From: Dinh Nguyen <dinh.linux@gmail.com>
To: Seungwon Jeon <tgih.jun@samsung.com>
Cc: dinguyen@altera.com, linux-arm-kernel@lists.infradead.org,
'Jaehoon Chung' <jh80.chung@samsung.com>,
'Arnd Bergmann' <arnd@arndb.de>,
'Olof Johansson' <olof@lixom.net>, 'Pavel Machek' <pavel@denx.de>,
linux-mmc@vger.kernel.org
Subject: Re: [PATCHv2 6/6] mmc: dw_mmc: Add support DW SD/MMC driver on SOCFPGA
Date: Mon, 20 May 2013 09:47:43 -0500 [thread overview]
Message-ID: <519A378F.7070409@gmail.com> (raw)
In-Reply-To: <000a01ce551c$7b174190$7145c4b0$%jun@samsung.com>
Hi Seungwon,
On 05/20/2013 12:40 AM, Seungwon Jeon wrote:
> On 05/17/13 4:05, Dinh Nguyen wrote:
>> From: Dinh Nguyen <dinguyen@altera.com>
>>
>> Add platform specific functionality for the DW SD/MMC driver for
>> SoCFPGA. Move SDMMC_CMD_USE_HOLD_REG to dw_mmc.h so other platforms
>> can use this define.
>>
>> Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
>> CC: Seungwon Jeon <tgih.jun@samsung.com>
>> CC: Jaehoon Chung <jh80.chung@samsung.com>
>> CC: Arnd Bergmann <arnd@arndb.de>
>> CC: Olof Johansson <olof@lixom.net>
>> CC: Pavel Machek <pavel@denx.de>
>> CC: linux-mmc@vger.kernel.org
>>
>> v2:
>> - Use syscon and regmap
>> - Avoid divide by zero
>> - Remove the need to set PWR_EN
>> ---
>> drivers/mmc/host/Kconfig | 8 +++
>> drivers/mmc/host/Makefile | 1 +
>> drivers/mmc/host/dw_mmc-exynos.c | 2 -
>> drivers/mmc/host/dw_mmc-socfpga.c | 139 +++++++++++++++++++++++++++++++++++++
>> drivers/mmc/host/dw_mmc.h | 1 +
>> 5 files changed, 149 insertions(+), 2 deletions(-)
>> create mode 100644 drivers/mmc/host/dw_mmc-socfpga.c
>>
>> diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
>> index 9ab8f8d..1be2289 100644
>> --- a/drivers/mmc/host/Kconfig
>> +++ b/drivers/mmc/host/Kconfig
>> @@ -556,6 +556,14 @@ config MMC_DW_EXYNOS
>> Synopsys DesignWare Memory Card Interface driver. Select this option
>> for platforms based on Exynos4 and Exynos5 SoC's.
>>
>> +config MMC_DW_SOCFPGA
>> + tristate "SOCFPGA specific extensions for Synopsys DW Memory Card Interface"
>> + depends on MMC_DW
>> + select MMC_DW_PLTFM
>> + help
>> + This selects support for Altera SoCFPGA specific extensions to the
>> + Synopsys DesignWare Memory Card Interface driver.
>> +
>> config MMC_DW_PCI
>> tristate "Synopsys Designware MCI support on PCI bus"
>> depends on MMC_DW && PCI
>> diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
>> index cd32280..67718c1 100644
>> --- a/drivers/mmc/host/Makefile
>> +++ b/drivers/mmc/host/Makefile
>> @@ -42,6 +42,7 @@ obj-$(CONFIG_SDH_BFIN) += bfin_sdh.o
>> obj-$(CONFIG_MMC_DW) += dw_mmc.o
>> obj-$(CONFIG_MMC_DW_PLTFM) += dw_mmc-pltfm.o
>> obj-$(CONFIG_MMC_DW_EXYNOS) += dw_mmc-exynos.o
>> +obj-$(CONFIG_MMC_DW_SOCFPGA) += dw_mmc-socfpga.o
>> obj-$(CONFIG_MMC_DW_PCI) += dw_mmc-pci.o
>> obj-$(CONFIG_MMC_SH_MMCIF) += sh_mmcif.o
>> obj-$(CONFIG_MMC_JZ4740) += jz4740_mmc.o
>> diff --git a/drivers/mmc/host/dw_mmc-exynos.c b/drivers/mmc/host/dw_mmc-exynos.c
>> index f013e7e..866edef 100644
>> --- a/drivers/mmc/host/dw_mmc-exynos.c
>> +++ b/drivers/mmc/host/dw_mmc-exynos.c
>> @@ -31,8 +31,6 @@
>> SDMMC_CLKSEL_CCLK_DRIVE(y) | \
>> SDMMC_CLKSEL_CCLK_DIVIDER(z))
>>
>> -#define SDMMC_CMD_USE_HOLD_REG BIT(29)
>> -
>> #define EXYNOS4210_FIXED_CIU_CLK_DIV 2
>> #define EXYNOS4412_FIXED_CIU_CLK_DIV 4
>>
>> diff --git a/drivers/mmc/host/dw_mmc-socfpga.c b/drivers/mmc/host/dw_mmc-socfpga.c
>> new file mode 100644
>> index 0000000..af89685
>> --- /dev/null
>> +++ b/drivers/mmc/host/dw_mmc-socfpga.c
>> @@ -0,0 +1,139 @@
>> +/*
>> + * Altera SoCFPGA Specific Extensions for Synopsys DW Multimedia Card Interface driver
>> + *
>> + * Copyright (C) 2012, Samsung Electronics Co., Ltd.
