[PATCH v2 13/19] mmc: sdricoh_cs: Throttle polling rate for commands

[PATCH v2 13/19] mmc: sdricoh_cs: Throttle polling rate for commands

[Ulf Hansson]

Rather than to poll in a busy-loop, let's convert into using
read_poll_timeout() and insert a small delay between each polling attempts.
In particular, this avoids hogging the CPU.

Additionally, to convert to read_poll_timeout() we also need to switch from
using a specific number of polling attempts, into a specific timeout in us
instead. The previous 100000 attempts, is translated into a total timeout
of total 1s, as that seemed like reasonable value to pick.

Cc: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
---

Changes in v2:
	- Use read_poll_timeout() instead of readl_poll_timeout(), as to
	preserve the debug print in sdricoh_readl().

---
 drivers/mmc/host/sdricoh_cs.c | 33 ++++++++++++++++-----------------
 1 file changed, 16 insertions(+), 17 deletions(-)

diff --git a/drivers/mmc/host/sdricoh_cs.c b/drivers/mmc/host/sdricoh_cs.c
index 8392158e2e9f..0594b5ffe151 100644
--- a/drivers/mmc/host/sdricoh_cs.c
+++ b/drivers/mmc/host/sdricoh_cs.c
@@ -59,7 +59,7 @@ static unsigned int switchlocked;
 #define STATUS_BUSY              0x40000000
 
 /* timeouts */
-#define CMD_TIMEOUT       100000
+#define SDRICOH_CMD_TIMEOUT_US	1000000
 #define SDRICOH_DATA_TIMEOUT_US	1000000
 
 /* list of supported pcmcia devices */
@@ -158,8 +158,7 @@ static int sdricoh_query_status(struct sdricoh_host *host, unsigned int wanted)
 static int sdricoh_mmc_cmd(struct sdricoh_host *host, struct mmc_command *cmd)
 {
 	unsigned int status;
-	int result = 0;
-	unsigned int loop = 0;
+	int ret;
 	unsigned char opcode = cmd->opcode;
 
 	/* reset status reg? */
@@ -175,24 +174,24 @@ static int sdricoh_mmc_cmd(struct sdricoh_host *host, struct mmc_command *cmd)
 	/* fill parameters */
 	sdricoh_writel(host, R204_CMD_ARG, cmd->arg);
 	sdricoh_writel(host, R200_CMD, (0x10000 << 8) | opcode);
+
 	/* wait for command completion */
-	if (opcode) {
-		for (loop = 0; loop < CMD_TIMEOUT; loop++) {
-			status = sdricoh_readl(host, R21C_STATUS);
-			sdricoh_writel(host, R2E4_STATUS_RESP, status);
-			if (status  & STATUS_CMD_FINISHED)
-				break;
-		}
-		/* don't check for timeout in the loop it is not always
-		   reset correctly
-		*/
-		if (loop == CMD_TIMEOUT || status & STATUS_CMD_TIMEOUT)
-			result = -ETIMEDOUT;
+	if (!opcode)
+		return 0;
 
-	}
+	ret = read_poll_timeout(sdricoh_readl, status,
+			sdricoh_status_ok(host, status, STATUS_CMD_FINISHED),
+			32, SDRICOH_CMD_TIMEOUT_US, false,
+			host, R21C_STATUS);
 
-	return result;
+	/*
+	 * Don't check for timeout status in the loop, as it's not always reset
+	 * correctly.
+	 */
+	if (ret || status & STATUS_CMD_TIMEOUT)
+		return -ETIMEDOUT;
 
+	return 0;
 }
 
 static int sdricoh_reset(struct sdricoh_host *host)
-- 
2.20.1