* [PATCH v3 1/5] mmc: dt-bindings: add ZTE ZX296718 MMC bindings
2016-11-03 13:31 [PATCH v3 0/5] Add intial support to DW MMC host on ZTE SoC Jun Nie
@ 2016-11-03 13:31 ` Jun Nie
2016-11-04 10:24 ` Jaehoon Chung
2016-11-03 13:31 ` [PATCH v3 2/5] mmc: zx: Initial support for ZX mmc controller Jun Nie
` (3 subsequent siblings)
4 siblings, 1 reply; 7+ messages in thread
From: Jun Nie @ 2016-11-03 13:31 UTC (permalink / raw)
To: shawn.guo, xie.baoyou
Cc: ulf.hansson, jh80.chung, jason.liu, linux-mmc, Jun Nie
Document the device-tree binding of ZTE MMC host on
ZX296718 SoC.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
---
.../devicetree/bindings/mmc/zx-dw-mshc.txt | 34 ++++++++++++++++++++++
1 file changed, 34 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt
diff --git a/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt
new file mode 100644
index 0000000..5e1e16d
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt
@@ -0,0 +1,34 @@
+* ZTE specific extensions to the Synopsys Designware Mobile Storage
+ Host Controller
+
+The Synopsys designware mobile storage host controller is used to interface
+a SoC with storage medium such as eMMC or SD/MMC cards. This file documents
+differences between the core Synopsys dw mshc controller properties described
+by synopsys-dw-mshc.txt and the properties used by the ZTE specific
+extensions to the Synopsys Designware Mobile Storage Host Controller.
+
+Required Properties:
+
+* compatible: should be
+ - "zte,zx296718-dw-mshc": for ZX SoCs
+
+Example:
+
+ mmc1: mmc@1110000 {
+ compatible = "zte,zx296718-dw-mshc";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x01110000 0x1000>;
+ interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+ fifo-depth = <32>;
+ data-addr = <0x200>;
+ fifo-watermark-aligned;
+ bus-width = <4>;
+ clock-frequency = <50000000>;
+ clocks = <&topcrm SD0_AHB>, <&topcrm SD0_WCLK>;
+ clock-names = "biu", "ciu";
+ num-slots = <1>;
+ max-frequency = <50000000>;
+ cap-sdio-irq;
+ cap-sd-highspeed;
+ status = "disabled";
--
1.9.1
^ permalink raw reply related [flat|nested] 7+ messages in thread* Re: [PATCH v3 1/5] mmc: dt-bindings: add ZTE ZX296718 MMC bindings
2016-11-03 13:31 ` [PATCH v3 1/5] mmc: dt-bindings: add ZTE ZX296718 MMC bindings Jun Nie
@ 2016-11-04 10:24 ` Jaehoon Chung
0 siblings, 0 replies; 7+ messages in thread
From: Jaehoon Chung @ 2016-11-04 10:24 UTC (permalink / raw)
To: Jun Nie, shawn.guo, xie.baoyou; +Cc: ulf.hansson, jason.liu, linux-mmc
On 11/03/2016 10:31 PM, Jun Nie wrote:
> Document the device-tree binding of ZTE MMC host on
> ZX296718 SoC.
>
> Signed-off-by: Jun Nie <jun.nie@linaro.org>
> ---
> .../devicetree/bindings/mmc/zx-dw-mshc.txt | 34 ++++++++++++++++++++++
> 1 file changed, 34 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt
>
> diff --git a/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt
> new file mode 100644
> index 0000000..5e1e16d
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt
> @@ -0,0 +1,34 @@
> +* ZTE specific extensions to the Synopsys Designware Mobile Storage
> + Host Controller
> +
> +The Synopsys designware mobile storage host controller is used to interface
> +a SoC with storage medium such as eMMC or SD/MMC cards. This file documents
> +differences between the core Synopsys dw mshc controller properties described
> +by synopsys-dw-mshc.txt and the properties used by the ZTE specific
> +extensions to the Synopsys Designware Mobile Storage Host Controller.