>> + * Copyright (C) 2013 Altera Corporation
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License as published by
>> + * the Free Software Foundation; either version 2 of the License, or
>> + * (at your option) any later version.
>> + *
>> + * Taken from dw_mmc_exynos.c
>> + */
>> +#include <linux/clk.h>
>> +#include <linux/mfd/syscon.h>
>> +#include <linux/mmc/host.h>
>> +#include <linux/mmc/dw_mmc.h>
>> +#include <linux/module.h>
>> +#include <linux/of.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/regmap.h>
>> +
>> +#include "dw_mmc.h"
>> +#include "dw_mmc-pltfm.h"
>> +
>> +#define SYSMGR_SDMMCGRP_CTRL_OFFSET 0x108
>> +#define DRV_CLK_PHASE_SHIFT_SEL_MASK 0x7
>> +#define SYSMGR_SDMMC_CTRL_SET(smplsel, drvsel) \
>> + ((((drvsel) << 0) & 0x7) | (((smplsel) << 3) & 0x38))
> Did you check Jaehoon Chung's comment?
> It's trivial, but more common.
> ((((smplsel) & 0x38) << 3) | (((drvsel) & 0x7) << 0))
>
Yes, I missed the comment. Will change in rev3.
>> +
>> +extern void __iomem *sys_manager_base_addr;
>> +
>> +/* SOCFPGA implementation specific driver private data */
>> +struct dw_mci_socfpga_priv_data {
>> + u8 ciu_div;
>> + u32 hs_timing;
>> + struct regmap *sysreg;
>> +};
>> +
>> +static int dw_mci_socfpga_priv_init(struct dw_mci *host)
>> +{
>> + struct dw_mci_socfpga_priv_data *priv;
>> + struct device *dev = host->dev;
>> +
>> + priv = devm_kzalloc(host->dev, sizeof(*priv), GFP_KERNEL);
>> + if (!priv) {
>> + dev_err(host->dev, "mem alloc failed for private data\n");
>> + return -ENOMEM;
>> + }
>> +
>> + host->priv = priv;
>> + return 0;
>> +}
>> +
>> +static int dw_mci_socfpga_setup_clock(struct dw_mci *host)
>> +{
>> + struct dw_mci_socfpga_priv_data *priv = host->priv;
>> +
>> + clk_disable(host->ciu_clk);
>> + regmap_write(priv->sysreg, SYSMGR_SDMMCGRP_CTRL_OFFSET, priv->hs_timing);
>> + clk_enable(host->ciu_clk);
> You can use clk_prepare_enable/clk_disable_unprepare instead of clk_enable/clk_disable.
>
OK.
>> +
>> + host->bus_hz /= (priv->ciu_div + 1);
>> + return 0;
>> +}
>> +
>> +static void dw_mci_socfpga_prepare_command(struct dw_mci *host, u32 *cmdr)
>> +{
>> + struct dw_mci_socfpga_priv_data *priv = host->priv;
>> +
>> + if (priv->hs_timing & DRV_CLK_PHASE_SHIFT_SEL_MASK)
>> + *cmdr |= SDMMC_CMD_USE_HOLD_REG;
>> +}
>> +
>> +static int dw_mci_socfpga_parse_dt(struct dw_mci *host)
>> +{
>> + struct dw_mci_socfpga_priv_data *priv = host->priv;
>> + struct device_node *np = host->dev->of_node;
>> + u32 timing[2];
>> + u32 div = 0;
>> + int ret;
>> +
>> + priv->sysreg = syscon_regmap_lookup_by_compatible("altr,sys-mgr");
> How about placing syscon_regmap_lookup_by_compatible in dw_mci_socfpga_priv_init.
