[PATCH AUTOSEL 5.14 203/252] mmc: sdhci-of-arasan: Modified SD default speed to 19MHz for ZynqMP

[PATCH AUTOSEL 5.14 203/252] mmc: sdhci-of-arasan: Modified SD default speed to 19MHz for ZynqMP

[Sasha Levin]

From: Manish Narani <manish.narani@xilinx.com>

[ Upstream commit c0b4e411a9b09748466ee06d2ae6772effa64dfb ]

SD standard speed timing was met only at 19MHz and not 25 MHz, that's
why changing driver to 19MHz. The reason for this is when a level shifter
is used on the board, timing was met for standard speed only at 19MHz.
Since this level shifter is commonly required for high speed modes,
the driver is modified to use standard speed of 19Mhz.

Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1623753837-21035-2-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/mmc/host/sdhci-of-arasan.c | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/drivers/mmc/host/sdhci-of-arasan.c b/drivers/mmc/host/sdhci-of-arasan.c
index 0e7c07ed9690..03c80c9bb7e3 100644
--- a/drivers/mmc/host/sdhci-of-arasan.c
+++ b/drivers/mmc/host/sdhci-of-arasan.c
@@ -159,6 +159,12 @@ struct sdhci_arasan_data {
 /* Controller immediately reports SDHCI_CLOCK_INT_STABLE after enabling the
  * internal clock even when the clock isn't stable */
 #define SDHCI_ARASAN_QUIRK_CLOCK_UNSTABLE BIT(1)
+/*
+ * Some of the Arasan variations might not have timing requirements
+ * met at 25MHz for Default Speed mode, those controllers work at
+ * 19MHz instead
+ */
+#define SDHCI_ARASAN_QUIRK_CLOCK_25_BROKEN BIT(2)
 };
 
 struct sdhci_arasan_of_data {
@@ -290,6 +296,16 @@ static void sdhci_arasan_set_clock(struct sdhci_host *host, unsigned int clock)
 		sdhci_arasan->is_phy_on = false;
 	}
 
+	if (sdhci_arasan->quirks & SDHCI_ARASAN_QUIRK_CLOCK_25_BROKEN) {
+		/*
+		 * Some of the Arasan variations might not have timing
+		 * requirements met at 25MHz for Default Speed mode,
+		 * those controllers work at 19MHz instead.
+		 */
+		if (clock == DEFAULT_SPEED_MAX_DTR)
+			clock = (DEFAULT_SPEED_MAX_DTR * 19) / 25;
+	}
+
 	/* Set the Input and Output Clock Phase Delays */
 	if (clk_data->set_clk_delays)
 		clk_data->set_clk_delays(host);
@@ -1608,6 +1624,8 @@ static int sdhci_arasan_probe(struct platform_device *pdev)
 	if (of_device_is_compatible(np, "xlnx,zynqmp-8.9a")) {
 		host->mmc_host_ops.execute_tuning =
 			arasan_zynqmp_execute_tuning;
+
+		sdhci_arasan->quirks |= SDHCI_ARASAN_QUIRK_CLOCK_25_BROKEN;
 	}
 
 	arasan_dt_parse_clk_phases(dev, &sdhci_arasan->clk_data);
-- 
2.30.2

[PATCH AUTOSEL 5.14 204/252] mmc: sdhci-of-arasan: Check return value of non-void funtions

[Sasha Levin]

From: Manish Narani <manish.narani@xilinx.com>

[ Upstream commit 66bad6ed2204fdb78a0a8fb89d824397106a5471 ]

At a couple of places, the return values of the non-void functions were
not getting checked. This was reported by the coverity tool. Modify the
code to check the return values of the same.

