From: Tony Lindgren <tony@atomide.com>
To: Balaji T K <balajitk@ti.com>
Cc: Andreas Fenkart <afenkart@gmail.com>,
Chris Ball <chris@printf.net>,
Grant Likely <grant.likely@secretlab.ca>,
Felipe Balbi <balbi@ti.com>,
Andreas Mueller <schnitzeltony@googlemail.com>,
Sebastian Reichel <sre@kernel.org>,
zonque@gmail.com, galak@codeaurora.org,
linux-doc@vger.kernel.org, linux-mmc@vger.kernel.org,
linux-omap@vger.kernel.org
Subject: Re: [PATCH v13 3/7] mmc: omap_hsmmc: Extend debugfs by SDIO IRQ handling, runtime state
Date: Fri, 23 May 2014 08:14:24 -0700 [thread overview]
Message-ID: <20140523151424.GG2321@atomide.com> (raw)
In-Reply-To: <537F3E6E.7060000@ti.com>
* Balaji T K <balajitk@ti.com> [140523 05:27]:
> On Friday 23 May 2014 02:00 PM, Andreas Fenkart wrote:
> >Add SDIO IRQ entries to debugfs entry. Note that PSTATE shows current
> >state of data lines, incl. SDIO IRQ pending
> >
> >Acked-by: Balaji T K <balajitk@ti.com>
> >Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
> >
> >diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c
> >index 0125eea..cfd2bfb 100644
> >--- a/drivers/mmc/host/omap_hsmmc.c
> >+++ b/drivers/mmc/host/omap_hsmmc.c
> >@@ -56,6 +56,7 @@
> > #define OMAP_HSMMC_RSP54 0x0118
> > #define OMAP_HSMMC_RSP76 0x011C
> > #define OMAP_HSMMC_DATA 0x0120
> >+#define OMAP_HSMMC_PSTATE 0x0124
> > #define OMAP_HSMMC_HCTL 0x0128
> > #define OMAP_HSMMC_SYSCTL 0x012C
> > #define OMAP_HSMMC_STAT 0x0130
> >@@ -1816,10 +1817,23 @@ static int omap_hsmmc_regs_show(struct seq_file *s, void *data)
> > {
> > struct mmc_host *mmc = s->private;
> > struct omap_hsmmc_host *host = mmc_priv(mmc);
> >+#ifdef CONFIG_PM
> >+ bool suspended;
> >+#endif
> >
> > seq_printf(s, "mmc%d:\n", mmc->index);
> >+ seq_printf(s, "sdio irq mode\t%s\n",
> >+ (mmc->caps & MMC_CAP_SDIO_IRQ) ? "interrupt" : "polling");
> >+
> >+ if (mmc->caps & MMC_CAP_SDIO_IRQ) {
> >+ seq_printf(s, "sdio irq \t%s\n",
> >+ (host->flags & HSMMC_SDIO_IRQ_ENABLED) ? "enabled"
> >+ : "disabled");
> >+ }
> >
> > #ifdef CONFIG_PM
>
> shouldn't this be CONFIG_PM_RUNTIME ?
>
> >+ suspended = host->dev->power.runtime_status != RPM_ACTIVE;
> >+ seq_printf(s, "runtime state\t%s\n", (suspended ? "idle" : "active"));
>
> The whole check for runtime status (and check for CONFIG_PM..) can be removed,
> since runtime status is available via sysfs
>
> cat /sys/class/mmc_host/mmc<X>/device/power/runtime_status
>
> > seq_printf(s, "ctx_loss:\t%d\n", host->context_loss);
> > #endif
Also CONFIG_SYSFS is a bool FYI.
Regards,
Tony
next prev parent reply other threads:[~2014-05-23 15:14 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-05-23 8:30 [PATCH v13 0/7] mmc: omap_hsmmc: Enable SDIO IRQ Andreas Fenkart
2014-05-23 8:30 ` [PATCH v13 1/7] mmc: omap_hsmmc: install dummy pm runtime hooks if !CONFIG_PM_RUNTIME Andreas Fenkart
2014-05-23 10:16 ` Balaji T K
2014-05-23 12:10 ` Andreas Fenkart
2014-05-23 8:30 ` [PATCH v13 2/7] mmc: omap_hsmmc: Enable SDIO interrupt Andreas Fenkart
2014-05-23 8:30 ` [PATCH v13 3/7] mmc: omap_hsmmc: Extend debugfs by SDIO IRQ handling, runtime state Andreas Fenkart
2014-05-23 12:26 ` Balaji T K
2014-05-23 15:14 ` Tony Lindgren [this message]
2014-05-23 8:30 ` [PATCH v13 4/7] mmc: omap_hsmmc: enable wakeup event for sdio OMAP4 Andreas Fenkart
2014-05-23 8:30 ` [PATCH v13 5/7] mmc: omap_hsmmc: abort runtime suspend if pending sdio irq detected Andreas Fenkart
2014-05-23 8:30 ` [PATCH v13 6/7] mmc: omap_hsmmc: switch default/idle pinctrl states in runtime hooks Andreas Fenkart
2014-05-23 8:30 ` [PATCH v13 7/7] mmc: omap_hsmmc: Pin remux workaround to support SDIO interrupt on AM335x Andreas Fenkart
2014-05-23 12:28 ` Balaji T K
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20140523151424.GG2321@atomide.com \
--to=tony@atomide.com \
--cc=afenkart@gmail.com \
--cc=balajitk@ti.com \
--cc=balbi@ti.com \
--cc=chris@printf.net \
--cc=galak@codeaurora.org \
--cc=grant.likely@secretlab.ca \
--cc=linux-doc@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=schnitzeltony@googlemail.com \
--cc=sre@kernel.org \
--cc=zonque@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).