> +
> +Required Properties:
> +
> +* compatible: should be
> + - "zte,zx296718-dw-mshc": for ZX SoCs
> +
> +Example:
> +
> + mmc1: mmc@1110000 {
> + compatible = "zte,zx296718-dw-mshc";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x01110000 0x1000>;
> + interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
> + fifo-depth = <32>;
> + data-addr = <0x200>;
> + fifo-watermark-aligned;
> + bus-width = <4>;
> + clock-frequency = <50000000>;
> + clocks = <&topcrm SD0_AHB>, <&topcrm SD0_WCLK>;
> + clock-names = "biu", "ciu";
> + num-slots = <1>;
> + max-frequency = <50000000>;
> + cap-sdio-irq;
> + cap-sd-highspeed;
> + status = "disabled";
bracket is not pair?
Other things look good to me.
Best Regards,
Jaehoon Chung
>
^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH v3 2/5] mmc: zx: Initial support for ZX mmc controller
2016-11-03 13:31 [PATCH v3 0/5] Add intial support to DW MMC host on ZTE SoC Jun Nie
2016-11-03 13:31 ` [PATCH v3 1/5] mmc: dt-bindings: add ZTE ZX296718 MMC bindings Jun Nie
@ 2016-11-03 13:31 ` Jun Nie
2016-11-03 13:31 ` [PATCH v3 3/5] Documentation: synopsys-dw-mshc: add binding for fifo quirks Jun Nie
` (2 subsequent siblings)
4 siblings, 0 replies; 7+ messages in thread
From: Jun Nie @ 2016-11-03 13:31 UTC (permalink / raw)
To: shawn.guo, xie.baoyou
Cc: ulf.hansson, jh80.chung, jason.liu, linux-mmc, Jun Nie
This platform driver adds initial support for the DW host controller
found on ZTE SoCs.
It has been tested on ZX296718 EVB board currently. More support on
timing tuning will be added when hardware is available.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
---
drivers/mmc/host/Kconfig | 9 ++
drivers/mmc/host/Makefile | 1 +
drivers/mmc/host/dw_mmc-zx.c | 242 +++++++++++++++++++++++++++++++++++++++++++
drivers/mmc/host/dw_mmc-zx.h | 31 ++++++
4 files changed, 283 insertions(+)
create mode 100644 drivers/mmc/host/dw_mmc-zx.c
create mode 100644 drivers/mmc/host/dw_mmc-zx.h
diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
index 5274f50..4dafbc2 100644
--- a/drivers/mmc/host/Kconfig
+++ b/drivers/mmc/host/Kconfig
@@ -662,6 +662,15 @@ config MMC_DW_ROCKCHIP
Synopsys DesignWare Memory Card Interface driver. Select this option
for platforms based on RK3066, RK3188 and RK3288 SoC's.
+config MMC_DW_ZX
+ tristate "ZTE specific extensions for Synopsys DW Memory Card Interface"
+ depends on MMC_DW && ARCH_ZX
+ select MMC_DW_PLTFM
+ help
+ This selects support for ZTE SoC specific extensions to the
+ Synopsys DesignWare Memory Card Interface driver. Select this option
+ for platforms based on ZX296718 SoC's.
+
config MMC_SH_MMCIF
tristate "SuperH Internal MMCIF support"
depends on HAS_DMA
diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
index e2bdaaf..9766143 100644
--- a/drivers/mmc/host/Makefile
+++ b/drivers/mmc/host/Makefile
@@ -48,6 +48,7 @@ obj-$(CONFIG_MMC_DW_EXYNOS) += dw_mmc-exynos.o
obj-$(CONFIG_MMC_DW_K3) += dw_mmc-k3.o
obj-$(CONFIG_MMC_DW_PCI) += dw_mmc-pci.o
obj-$(CONFIG_MMC_DW_ROCKCHIP) += dw_mmc-rockchip.o
+obj-$(CONFIG_MMC_DW_ZX) += dw_mmc-zx.o
obj-$(CONFIG_MMC_SH_MMCIF) += sh_mmcif.o
obj-$(CONFIG_MMC_JZ4740) += jz4740_mmc.o
obj-$(CONFIG_MMC_VUB300) += vub300.o
diff --git a/drivers/mmc/host/dw_mmc-zx.c b/drivers/mmc/host/dw_mmc-zx.c
new file mode 100644
index 0000000..de77408
--- /dev/null
+++ b/drivers/mmc/host/dw_mmc-zx.c
@@ -0,0 +1,242 @@
+/*
+ * ZX Specific Extensions for Synopsys DW Multimedia Card Interface driver
+ *
+ * Copyright (C) 2016, Linaro Ltd.