Addresses-Coverity: ("check_return")
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1623753837-21035-5-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/mmc/host/sdhci-of-arasan.c | 18 +++++++++++++++---
 1 file changed, 15 insertions(+), 3 deletions(-)

diff --git a/drivers/mmc/host/sdhci-of-arasan.c b/drivers/mmc/host/sdhci-of-arasan.c
index 03c80c9bb7e3..b6902447d779 100644
--- a/drivers/mmc/host/sdhci-of-arasan.c
+++ b/drivers/mmc/host/sdhci-of-arasan.c
@@ -273,7 +273,12 @@ static void sdhci_arasan_set_clock(struct sdhci_host *host, unsigned int clock)
 			 * through low speeds without power cycling.
 			 */
 			sdhci_set_clock(host, host->max_clk);
-			phy_power_on(sdhci_arasan->phy);
+			if (phy_power_on(sdhci_arasan->phy)) {
+				pr_err("%s: Cannot power on phy.\n",
+				       mmc_hostname(host->mmc));
+				return;
+			}
+
 			sdhci_arasan->is_phy_on = true;
 
 			/*
@@ -323,7 +328,12 @@ static void sdhci_arasan_set_clock(struct sdhci_host *host, unsigned int clock)
 		msleep(20);
 
 	if (ctrl_phy) {
-		phy_power_on(sdhci_arasan->phy);
+		if (phy_power_on(sdhci_arasan->phy)) {
+			pr_err("%s: Cannot power on phy.\n",
+			       mmc_hostname(host->mmc));
+			return;
+		}
+
 		sdhci_arasan->is_phy_on = true;
 	}
 }
@@ -479,7 +489,9 @@ static int sdhci_arasan_suspend(struct device *dev)
 		ret = phy_power_off(sdhci_arasan->phy);
 		if (ret) {
 			dev_err(dev, "Cannot power off phy.\n");
-			sdhci_resume_host(host);
+			if (sdhci_resume_host(host))
+				dev_err(dev, "Cannot resume host.\n");
+
 			return ret;
 		}
 		sdhci_arasan->is_phy_on = false;
-- 
2.30.2

[PATCH AUTOSEL 5.14 205/252] mmc: core: Avoid hogging the CPU while polling for busy in the I/O err path

[Sasha Levin]

From: Ulf Hansson <ulf.hansson@linaro.org>

[ Upstream commit 972d5084831dc9ae30f1a4b66cb4a19fb7ba6f09 ]

When mmc_blk_fix_state() sends a CMD12 to try to move the card into the
transfer state, it calls card_busy_detect() to poll for the card's state
with CMD13. This is done without any delays in between the commands being
sent.

Rather than fixing card_busy_detect() in this regards, let's instead
convert into using the common mmc_poll_for_busy(), which also helps us to
avoid open-coding.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210702134229.357717-2-ulf.hansson@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/mmc/core/block.c   | 2 +-
 drivers/mmc/core/mmc_ops.c | 4 +++-
 drivers/mmc/core/mmc_ops.h | 1 +
 3 files changed, 5 insertions(+), 2 deletions(-)

diff --git a/drivers/mmc/core/block.c b/drivers/mmc/core/block.c
index ce8aed562929..170343411f53 100644
--- a/drivers/mmc/core/block.c
+++ b/drivers/mmc/core/block.c
@@ -1636,7 +1636,7 @@ static int mmc_blk_fix_state(struct mmc_card *card, struct request *req)
 
 	mmc_blk_send_stop(card, timeout);
 
-	err = card_busy_detect(card, timeout, NULL);
+	err = mmc_poll_for_busy(card, timeout, false, MMC_BUSY_IO);
 
 	mmc_retune_release(card->host);
 
diff --git a/drivers/mmc/core/mmc_ops.c b/drivers/mmc/core/mmc_ops.c
index 973756ed4016..e2c431c0ce5d 100644
--- a/drivers/mmc/core/mmc_ops.c
+++ b/drivers/mmc/core/mmc_ops.c
@@ -435,7 +435,7 @@ static int mmc_busy_cb(void *cb_data, bool *busy)
 	u32 status = 0;
 	int err;
 
-	if (host->ops->card_busy) {
+	if (data->busy_cmd != MMC_BUSY_IO && host->ops->card_busy) {
 		*busy = host->ops->card_busy(host);
 		return 0;
 	}
@@ -457,6 +457,7 @@ static int mmc_busy_cb(void *cb_data, bool *busy)
 		break;
 	case MMC_BUSY_HPI:
 	case MMC_BUSY_EXTR_SINGLE:
+	case MMC_BUSY_IO:
 		break;
 	default:
 		err = -EINVAL;
@@ -521,6 +522,7 @@ int mmc_poll_for_busy(struct mmc_card *card, unsigned int timeout_ms,
 
