Re: [PATCH 1/2] dt-bindings: mmc: add DT bindings for Milbeaut SD controller

[<orito.takao@socionext.com>]

Thank you for reviewing my patches.
Sorry for my late reply. Japan was in Spring Vacation.

> On Fri, Apr 26, 2019 at 11:06:32AM +0900, Takao Orito wrote:
> 
> Needs a commit msg.

I see. I will add message.

> 
> > Signed-off-by: Takao Orito <orito.takao@socionext.com>
> > ---
> >  .../devicetree/bindings/mmc/sdhci-milbeaut.txt     | 35 ++++++++++++++++++++++
> >  1 file changed, 35 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/mmc/sdhci-milbeaut.txt
> > 
> > diff --git a/Documentation/devicetree/bindings/mmc/sdhci-milbeaut.txt b/Documentation/devicetree/bindings/mmc/sdhci-milbeaut.txt
> > new file mode 100644
> > index 0000000..7008462
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/mmc/sdhci-milbeaut.txt
> > @@ -0,0 +1,35 @@
> > +* SOCIONEXT SDHCI controller
> > +
> > +This file documents differences between the core properties in mmc.txt
> > +and the properties used by the sdhci_milbeaut driver.
> > +
> > +Required properties:
> > +- compatible: "socionext,milbeaut-m10v-sdhci-3.0"
> > +- clocks: Must contain an entry for each entry in clock-names. It is a
> > +  list of phandles and clock-specifier pairs.
> > +  See ../clocks/clock-bindings.txt for details.
> > +- clock-names: Should contain the following two entries:
> > +	"iface" - clock used for sdhci interface
> > +	"core"  - core clock for sdhci controller
> > +
> > +Optional properties:
> > +- vqmmc-supply: phandle to the regulator device tree node, mentioned
> > +  as the VCCQ/VDD_IO supply in the eMMC/SD specs.
> > +- fujitsu,cmd-dat-delay-select: boolean property indicating that this host
> > +  requires the CMD_DAT_DELAY control to be enabled.
> > +- sni,mmc-power-gpio: set property indicating that power on or off needs
> > +  control of gpios.
> > +
> > +Example:
> > +	sdhci3: mmc@1b010000 {
> > +		compatible = "socionext,milbeaut-m10v-sdhci-3.0";
> > +		reg = <0x1b010000 0x10000>;
> > +		interrupts = <0 265 0x4>;
> > +		voltage-ranges = <3300 3300>;
> > +		bus-width = <4>;
> > +		clocks = <&clk 7>, <&ahb_clk>;
> > +		clock-names = "core", "iface";
> > +		cap-sdio-irq;
> > +		sni,mmc-power-gpio = <&pinctrl 53 GPIO_ACTIVE_HIGH>;
> > +			fujitsu,cmd-dat-delay-select;
> 
> Whitespace problem.

Sorry, I will fix.

Thanks
Orito

> 
> > +	};
> > -- 
> > 1.9.1
> > 
> > 

-- 
Takao Orito <orito.takao@socionext.com>