+ * Copyright (C) 2016, ZTE Corp.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/clk.h>
+#include <linux/mfd/syscon.h>
+#include <linux/mmc/dw_mmc.h>
+#include <linux/mmc/host.h>
+#include <linux/mmc/mmc.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+
+#include "dw_mmc.h"
+#include "dw_mmc-pltfm.h"
+#include "dw_mmc-zx.h"
+
+struct dw_mci_zx_priv_data {
+ struct regmap *sysc_base;
+};
+
+enum delay_type {
+ DELAY_TYPE_READ, /* read dqs delay */
+ DELAY_TYPE_CLK, /* clk sample delay */
+};
+
+static int dw_mci_zx_emmc_set_delay(struct dw_mci *host, unsigned int delay,
+ enum delay_type dflag)
+{
+ struct dw_mci_zx_priv_data *priv = host->priv;
+ struct regmap *sysc_base = priv->sysc_base;
+ unsigned int clksel;
+ unsigned int loop = 1000;
+ int ret;
+
+ if (!sysc_base)
+ return -EINVAL;
+
+ ret = regmap_update_bits(sysc_base, LB_AON_EMMC_CFG_REG0,
+ PARA_HALF_CLK_MODE | PARA_DLL_BYPASS_MODE |
+ PARA_PHASE_DET_SEL_MASK |
+ PARA_DLL_LOCK_NUM_MASK |
+ DLL_REG_SET | PARA_DLL_START_MASK,
+ PARA_DLL_START(4) | PARA_DLL_LOCK_NUM(4));
+ if (ret)
+ return ret;
+
+ ret = regmap_read(sysc_base, LB_AON_EMMC_CFG_REG1, &clksel);
+ if (ret)
+ return ret;
+
+ if (dflag == DELAY_TYPE_CLK) {
+ clksel &= ~CLK_SAMP_DELAY_MASK;
+ clksel |= CLK_SAMP_DELAY(delay);
+ } else {
+ clksel &= ~READ_DQS_DELAY_MASK;
+ clksel |= READ_DQS_DELAY(delay);
+ }
+
+ regmap_write(sysc_base, LB_AON_EMMC_CFG_REG1, clksel);
+ regmap_update_bits(sysc_base, LB_AON_EMMC_CFG_REG0,
+ PARA_DLL_START_MASK | PARA_DLL_LOCK_NUM_MASK |
+ DLL_REG_SET,
+ PARA_DLL_START(4) | PARA_DLL_LOCK_NUM(4) |
+ DLL_REG_SET);
+
+ do {
+ ret = regmap_read(sysc_base, LB_AON_EMMC_CFG_REG2, &clksel);
+ if (ret)
+ return ret;
+
+ } while (--loop && !(clksel & ZX_DLL_LOCKED));
+
+ if (!loop) {
+ dev_err(host->dev, "Error: %s dll lock fail\n", __func__);
+ return -EIO;
+ }
+
+ return 0;
+}
+
+static int dw_mci_zx_emmc_execute_tuning(struct dw_mci_slot *slot, u32 opcode)
+{
+ struct dw_mci *host = slot->host;
+ struct mmc_host *mmc = slot->mmc;
+ int len, start = 0, end = 0, delay, best = 0;
+
+ for (delay = 1 ; delay < 128; delay++) {
+ dw_mci_zx_emmc_set_delay(host, delay, DELAY_TYPE_CLK);
+ if (mmc_send_tuning(mmc, opcode, NULL)) {
+ if (start >= 0) {
+ end = delay - 1;
+ /* check and update longest good range */
+ if ((end - start) > len) {
+ best = (start + end) >> 1;
+ len = end - start;
+ }
+ }
+ start = -1;
+ end = 0;
+ continue;
+ }
+ if (start < 0)
+ start = delay;
+ }
+
+ if (start >= 0) {
+ end = delay - 1;
+ if ((end - start) > len) {
+ best = (start + end) >> 1;
+ len = end - start;
+ }
+ }
+ if (best < 0)
+ return -EIO;
+
+ dev_info(host->dev, "%s best range: start %d end %d\n", __func__,