 	return __mmc_poll_for_busy(card, timeout_ms, &mmc_busy_cb, &cb_data);
 }
+EXPORT_SYMBOL_GPL(mmc_poll_for_busy);
 
 bool mmc_prepare_busy_cmd(struct mmc_host *host, struct mmc_command *cmd,
 			  unsigned int timeout_ms)
diff --git a/drivers/mmc/core/mmc_ops.h b/drivers/mmc/core/mmc_ops.h
index 41ab4f573a31..ae25ffc2e870 100644
--- a/drivers/mmc/core/mmc_ops.h
+++ b/drivers/mmc/core/mmc_ops.h
@@ -15,6 +15,7 @@ enum mmc_busy_cmd {
 	MMC_BUSY_ERASE,
 	MMC_BUSY_HPI,
 	MMC_BUSY_EXTR_SINGLE,
+	MMC_BUSY_IO,
 };
 
 struct mmc_host;
-- 
2.30.2

[PATCH AUTOSEL 5.14 206/252] mmc: core: Avoid hogging the CPU while polling for busy for mmc ioctls

[Sasha Levin]

From: Ulf Hansson <ulf.hansson@linaro.org>

[ Upstream commit 468108155b0f89cc08189cc33f9bacfe9da8a125 ]

When __mmc_blk_ioctl_cmd() calls card_busy_detect() to verify that the
card's states moves back into transfer state, the polling with CMD13 is
done without any delays in between the commands being sent.

Rather than fixing card_busy_detect() in this regards, let's instead
convert into using the common mmc_poll_for_busy(), which also helps us to
avoid open-coding.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210702134229.357717-3-ulf.hansson@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/mmc/core/block.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/mmc/core/block.c b/drivers/mmc/core/block.c
index 170343411f53..c30d0ab15539 100644
--- a/drivers/mmc/core/block.c
+++ b/drivers/mmc/core/block.c
@@ -605,7 +605,8 @@ static int __mmc_blk_ioctl_cmd(struct mmc_card *card, struct mmc_blk_data *md,
 		 * Ensure RPMB/R1B command has completed by polling CMD13
 		 * "Send Status".
 		 */
-		err = card_busy_detect(card, MMC_BLK_TIMEOUT_MS, NULL);
+		err = mmc_poll_for_busy(card, MMC_BLK_TIMEOUT_MS, false,
+					MMC_BUSY_IO);
 	}
 
 	return err;
-- 
2.30.2

[PATCH AUTOSEL 5.14 207/252] mmc: core: Avoid hogging the CPU while polling for busy after I/O writes

[Sasha Levin]

From: Ulf Hansson <ulf.hansson@linaro.org>

[ Upstream commit 6966e6094c6d594044ef1b740dd827e05881331c ]

When mmc_blk_card_busy() calls card_busy_detect() to poll for the card's
state with CMD13, this is done without any delays in between the commands
being sent.

Rather than fixing card_busy_detect() in this regards, let's instead
convert into using the common __mmc_poll_for_busy(), which also helps us to
avoid open-coding.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210702134229.357717-4-ulf.hansson@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/mmc/core/block.c   | 69 ++++++++++++++++----------------------
 drivers/mmc/core/mmc_ops.c |  1 +
 2 files changed, 30 insertions(+), 40 deletions(-)

diff --git a/drivers/mmc/core/block.c b/drivers/mmc/core/block.c
index c30d0ab15539..a9ad9f5fa949 100644
--- a/drivers/mmc/core/block.c
+++ b/drivers/mmc/core/block.c
@@ -98,6 +98,11 @@ static int max_devices;
 static DEFINE_IDA(mmc_blk_ida);
 static DEFINE_IDA(mmc_rpmb_ida);
 
+struct mmc_blk_busy_data {
+	struct mmc_card *card;
+	u32 status;
+};
+
 /*
  * There is one mmc_blk_data per slot.
  */
@@ -417,42 +422,6 @@ static int mmc_blk_ioctl_copy_to_user(struct mmc_ioc_cmd __user *ic_ptr,
 	return 0;
 }
 
-static int card_busy_detect(struct mmc_card *card, unsigned int timeout_ms,
-			    u32 *resp_errs)
-{
-	unsigned long timeout = jiffies + msecs_to_jiffies(timeout_ms);
-	int err = 0;
-	u32 status;
-
-	do {
-		bool done = time_after(jiffies, timeout);
-
-		err = __mmc_send_status(card, &status, 5);
-		if (err) {
-			dev_err(mmc_dev(card->host),
-				"error %d requesting status\n", err);
-			return err;
-		}
-
-		/* Accumulate any response error bits seen */
-		if (resp_errs)
-			*resp_errs |= status;
-
-		/*
-		 * Timeout if the device never becomes ready for data and never
-		 * leaves the program state.
-		 */
-		if (done) {
-			dev_err(mmc_dev(card->host),
-				"Card stuck in wrong state! %s status: %#x\n",
-				 __func__, status);
-			return -ETIMEDOUT;
-		}
-	} while (!mmc_ready_for_data(status));
-
-	return err;
-}
-
 static int __mmc_blk_ioctl_cmd(struct mmc_card *card, struct mmc_blk_data *md,
 			       struct mmc_blk_ioc_data *idata)
 {
@@ -1852,28 +1821,48 @@ static inline bool mmc_blk_rq_error(struct mmc_blk_request *brq)
 	       brq->data.error || brq->cmd.resp[0] & CMD_ERRORS;
 }
 
+static int mmc_blk_busy_cb(void *cb_data, bool *busy)
+{
+	struct mmc_blk_busy_data *data = cb_data;
+	u32 status = 0;
+	int err;
+
+	err = mmc_send_status(data->card, &status);
+	if (err)
+		return err;
+
+	/* Accumulate response error bits. */
+	data->status |= status;
+
+	*busy = !mmc_ready_for_data(status);
+	return 0;
+}
+
 static int mmc_blk_card_busy(struct mmc_card *card, struct request *req)
 {
 	struct mmc_queue_req *mqrq = req_to_mmc_queue_req(req);
-	u32 status = 0;
+	struct mmc_blk_busy_data cb_data;
 	int err;
 
 	if (mmc_host_is_spi(card->host) || rq_data_dir(req) == READ)
 		return 0;
 
-	err = card_busy_detect(card, MMC_BLK_TIMEOUT_MS, &status);
+	cb_data.card = card;
+	cb_data.status = 0;
+	err = __mmc_poll_for_busy(card, MMC_BLK_TIMEOUT_MS, &mmc_blk_busy_cb,
+				  &cb_data);
 
 	/*
 	 * Do not assume data transferred correctly if there are any error bits
 	 * set.
 	 */
-	if (status & mmc_blk_stop_err_bits(&mqrq->brq)) {
+	if (cb_data.status & mmc_blk_stop_err_bits(&mqrq->brq)) {
 		mqrq->brq.data.bytes_xfered = 0;
 		err = err ? err : -EIO;
 	}
 
 	/* Copy the exception bit so it will be seen later on */
-	if (mmc_card_mmc(card) && status & R1_EXCEPTION_EVENT)
+	if (mmc_card_mmc(card) && cb_data.status & R1_EXCEPTION_EVENT)
 		mqrq->brq.cmd.resp[0] |= R1_EXCEPTION_EVENT;
 
 	return err;
diff --git a/drivers/mmc/core/mmc_ops.c b/drivers/mmc/core/mmc_ops.c
index e2c431c0ce5d..90d213a2203f 100644
--- a/drivers/mmc/core/mmc_ops.c
+++ b/drivers/mmc/core/mmc_ops.c
@@ -510,6 +510,7 @@ int __mmc_poll_for_busy(struct mmc_card *card, unsigned int timeout_ms,
 
 	return 0;
 }
+EXPORT_SYMBOL_GPL(__mmc_poll_for_busy);
 
 int mmc_poll_for_busy(struct mmc_card *card, unsigned int timeout_ms,
 		      bool retry_crc_err, enum mmc_busy_cmd busy_cmd)
-- 
2.30.2

[PATCH AUTOSEL 5.14 208/252] mmc: rtsx_pci: Fix long reads when clock is prescaled

[Sasha Levin]

From: Thomas Hebb <tommyhebb@gmail.com>

[ Upstream commit 3ac5e45291f3f0d699a721357380d4593bc2dcb3 ]

For unexplained reasons, the prescaler register for this device needs to
be cleared (set to 1) while performing a data read or else the command
will hang. This does not appear to affect the real clock rate sent out
on the bus, so I assume it's purely to work around a hardware bug.

