From: Ludovic Desroches <ludovic.desroches@atmel.com>
To: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>,
linux-mmc <linux-mmc@vger.kernel.org>,
"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>,
Nicolas Ferre <nicolas.ferre@atmel.com>,
"linux-arm-kernel@lists.infradead.org"
<linux-arm-kernel@lists.infradead.org>
Subject: Re: [PATCH v2] mmc: sdhci at91: add PM support
Date: Tue, 10 Nov 2015 14:21:05 +0100 [thread overview]
Message-ID: <20151110132105.GF15706@odux.rfo.atmel.com> (raw)
In-Reply-To: <CAPDyKFoAwmkw0D8QbA4UV3uhhNS7hmfOiRv3ZUhMp8uoxzWnrw@mail.gmail.com>
On Tue, Nov 10, 2015 at 12:12:30PM +0100, Ulf Hansson wrote:
> On 10 November 2015 at 11:36, Ludovic Desroches
> <ludovic.desroches@atmel.com> wrote:
> > Add runtime PM support and use runtime_force_suspend|resume() for system
> > PM.
> >
> > Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
> > ---
> >
> > Changes:
> > - from v1: take a runtime PM centric approach
> >
> > drivers/mmc/host/sdhci-of-at91.c | 66 +++++++++++++++++++++++++++++++++++++++-
> > 1 file changed, 65 insertions(+), 1 deletion(-)
> >
> > diff --git a/drivers/mmc/host/sdhci-of-at91.c b/drivers/mmc/host/sdhci-of-at91.c
> > index 06d0b50..5dbe0ce 100644
> > --- a/drivers/mmc/host/sdhci-of-at91.c
> > +++ b/drivers/mmc/host/sdhci-of-at91.c
> > @@ -21,6 +21,8 @@
> > #include <linux/module.h>
> > #include <linux/of.h>
> > #include <linux/of_device.h>
> > +#include <linux/pm.h>
> > +#include <linux/pm_runtime.h>
> >
> > #include "sdhci-pltfm.h"
> >
> > @@ -51,6 +53,62 @@ static const struct of_device_id sdhci_at91_dt_match[] = {
> > {}
> > };
> >
> > +#ifdef CONFIG_PM
> > +static int sdhci_at91_runtime_suspend(struct device *dev)
> > +{
> > + struct platform_device *pdev = to_platform_device(dev);
> > + struct sdhci_host *host = platform_get_drvdata(pdev);
>
> These two lines can be replaced by:
> struct sdhci_host *host = dev_get_drvdata(dev);
>
Oh yes, trying to complicate things!
> > + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> > + struct sdhci_at91_priv *priv = pltfm_host->priv;
> > + int ret;
> > +
> > + ret = sdhci_runtime_suspend_host(host);
> > +
> > + clk_disable_unprepare(priv->gck);
> > + clk_disable_unprepare(priv->hclock);
> > + clk_disable_unprepare(priv->mainck);
> > +
> > + return ret;
> > +}
> > +
> > +static int sdhci_at91_runtime_resume(struct device *dev)
> > +{
> > + struct platform_device *pdev = to_platform_device(dev);
> > + struct sdhci_host *host = platform_get_drvdata(pdev);
>
> Same comment as above.
>
> > + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> > + struct sdhci_at91_priv *priv = pltfm_host->priv;
> > + int ret;
> > +
> > + ret = clk_prepare_enable(priv->mainck);
> > + if (ret) {
> > + dev_err(dev, "can't enable mainck\n");
> > + return ret;
> > + }
> > +
> > + ret = clk_prepare_enable(priv->hclock);
> > + if (ret) {
> > + dev_err(dev, "can't enable hclock\n");
> > + return ret;
> > + }
> > +
> > + ret = clk_prepare_enable(priv->gck);
> > + if (ret) {
> > + dev_err(dev, "can't enable gck\n");
> > + return ret;
> > + }
> > +
> > + return sdhci_runtime_resume_host(host);
> > +}
> > +#endif /* CONFIG_PM_RUNTIME */
>
> /s/CONFIG_PM_RUNTIME/CONFIG_PM
>
> > +
> > +static const struct dev_pm_ops sdhci_at91_dev_pm_ops = {
> > + SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
> > + pm_runtime_force_resume)
> > + SET_RUNTIME_PM_OPS(sdhci_at91_runtime_suspend,
> > + sdhci_at91_runtime_resume,
> > + NULL)
> > +};
> > +
> > static int sdhci_at91_probe(struct platform_device *pdev)
> > {
> > const struct of_device_id *match;
> > @@ -148,6 +206,11 @@ static int sdhci_at91_probe(struct platform_device *pdev)
> > if (ret)
> > goto clocks_disable_unprepare;
> >
> > + pm_runtime_set_active(&pdev->dev);
> > + pm_runtime_enable(&pdev->dev);
> > + pm_runtime_set_autosuspend_delay(&pdev->dev, 50);
> > + pm_runtime_use_autosuspend(&pdev->dev);
>
> Move these four runtime PM calls above sdhci_add_host(), as after that
> point the host is used and thus runtime PM operations starts.
>
Ok.
> > +
> > return 0;
> >
> > clocks_disable_unprepare:
> > @@ -165,6 +228,7 @@ static int sdhci_at91_remove(struct platform_device *pdev)
> > struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> > struct sdhci_at91_priv *priv = pltfm_host->priv;
> >
>
> Add:
> pm_runtime_get_sync();
>
> > + pm_runtime_disable(&pdev->dev);
>
> Add:
> pm_runtime_put_noidle();
>
This time I should complicate things a bit more.
> > sdhci_pltfm_unregister(pdev);
> >
> > clk_disable_unprepare(priv->gck);
> > @@ -178,7 +242,7 @@ static struct platform_driver sdhci_at91_driver = {
> > .driver = {
> > .name = "sdhci-at91",
> > .of_match_table = sdhci_at91_dt_match,
> > - .pm = SDHCI_PLTFM_PMOPS,
> > + .pm = &sdhci_at91_dev_pm_ops,
> > },
> > .probe = sdhci_at91_probe,
> > .remove = sdhci_at91_remove,
> > --
> > 2.5.0
> >
>
> Otherwise, this looks good!
Thanks for your feedback, v3 is coming.
Regards
Ludovic
next prev parent reply other threads:[~2015-11-10 13:21 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-11-10 10:36 [PATCH v2] mmc: sdhci at91: add PM support Ludovic Desroches
2015-11-10 11:12 ` Ulf Hansson
2015-11-10 13:21 ` Ludovic Desroches [this message]
2015-11-26 16:07 ` Ludovic Desroches
2015-11-26 16:24 ` Ulf Hansson
2015-11-26 16:32 ` Ludovic Desroches
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20151110132105.GF15706@odux.rfo.atmel.com \
--to=ludovic.desroches@atmel.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
--cc=nicolas.ferre@atmel.com \
--cc=ulf.hansson@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).