+ start, end);
+ dw_mci_zx_emmc_set_delay(host, best, DELAY_TYPE_CLK);
+ return 0;
+}
+
+static int dw_mci_zx_prepare_hs400_tuning(struct dw_mci *host,
+ struct mmc_ios *ios)
+{
+ int ret;
+
+ /* config phase shift as 90 degree */
+ ret = dw_mci_zx_emmc_set_delay(host, 32, DELAY_TYPE_READ);
+ if (ret < 0)
+ return -EIO;
+
+ return 0;
+}
+
+static int dw_mci_zx_execute_tuning(struct dw_mci_slot *slot, u32 opcode)
+{
+ struct dw_mci *host = slot->host;
+
+ if (host->verid == 0x290a) /* only for emmc */
+ return dw_mci_zx_emmc_execute_tuning(slot, opcode);
+ /* TODO: Add 0x210a dedicated tuning for sd/sdio */
+
+ return 0;
+}
+
+static int dw_mci_zx_parse_dt(struct dw_mci *host)
+{
+ struct device_node *np = host->dev->of_node;
+ struct device_node *node;
+ struct dw_mci_zx_priv_data *priv;
+ struct regmap *sysc_base;
+ int ret;
+
+ /* syscon is needed only by emmc */
+ node = of_parse_phandle(np, "zte,aon-syscon", 0);
+ if (node) {
+ sysc_base = syscon_node_to_regmap(node);
+ of_node_put(node);
+
+ if (IS_ERR(sysc_base)) {
+ ret = PTR_ERR(sysc_base);
+ if (ret != -EPROBE_DEFER)
+ dev_err(host->dev, "Can't get syscon: %d\n",
+ ret);
+ return ret;
+ }
+ } else {
+ return 0;
+ }
+
+ priv = devm_kzalloc(host->dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+ priv->sysc_base = sysc_base;
+ host->priv = priv;
+
+ return 0;
+}
+
+static unsigned long zx_dwmmc_caps[3] = {
+ MMC_CAP_CMD23,
+ MMC_CAP_CMD23,
+ MMC_CAP_CMD23,
+};
+
+static const struct dw_mci_drv_data zx_drv_data = {
+ .caps = zx_dwmmc_caps,
+ .execute_tuning = dw_mci_zx_execute_tuning,
+ .prepare_hs400_tuning = dw_mci_zx_prepare_hs400_tuning,
+ .parse_dt = dw_mci_zx_parse_dt,
+};
+
+static const struct of_device_id dw_mci_zx_match[] = {
+ { .compatible = "zte,zx296718-dw-mshc", .data = &zx_drv_data},
+};
+MODULE_DEVICE_TABLE(of, dw_mci_zx_match);
+
+static int dw_mci_zx_probe(struct platform_device *pdev)
+{
+ const struct dw_mci_drv_data *drv_data;
+ const struct of_device_id *match;
+
+ match = of_match_node(dw_mci_zx_match, pdev->dev.of_node);
+ drv_data = match->data;
+
+ return dw_mci_pltfm_register(pdev, drv_data);
+}
+
+static const struct dev_pm_ops dw_mci_zx_dev_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
+ pm_runtime_force_resume)
+ SET_RUNTIME_PM_OPS(dw_mci_runtime_suspend,
+ dw_mci_runtime_resume,
+ NULL)
+};
+
+static struct platform_driver dw_mci_zx_pltfm_driver = {
+ .probe = dw_mci_zx_probe,
+ .remove = dw_mci_pltfm_remove,
+ .driver = {
+ .name = "dwmmc_zx",
+ .of_match_table = dw_mci_zx_match,
+ .pm = &dw_mci_zx_dev_pm_ops,
+ },
+};
+
+module_platform_driver(dw_mci_zx_pltfm_driver);
+
+MODULE_DESCRIPTION("ZTE emmc/sd driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/mmc/host/dw_mmc-zx.h b/drivers/mmc/host/dw_mmc-zx.h
new file mode 100644
index 0000000..f369997
--- /dev/null
+++ b/drivers/mmc/host/dw_mmc-zx.h
@@ -0,0 +1,31 @@
+#ifndef _DW_MMC_ZX_H_
+#define _DW_MMC_ZX_H_
+
+/* ZX296718 SoC specific DLL register offset. */
+#define LB_AON_EMMC_CFG_REG0 0x1B0
+#define LB_AON_EMMC_CFG_REG1 0x1B4
+#define LB_AON_EMMC_CFG_REG2 0x1B8
+
+/* LB_AON_EMMC_CFG_REG0 register defines */
+#define PARA_DLL_START(x) ((x) & 0xFF)
+#define PARA_DLL_START_MASK 0xFF
+#define DLL_REG_SET BIT(8)
+#define PARA_DLL_LOCK_NUM(x) (((x) & 7) << 16)
+#define PARA_DLL_LOCK_NUM_MASK (7 << 16)
+#define PARA_PHASE_DET_SEL(x) (((x) & 7) << 20)
+#define PARA_PHASE_DET_SEL_MASK (7 << 20)
+#define PARA_DLL_BYPASS_MODE BIT(23)
+#define PARA_HALF_CLK_MODE BIT(24)
+
+/* LB_AON_EMMC_CFG_REG1 register defines */
+#define READ_DQS_DELAY(x) ((x) & 0x7F)
+#define READ_DQS_DELAY_MASK (0x7F)
+#define READ_DQS_BYPASS_MODE BIT(7)
+#define CLK_SAMP_DELAY(x) (((x) & 0x7F) << 8)
+#define CLK_SAMP_DELAY_MASK (0x7F << 8)
+#define CLK_SAMP_BYPASS_MODE BIT(15)
+
+/* LB_AON_EMMC_CFG_REG2 register defines */
+#define ZX_DLL_LOCKED BIT(2)
+
+#endif /* _DW_MMC_ZX_H_ */
--
1.9.1
^ permalink raw reply related [flat|nested] 7+ messages in thread* [PATCH v3 3/5] Documentation: synopsys-dw-mshc: add binding for fifo quirks
2016-11-03 13:31 [PATCH v3 0/5] Add intial support to DW MMC host on ZTE SoC Jun Nie
2016-11-03 13:31 ` [PATCH v3 1/5] mmc: dt-bindings: add ZTE ZX296718 MMC bindings Jun Nie
2016-11-03 13:31 ` [PATCH v3 2/5] mmc: zx: Initial support for ZX mmc controller Jun Nie
@ 2016-11-03 13:31 ` Jun Nie
2016-11-03 13:31 ` [PATCH v3 4/5] mmc: dw: Add fifo address property Jun Nie
2016-11-03 13:31 ` [PATCH v3 5/5] mmc: dw: Add fifo watermark alignment property Jun Nie
4 siblings, 0 replies; 7+ messages in thread
From: Jun Nie @ 2016-11-03 13:31 UTC (permalink / raw)
To: shawn.guo, xie.baoyou
Cc: ulf.hansson, jh80.chung, jason.liu, linux-mmc, Jun Nie
Add fifo-addr property and fifo-watermark-quirk property to
synopsys-dw-mshc bindings. It is intended to provide more
dt interface to support SoCs specific configuration.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
---
Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt | 13 +++++++++++++
1 file changed, 13 insertions(+)
diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
index 4e00e85..8bf2e41 100644
--- a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
+++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
@@ -76,6 +76,17 @@ Optional properties:
* broken-cd: as documented in mmc core bindings.