> It seems more proper place.
>
Ok, will move.
>> + if (IS_ERR(priv->sysreg)) {
>> + dev_err(host->dev, "regmap for altr,sys-mgr lookup failed.\n");
>> + return PTR_ERR(priv->sysreg);
>> + }
>> +
>> + of_property_read_u32(np, "altr,dw-mshc-ciu-div", &div);
> Error check would be helpful.
> ret = of_property_read_u32();
>
> Thanks,
> Seungwon Jeon
>
Thanks for the review.
Dinh
>> + priv->ciu_div = div;
>> +
>> + ret = of_property_read_u32_array(np,
>> + "altr,dw-mshc-sdr-timing", timing, 2);
>> + if (ret)
>> + return ret;
>> +
>> + priv->hs_timing = SYSMGR_SDMMC_CTRL_SET(timing[0], timing[1]);
>> + return 0;
>> +}
>> +
>> +static const struct dw_mci_drv_data socfpga_drv_data = {
>> + .init = dw_mci_socfpga_priv_init,
>> + .setup_clock = dw_mci_socfpga_setup_clock,
>> + .prepare_command = dw_mci_socfpga_prepare_command,
>> + .parse_dt = dw_mci_socfpga_parse_dt,
>> +};
>> +
>> +static const struct of_device_id dw_mci_socfpga_match[] = {
>> + { .compatible = "altr,socfpga-dw-mshc",
>> + .data = &socfpga_drv_data, },
>> + {},
>> +};
>> +MODULE_DEVICE_TABLE(of, dw_mci_socfpga_match);
>> +
>> +int dw_mci_socfpga_probe(struct platform_device *pdev)
>> +{
>> + const struct dw_mci_drv_data *drv_data;
>> + const struct of_device_id *match;
>> +
>> + match = of_match_node(dw_mci_socfpga_match, pdev->dev.of_node);
>> + drv_data = match->data;
>> + return dw_mci_pltfm_register(pdev, drv_data);
>> +}
>> +
>> +static struct platform_driver dw_mci_socfpga_pltfm_driver = {
>> + .probe = dw_mci_socfpga_probe,
>> + .remove = __exit_p(dw_mci_pltfm_remove),
>> + .driver = {
>> + .name = "dwmmc_socfpga",
>> + .of_match_table = of_match_ptr(dw_mci_socfpga_match),
>> + .pm = &dw_mci_pltfm_pmops,
>> + },
>> +};
>> +
>> +module_platform_driver(dw_mci_socfpga_pltfm_driver);
>> +
>> +MODULE_DESCRIPTION("Altera SOCFPGA Specific DW-MSHC Driver Extension");
>> +MODULE_LICENSE("GPL v2");
>> +MODULE_ALIAS("platform:dwmmc-socfpga");
>> diff --git a/drivers/mmc/host/dw_mmc.h b/drivers/mmc/host/dw_mmc.h
>> index 0b74189..3700cb2 100644
>> --- a/drivers/mmc/host/dw_mmc.h
>> +++ b/drivers/mmc/host/dw_mmc.h
>> @@ -111,6 +111,7 @@
>> #define SDMMC_INT_ERROR 0xbfc2
>> /* Command register defines */
>> #define SDMMC_CMD_START BIT(31)
>> +#define SDMMC_CMD_USE_HOLD_REG BIT(29)
>> #define SDMMC_CMD_CCS_EXP BIT(23)
>> #define SDMMC_CMD_CEATA_RD BIT(22)
>> #define SDMMC_CMD_UPD_CLK BIT(21)
>> --
>> 1.7.9.5
>>
>>
>> --
>> To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
>> the body of a message to majordomo@vger.kernel.org
>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
prev parent reply other threads:[~2013-05-20 14:47 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <1368731117-4749-1-git-send-email-dinguyen@altera.com>
2013-05-16 19:05 ` [PATCHv2 6/6] mmc: dw_mmc: Add support DW SD/MMC driver on SOCFPGA dinguyen
2013-05-17 11:46 ` Pavel Machek
2013-05-20 14:40 ` Dinh Nguyen
2013-05-20 5:40 ` Seungwon Jeon
2013-05-20 14:47 ` Dinh Nguyen [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=519A378F.7070409@gmail.com \
--to=dinh.linux@gmail.com \
--cc=arnd@arndb.de \
--cc=dinguyen@altera.com \
--cc=jh80.chung@samsung.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-mmc@vger.kernel.org \
--cc=olof@lixom.net \
--cc=pavel@denx.de \
--cc=tgih.jun@samsung.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).