0x04, priv->sdmmc_base + SDMMC_EXTCTRL);
+ busmode |= BM_EIGHTBIT_MODE;
+ extctrl |= EXT_EIGHTBIT;
break;
case MMC_BUS_WIDTH_4:
- reg_tmp = readb(priv->sdmmc_base + SDMMC_BUSMODE);
- writeb(reg_tmp | BM_FOURBIT_MODE, priv->sdmmc_base +
- SDMMC_BUSMODE);
-
- reg_tmp = readb(priv->sdmmc_base + SDMMC_EXTCTRL);
- writeb(reg_tmp & 0xFB, priv->sdmmc_base + SDMMC_EXTCTRL);
+ busmode |= BM_FOURBIT_MODE;
break;
case MMC_BUS_WIDTH_1:
- reg_tmp = readb(priv->sdmmc_base + SDMMC_BUSMODE);
- writeb(reg_tmp & BM_ONEBIT_MASK, priv->sdmmc_base +
- SDMMC_BUSMODE);
-
- reg_tmp = readb(priv->sdmmc_base + SDMMC_EXTCTRL);
- writeb(reg_tmp & 0xFB, priv->sdmmc_base + SDMMC_EXTCTRL);
break;
}
+
+ writeb(busmode, priv->sdmmc_base + SDMMC_BUSMODE);
+ writeb(extctrl, priv->sdmmc_base + SDMMC_EXTCTRL);
}
static int wmt_mci_get_ro(struct mmc_host *mmc)
--
1.8.1.2
next reply other threads:[~2013-10-22 8:54 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-10-22 8:54 Axel Lin [this message]
2013-10-23 4:51 ` [PATCH RFT] mmc: wmt-sdmmc: Fix setting BM_EIGHTBIT_MODE bit in wmt_mci_set_ios() Tony Prisk
2013-10-23 6:48 ` Axel Lin
2013-10-23 18:10 ` Tony Prisk
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1382432062.4804.1.camel@phoenix \
--to=axel.lin@ingics.com \
--cc=cjb@laptop.org \
--cc=linux-mmc@vger.kernel.org \
--cc=linux@prisktech.co.nz \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox