[PATCH 3/5] arm64: dts: qcom: lemans-evk: Extend peripheral and subsystem support

[Wasim Nazir <wasim.nazir@oss.qualcomm.com>]

Enhance the Qualcomm Lemans EVK board file to support essential
peripherals and improve overall hardware capabilities, as
outlined below:
  - Enable GPI (Generic Peripheral Interface) DMA-0/1/2 and QUPv3-0/2
    controllers to facilitate DMA and peripheral communication.
  - Add support for PCIe-0/1, including required regulators and PHYs,
    to enable high-speed external device connectivity.
  - Integrate the TCA9534 I/O expander via I2C to provide 8 additional
    GPIO lines for extended I/O functionality.
  - Enable the USB0 controller in device mode to support USB peripheral
    operations.
  - Activate remoteproc subsystems for supported DSPs such as Audio DSP,
    Compute DSP-0/1 and Generic DSP-0/1, along with their corresponding
    firmware.
  - Configure nvmem-layout on the I2C EEPROM to store data for Ethernet
    and other consumers.
  - Enable the QCA8081 2.5G Ethernet PHY on port-0 and expose the
    Ethernet MAC address via nvmem for network configuration.
    It depends on CONFIG_QCA808X_PHY to use QCA8081 PHY.
  - Add support for the Iris video decoder, including the required
    firmware, to enable video decoding capabilities.
  - Enable SD-card slot on SDHC.

Co-developed-by: Viken Dadhaniya <viken.dadhaniya@oss.qualcomm.com>
Signed-off-by: Viken Dadhaniya <viken.dadhaniya@oss.qualcomm.com>
Co-developed-by: Sushrut Shree Trivedi <quic_sushruts@quicinc.com>
Signed-off-by: Sushrut Shree Trivedi <quic_sushruts@quicinc.com>
Co-developed-by: Nirmesh Kumar Singh <quic_nkumarsi@quicinc.com>
Signed-off-by: Nirmesh Kumar Singh <quic_nkumarsi@quicinc.com>
Co-developed-by: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com>
Signed-off-by: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com>
Co-developed-by: Mohd Ayaan Anwar <quic_mohdayaa@quicinc.com>
Signed-off-by: Mohd Ayaan Anwar <quic_mohdayaa@quicinc.com>
Co-developed-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Co-developed-by: Monish Chunara <quic_mchunara@quicinc.com>
Signed-off-by: Monish Chunara <quic_mchunara@quicinc.com>
Co-developed-by: Vishal Kumar Pal <quic_vispal@quicinc.com>
Signed-off-by: Vishal Kumar Pal <quic_vispal@quicinc.com>
Signed-off-by: Wasim Nazir <wasim.nazir@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/lemans-evk.dts | 387 ++++++++++++++++++++++++++++++++
 1 file changed, 387 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/lemans-evk.dts b/arch/arm64/boot/dts/qcom/lemans-evk.dts
index 9e415012140b..642b66c4ad1e 100644
--- a/arch/arm64/boot/dts/qcom/lemans-evk.dts
+++ b/arch/arm64/boot/dts/qcom/lemans-evk.dts
@@ -16,7 +16,10 @@ / {
 	compatible = "qcom,lemans-evk", "qcom,qcs9100", "qcom,sa8775p";
 
 	aliases {
+		ethernet0 = &ethernet0;
+		mmc1 = &sdhc;
 		serial0 = &uart10;
+		serial1 = &uart17;
 	};
 
 	chosen {
@@ -46,6 +49,30 @@ edp1_connector_in: endpoint {
 			};
 		};
 	};
+
+	vmmc_sdc: regulator-vmmc-sdc {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmc_sdc";
+
+		regulator-min-microvolt = <2950000>;
+		regulator-max-microvolt = <2950000>;
+	};
+
+	vreg_sdc: regulator-vreg-sdc {
+		compatible = "regulator-gpio";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2950000>;
+		regulator-name = "vreg_sdc";
+		regulator-type = "voltage";
+
+		startup-delay-us = <100>;
+
+		gpios = <&expander1 7 GPIO_ACTIVE_HIGH>;
+
+		states = <1800000 0x1
+			  2950000 0x0>;
+	};
 };
 
 &apps_rsc {
@@ -277,6 +304,161 @@ vreg_l8e: ldo8 {
 	};
 };
 
+&ethernet0 {
+	phy-handle = <&hsgmii_phy0>;
+	phy-mode = "2500base-x";
+
+	pinctrl-0 = <&ethernet0_default>;
+	pinctrl-names = "default";
+
+	snps,mtl-rx-config = <&mtl_rx_setup>;
+	snps,mtl-tx-config = <&mtl_tx_setup>;
+	snps,ps-speed = <1000>;
+
+	nvmem-cells = <&mac_addr0>;
+	nvmem-cell-names = "mac-address";
+
+	status = "okay";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		hsgmii_phy0: ethernet-phy@1c {
+			compatible = "ethernet-phy-id004d.d101";
+			reg = <0x1c>;
+			reset-gpios = <&pmm8654au_2_gpios 8 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <11000>;
+			reset-deassert-us = <70000>;
+		};
+	};
+
+	mtl_rx_setup: rx-queues-config {
+		snps,rx-queues-to-use = <4>;
+		snps,rx-sched-sp;
+
+		queue0 {
+			snps,dcb-algorithm;
+			snps,map-to-dma-channel = <0x0>;
+			snps,route-up;
+			snps,priority = <0x1>;
+		};
+
+		queue1 {
+			snps,dcb-algorithm;
+			snps,map-to-dma-channel = <0x1>;
+			snps,route-ptp;
+		};
+
+		queue2 {
+			snps,avb-algorithm;
+			snps,map-to-dma-channel = <0x2>;
+			snps,route-avcp;
+		};
+
+		queue3 {
+			snps,avb-algorithm;
+			snps,map-to-dma-channel = <0x3>;
+			snps,priority = <0xc>;
+		};
+	};
+
+	mtl_tx_setup: tx-queues-config {
+		snps,tx-queues-to-use = <4>;
+
+		queue0 {
+			snps,dcb-algorithm;
+		};
+
+		queue1 {
+			snps,dcb-algorithm;
+		};
+
+		queue2 {
+			snps,avb-algorithm;
+			snps,send_slope = <0x1000>;
+			snps,idle_slope = <0x1000>;
+			snps,high_credit = <0x3e800>;
+			snps,low_credit = <0xffc18000>;
+		};
+
+		queue3 {
+			snps,avb-algorithm;
+			snps,send_slope = <0x1000>;
+			snps,idle_slope = <0x1000>;
+			snps,high_credit = <0x3e800>;
+			snps,low_credit = <0xffc18000>;
+		};
+	};
+};
+
+&gpi_dma0 {
+	status = "okay";
+};
+
+&gpi_dma1 {
+	status = "okay";
+};
+
+&gpi_dma2 {
+	status = "okay";
+};
+
+&i2c18 {
+	status = "okay";
+
+	expander0: pca953x@38 {
+		compatible = "ti,tca9538";
+		#gpio-cells = <2>;
+		gpio-controller;
+		reg = <0x38>;
+	};
+
+	expander1: pca953x@39 {
+		compatible = "ti,tca9538";
+		#gpio-cells = <2>;
+		gpio-controller;
+		reg = <0x39>;
+	};
+
+	expander2: pca953x@3a {
+		compatible = "ti,tca9538";
+		#gpio-cells = <2>;
+		gpio-controller;
+		reg = <0x3a>;
+	};
+
+	expander3: pca953x@3b {
+		compatible = "ti,tca9538";
+		#gpio-cells = <2>;
+		gpio-controller;
+		reg = <0x3b>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c256";
+		reg = <0x50>;
+		pagesize = <64>;
+
+		nvmem-layout {
+			compatible = "fixed-layout";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			mac_addr0: mac-addr@0 {
+				reg = <0x0 0x6>;
+			};
+		};
+	};
+};
+
+&iris {
+	firmware-name = "qcom/vpu/vpu30_p4_s6.mbn";
+
+	status = "okay";
+};
+
 &mdss0 {
 	status = "okay";
 };
@@ -323,14 +505,196 @@ &mdss0_dp1_phy {
 	status = "okay";
 };
 
+&pcie0 {
+	perst-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie0_default_state>;
+
+	status = "okay";
+};
+
+&pcie0_phy {
+	vdda-phy-supply = <&vreg_l5a>;
+	vdda-pll-supply = <&vreg_l1c>;
+
+	status = "okay";
+};
+
+&pcie1 {
+	perst-gpios = <&tlmm 4 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie1_default_state>;
+
+	status = "okay";
+};
+
+&pcie1_phy {
+	vdda-phy-supply = <&vreg_l5a>;
+	vdda-pll-supply = <&vreg_l1c>;
+
+	status = "okay";
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
 &qupv3_id_1 {
 	status = "okay";
 };
 
+&qupv3_id_2 {
+	status = "okay";
+};
+
+&remoteproc_adsp {
+	firmware-name = "qcom/sa8775p/adsp.mbn";
+
+	status = "okay";
+};
+
+&remoteproc_cdsp0 {
+	firmware-name = "qcom/sa8775p/cdsp0.mbn";
+
+	status = "okay";
+};
+
+&remoteproc_cdsp1 {
+	firmware-name = "qcom/sa8775p/cdsp1.mbn";
+
+	status = "okay";
+};
+
+&remoteproc_gpdsp0 {
+	firmware-name = "qcom/sa8775p/gpdsp0.mbn";
+
+	status = "okay";
+};
+
+&remoteproc_gpdsp1 {
+	firmware-name = "qcom/sa8775p/gpdsp1.mbn";
+
+	status = "okay";
+};
+
+&sdhc {
+	vmmc-supply = <&vmmc_sdc>;
+	vqmmc-supply = <&vreg_sdc>;
+
+	pinctrl-0 = <&sdc_default>, <&sd_cd>;
+	pinctrl-1 = <&sdc_sleep>, <&sd_cd>;
+	pinctrl-names = "default", "sleep";
+
+	power-domains = <&rpmhpd SA8775P_CX>;
+	operating-points-v2 = <&sdhc_opp_table>;
+
+	cd-gpios = <&tlmm 36 GPIO_ACTIVE_LOW>;
+
+	status = "okay";
+
+	sdhc_opp_table: opp-table {
+		compatible = "operating-points-v2";
+
+		opp-100000000 {
+			opp-hz = /bits/ 64 <100000000>;
+			required-opps = <&rpmhpd_opp_low_svs>;
+			opp-peak-kBps = <1800000 400000>;
+			opp-avg-kBps = <100000 0>;
+		};
+
+		opp-384000000 {
+			opp-hz = /bits/ 64 <384000000>;
+			required-opps = <&rpmhpd_opp_nom>;
+			opp-peak-kBps = <5400000 1600000>;
+			opp-avg-kBps = <390000 0>;
+		};
+	};
+};
+
+&serdes0 {
+	phy-supply = <&vreg_l5a>;
+
+	status = "okay";
+};
+
 &sleep_clk {
 	clock-frequency = <32768>;
 };
 
+&tlmm {
+	ethernet0_default: ethernet0-default-state {
+		ethernet0_mdc: ethernet0-mdc-pins {
+			pins = "gpio8";
+			function = "emac0_mdc";
+			drive-strength = <16>;
+			bias-pull-up;
+		};
+
+		ethernet0_mdio: ethernet0-mdio-pins {
+			pins = "gpio9";
+			function = "emac0_mdio";
+			drive-strength = <16>;
+			bias-pull-up;
+		};
+	};
+
+	pcie0_default_state: pcie0-default-state {
+		clkreq-pins {
+			pins = "gpio1";
+			function = "pcie0_clkreq";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		perst-pins {
+			pins = "gpio2";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+
+		wake-pins {
+			pins = "gpio0";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	pcie1_default_state: pcie1-default-state {
+		clkreq-pins {
+			pins = "gpio3";
+			function = "pcie1_clkreq";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		perst-pins {
+			pins = "gpio4";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+
+		wake-pins {
+			pins = "gpio5";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	sd_cd: sd-cd-state {
+		pins = "gpio36";
+		function = "gpio";
+		bias-pull-up;
+	};
+};
+
 &uart10 {
 	compatible = "qcom,geni-debug-uart";
 	pinctrl-0 = <&qup_uart10_default>;
@@ -356,6 +720,29 @@ &ufs_mem_phy {
 	status = "okay";
 };
 
+&usb_0 {
+	status = "okay";
+};
+
+&usb_0_dwc3 {
+	dr_mode = "peripheral";
+};
+
+&usb_0_hsphy {
+	vdda-pll-supply = <&vreg_l7a>;
+	vdda18-supply = <&vreg_l6c>;
+	vdda33-supply = <&vreg_l9a>;
+
+	status = "okay";
+};
+
+&usb_0_qmpphy {
+	vdda-phy-supply = <&vreg_l1c>;
+	vdda-pll-supply = <&vreg_l7a>;
+
+	status = "okay";
+};
+
 &xo_board_clk {
 	clock-frequency = <38400000>;
 };

-- 
2.51.0