During normal operation, the prescaler is already set to 1, so nothing
needs to be done. However, in "initial mode" (which is used for sub-MHz
clock speeds, like the core sets while enumerating cards), it's set to
128 and so we need to reset it during data reads. We currently fail to
do this for long reads.

This has no functional affect on the driver's operation currently
written, as the MMC core always sets a clock above 1MHz before
attempting any long reads. However, the core could conceivably set any
clock speed at any time and the driver should still work, so I think
this fix is worthwhile.

I personally encountered this issue while performing data recovery on an
external chip. My connections had poor signal integrity, so I modified
the core code to reduce the clock speed. Without this change, I saw the
card enumerate but was unable to actually read any data.

Writes don't seem to work in the situation described above even with
this change (and even if the workaround is extended to encompass data
write commands). I was not able to find a way to get them working.

Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Link: https://lore.kernel.org/r/2fef280d8409ab0100c26c6ac7050227defd098d.1627818365.git.tommyhebb@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/mmc/host/rtsx_pci_sdmmc.c | 36 ++++++++++++++++++++-----------
 1 file changed, 23 insertions(+), 13 deletions(-)

diff --git a/drivers/mmc/host/rtsx_pci_sdmmc.c b/drivers/mmc/host/rtsx_pci_sdmmc.c
index 4ca937415734..58cfaffa3c2d 100644
--- a/drivers/mmc/host/rtsx_pci_sdmmc.c
+++ b/drivers/mmc/host/rtsx_pci_sdmmc.c
@@ -542,9 +542,22 @@ static int sd_write_long_data(struct realtek_pci_sdmmc *host,
 	return 0;
 }
 
+static inline void sd_enable_initial_mode(struct realtek_pci_sdmmc *host)
+{
+	rtsx_pci_write_register(host->pcr, SD_CFG1,
+			SD_CLK_DIVIDE_MASK, SD_CLK_DIVIDE_128);
+}
+
+static inline void sd_disable_initial_mode(struct realtek_pci_sdmmc *host)
+{
+	rtsx_pci_write_register(host->pcr, SD_CFG1,
+			SD_CLK_DIVIDE_MASK, SD_CLK_DIVIDE_0);
+}
+
 static int sd_rw_multi(struct realtek_pci_sdmmc *host, struct mmc_request *mrq)
 {
 	struct mmc_data *data = mrq->data;
+	int err;
 
 	if (host->sg_count < 0) {
 		data->error = host->sg_count;
@@ -553,22 +566,19 @@ static int sd_rw_multi(struct realtek_pci_sdmmc *host, struct mmc_request *mrq)
 		return data->error;
 	}
 
-	if (data->flags & MMC_DATA_READ)
-		return sd_read_long_data(host, mrq);
+	if (data->flags & MMC_DATA_READ) {
+		if (host->initial_mode)
+			sd_disable_initial_mode(host);
 
-	return sd_write_long_data(host, mrq);
-}
+		err = sd_read_long_data(host, mrq);
 
-static inline void sd_enable_initial_mode(struct realtek_pci_sdmmc *host)
-{
-	rtsx_pci_write_register(host->pcr, SD_CFG1,
-			SD_CLK_DIVIDE_MASK, SD_CLK_DIVIDE_128);
-}
+		if (host->initial_mode)
+			sd_enable_initial_mode(host);
 
-static inline void sd_disable_initial_mode(struct realtek_pci_sdmmc *host)
-{
-	rtsx_pci_write_register(host->pcr, SD_CFG1,
-			SD_CLK_DIVIDE_MASK, SD_CLK_DIVIDE_0);
+		return err;
+	}
+
+	return sd_write_long_data(host, mrq);
 }
 
 static void sd_normal_rw(struct realtek_pci_sdmmc *host,
-- 
2.30.2

[PATCH AUTOSEL 5.14 211/252] mmc: core: Return correct emmc response in case of ioctl error

[Sasha Levin]

From: Nishad Kamdar <nishadkamdar@gmail.com>

[ Upstream commit e72a55f2e5ddcfb3dce0701caf925ce435b87682 ]

When a read/write command is sent via ioctl to the kernel,
and the command fails, the actual error response of the emmc
is not sent to the user.