+* data-addr: Override fifo address with value provided by DT. The default FIFO reg
+ offset is assumed as 0x100 (version < 0x240A) and 0x200(version >= 0x240A) by
+ driver. If the controller does not follow this rule, please use this property
+ to set fifo address in device tree.
+
+* fifo-watermark-aligned: Data done irq is expected if data length is less than
+ watermark in PIO mode. But fifo watermark is requested to be aligned with data
+ length in some SoC so that TX/RX irq can be generated with data done irq. Add this
+ watermark quirk to mark this requirement and force fifo watermark setting
+ accordingly.
+
* vmmc-supply: The phandle to the regulator to use for vmmc. If this is
specified we'll defer probe until we can find this regulator.
@@ -103,6 +114,8 @@ board specific portions as listed below.
interrupts = <0 75 0>;
#address-cells = <1>;
#size-cells = <0>;
+ data-addr = <0x200>;
+ fifo-watermark-aligned;
};
[board specific internal DMA resources]
--
1.9.1
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH v3 4/5] mmc: dw: Add fifo address property
2016-11-03 13:31 [PATCH v3 0/5] Add intial support to DW MMC host on ZTE SoC Jun Nie
` (2 preceding siblings ...)
2016-11-03 13:31 ` [PATCH v3 3/5] Documentation: synopsys-dw-mshc: add binding for fifo quirks Jun Nie
@ 2016-11-03 13:31 ` Jun Nie
2016-11-03 13:31 ` [PATCH v3 5/5] mmc: dw: Add fifo watermark alignment property Jun Nie
4 siblings, 0 replies; 7+ messages in thread
From: Jun Nie @ 2016-11-03 13:31 UTC (permalink / raw)
To: shawn.guo, xie.baoyou
Cc: ulf.hansson, jh80.chung, jason.liu, linux-mmc, Jun Nie
The FIFO address may break default address assumption of 0x100
(version < 0x240A) and 0x200(version >= 0x240A) in current driver.
The new property is introduced to override fifo address via DT
node information.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
---
drivers/mmc/host/dw_mmc.c | 6 +++++-
include/linux/mmc/dw_mmc.h | 2 ++
2 files changed, 7 insertions(+), 1 deletion(-)
diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
index 1c9ee36..696b5e6 100644
--- a/drivers/mmc/host/dw_mmc.c
+++ b/drivers/mmc/host/dw_mmc.c
@@ -2955,6 +2955,8 @@ static struct dw_mci_board *dw_mci_parse_dt(struct dw_mci *host)
of_property_read_u32(np, "card-detect-delay", &pdata->detect_delay_ms);
+ of_property_read_u32(np, "data-addr", &host->data_addr_override);
+
if (!of_property_read_u32(np, "clock-frequency", &clock_frequency))
pdata->bus_hz = clock_frequency;
@@ -3158,7 +3160,9 @@ int dw_mci_probe(struct dw_mci *host)
host->verid = SDMMC_GET_VERID(mci_readl(host, VERID));
dev_info(host->dev, "Version ID is %04x\n", host->verid);
- if (host->verid < DW_MMC_240A)
+ if (host->data_addr_override)
+ host->fifo_reg = host->regs + host->data_addr_override;
+ else if (host->verid < DW_MMC_240A)
host->fifo_reg = host->regs + DATA_OFFSET;
else
host->fifo_reg = host->regs + DATA_240A_OFFSET;
diff --git a/include/linux/mmc/dw_mmc.h b/include/linux/mmc/dw_mmc.h
index f5af2bd..17cb95a 100644
--- a/include/linux/mmc/dw_mmc.h
+++ b/include/linux/mmc/dw_mmc.h
@@ -107,6 +107,7 @@ struct dw_mci_dma_slave {
* @ciu_clk: Pointer to card interface unit clock instance.
* @slot: Slots sharing this MMC controller.
* @fifo_depth: depth of FIFO.
+ * @data_addr_override: override fifo reg offset with this value.
* @data_shift: log2 of FIFO item size.