IOCTL read/write tests are carried out using commands
17 (Single BLock Read), 24 (Single Block Write),
18 (Multi Block Read), 25 (Multi Block Write)

The tests are carried out on a 64Gb emmc device. All of these
tests try to access an "out of range" sector address (0x09B2FFFF).

It is seen that without the patch the response received by the user
is not OUT_OF_RANGE error (R1 response 31st bit is not set) as per
JEDEC specification. After applying the patch proper response is seen.
This is because the function returns without copying the response to
the user in case of failure. This patch fixes the issue.

Hence, this memcpy is required whether we get an error response or not.
Therefor it is moved up from the current position up to immediately
after we have called mmc_wait_for_req().

The test code and the output of only the CMD17 is included in the
commit to limit the message length.

CMD17 (Test Code Snippet):
==========================
        printf("Forming CMD%d\n", opt_idx);
        /*  single block read */
        cmd.blksz = 512;
        cmd.blocks = 1;
        cmd.write_flag = 0;
        cmd.opcode = 17;
        //cmd.arg = atoi(argv[3]);
        cmd.arg = 0x09B2FFFF;
        /* Expecting response R1B */
        cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_ADTC;

        memset(data, 0, sizeof(__u8) * 512);
        mmc_ioc_cmd_set_data(cmd, data);

        printf("Sending CMD%d: ARG[0x%08x]\n", opt_idx, cmd.arg);
        if(ioctl(fd, MMC_IOC_CMD, &cmd))
                perror("Error");

        printf("\nResponse: %08x\n", cmd.response[0]);

CMD17 (Output without patch):
=============================
test@test-LIVA-Z:~$ sudo ./mmc cmd_test /dev/mmcblk0 17
Entering the do_mmc_commands:Device: /dev/mmcblk0 nargs:4
Entering the do_mmc_commands:Device: /dev/mmcblk0 options[17, 0x09B2FFF]
Forming CMD17
Sending CMD17: ARG[0x09b2ffff]
Error: Connection timed out

Response: 00000000
(Incorrect response)

CMD17 (Output with patch):
==========================
test@test-LIVA-Z:~$ sudo ./mmc cmd_test /dev/mmcblk0 17
[sudo] password for test:
Entering the do_mmc_commands:Device: /dev/mmcblk0 nargs:4
Entering the do_mmc_commands:Device: /dev/mmcblk0 options[17, 09B2FFFF]
Forming CMD17
Sending CMD17: ARG[0x09b2ffff]
Error: Connection timed out

Response: 80000900
(Correct OUT_OF_ERROR response as per JEDEC specification)

Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20210824191726.8296-1-nishadkamdar@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/mmc/core/block.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/drivers/mmc/core/block.c b/drivers/mmc/core/block.c
index a9ad9f5fa949..c3ecec3f6ddc 100644
--- a/drivers/mmc/core/block.c
+++ b/drivers/mmc/core/block.c
@@ -518,6 +518,7 @@ static int __mmc_blk_ioctl_cmd(struct mmc_card *card, struct mmc_blk_data *md,
 		return mmc_sanitize(card, idata->ic.cmd_timeout_ms);
 
 	mmc_wait_for_req(card->host, &mrq);
+	memcpy(&idata->ic.response, cmd.resp, sizeof(cmd.resp));
 
 	if (cmd.error) {
 		dev_err(mmc_dev(card->host), "%s: cmd error %d\n",
@@ -567,8 +568,6 @@ static int __mmc_blk_ioctl_cmd(struct mmc_card *card, struct mmc_blk_data *md,
 	if (idata->ic.postsleep_min_us)
 		usleep_range(idata->ic.postsleep_min_us, idata->ic.postsleep_max_us);
 
-	memcpy(&(idata->ic.response), cmd.resp, sizeof(cmd.resp));
-
 	if (idata->rpmb || (cmd.flags & MMC_RSP_R1B) == MMC_RSP_R1B) {
 		/*
 		 * Ensure RPMB/R1B command has completed by polling CMD13
-- 
2.30.2