* @part_buf_start: Start index in part_buf.
* @part_buf_count: Bytes of partial data in part_buf.
@@ -154,6 +155,7 @@ struct dw_mci {
spinlock_t irq_lock;
void __iomem *regs;
void __iomem *fifo_reg;
+ u32 data_addr_override;
struct scatterlist *sg;
struct sg_mapping_iter sg_miter;
--
1.9.1
^ permalink raw reply related [flat|nested] 7+ messages in thread* [PATCH v3 5/5] mmc: dw: Add fifo watermark alignment property
2016-11-03 13:31 [PATCH v3 0/5] Add intial support to DW MMC host on ZTE SoC Jun Nie
` (3 preceding siblings ...)
2016-11-03 13:31 ` [PATCH v3 4/5] mmc: dw: Add fifo address property Jun Nie
@ 2016-11-03 13:31 ` Jun Nie
4 siblings, 0 replies; 7+ messages in thread
From: Jun Nie @ 2016-11-03 13:31 UTC (permalink / raw)
To: shawn.guo, xie.baoyou
Cc: ulf.hansson, jh80.chung, jason.liu, linux-mmc, Jun Nie
Data done irq is expected if data length is less than
watermark in PIO mode. But fifo watermark is requested
to be aligned with data length in some SoC so that TX/RX
irq can be generated with data done irq. Add the
watermark alignment to mark this requirement and force
fifo watermark setting accordingly.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
---
drivers/mmc/host/dw_mmc.c | 11 +++++++++--
include/linux/mmc/dw_mmc.h | 3 +++
2 files changed, 12 insertions(+), 2 deletions(-)
diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
index 696b5e6..6d85ca6 100644
--- a/drivers/mmc/host/dw_mmc.c
+++ b/drivers/mmc/host/dw_mmc.c
@@ -1111,11 +1111,15 @@ static void dw_mci_submit_data(struct dw_mci *host, struct mmc_data *data)
mci_writel(host, CTRL, temp);
/*
- * Use the initial fifoth_val for PIO mode.
+ * Use the initial fifoth_val for PIO mode. If wm_algined
+ * is set, we set watermark same as data size.
* If next issued data may be transfered by DMA mode,
* prev_blksz should be invalidated.
*/
- mci_writel(host, FIFOTH, host->fifoth_val);
+ if (host->wm_aligned)
+ dw_mci_adjust_fifoth(host, data);
+ else
+ mci_writel(host, FIFOTH, host->fifoth_val);
host->prev_blksz = 0;
} else {
/*
@@ -2957,6 +2961,9 @@ static struct dw_mci_board *dw_mci_parse_dt(struct dw_mci *host)
of_property_read_u32(np, "data-addr", &host->data_addr_override);
+ if (of_get_property(np, "fifo-watermark-aligned", NULL))
+ host->wm_aligned = true;
+
if (!of_property_read_u32(np, "clock-frequency", &clock_frequency))
pdata->bus_hz = clock_frequency;
diff --git a/include/linux/mmc/dw_mmc.h b/include/linux/mmc/dw_mmc.h
index 17cb95a..ee4bb30 100644
--- a/include/linux/mmc/dw_mmc.h
+++ b/include/linux/mmc/dw_mmc.h
@@ -108,6 +108,8 @@ struct dw_mci_dma_slave {
* @slot: Slots sharing this MMC controller.
* @fifo_depth: depth of FIFO.
* @data_addr_override: override fifo reg offset with this value.
+ * @wm_aligned: force fifo watermark equal with data length in PIO mode.
+ * Set as true if alignment is needed.
* @data_shift: log2 of FIFO item size.
* @part_buf_start: Start index in part_buf.
* @part_buf_count: Bytes of partial data in part_buf.
@@ -156,6 +158,7 @@ struct dw_mci {
void __iomem *regs;
void __iomem *fifo_reg;
u32 data_addr_override;
+ bool wm_aligned;
struct scatterlist *sg;
struct sg_mapping_iter sg_miter;
--
1.9.1
^ permalink raw reply related [flat|nested] 7+ messages in thread