From: Jaehoon Chung <jh80.chung@samsung.com>
To: dinguyen@altera.com
Cc: dinh.linux@gmail.com, Arnd Bergmann <arnd@arndb.de>,
Olof Johansson <olof@lixom.net>,
Jaehoon Chung <jh80.chung@samsung.com>,
Seungwon Jeon <tgih.jun@samsung.com>,
Rob Herring <rob.herring@calxeda.com>,
Pawel Moll <pawel.moll@arm.com>,
Mark Rutland <mark.rutland@arm.com>,
Stephen Warren <swarren@wwwdotorg.org>,
Ian Campbell <ian.campbell@citrix.com>,
devicetree@vger.kernel.org, linux-mmc@vger.kernel.org,
linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH] mmc: dw_mmc-exynos: Common bindings for dw-mshc timing
Date: Fri, 09 Aug 2013 11:54:01 +0900 [thread overview]
Message-ID: <520459C9.8020305@samsung.com> (raw)
In-Reply-To: <1376002520-7461-1-git-send-email-dinguyen@altera.com>
Hi Dinh
On 08/09/2013 07:55 AM, dinguyen@altera.com wrote:
> From: Dinh Nguyen <dinguyen@altera.com>
>
> Remove the "samsung" in "samsung,dw-mshc-ciu-div", "samsung,dw-mshc-sdr-timing",
> and "samsung,dw-mshc-ddr-timing". These characteristics are not applicable to
> just Samsung platforms, but to any platform that uses the Synopsis SD/MMC IP.
>
> Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
> CC: Arnd Bergmann <arnd@arndb.de>
> Cc: Olof Johansson <olof@lixom.net>
> Cc: Jaehoon Chung <jh80.chung@samsung.com>
> Cc: Seungwon Jeon <tgih.jun@samsung.com>
> Cc: Rob Herring <rob.herring@calxeda.com>
> Cc: Pawel Moll <pawel.moll@arm.com>
> Cc: Mark Rutland <mark.rutland@arm.com>
> Cc: Stephen Warren <swarren@wwwdotorg.org>
> Cc: Ian Campbell <ian.campbell@citrix.com>
> Cc: devicetree@vger.kernel.org
> Cc: linux-mmc@vger.kernel.org
> CC: linux-arm-kernel@lists.infradead.org
> ---
> .../devicetree/bindings/mmc/exynos-dw-mshc.txt | 30 --------------------
> .../devicetree/bindings/mmc/synopsis-dw-mshc.txt | 29 +++++++++++++++++++
> arch/arm/boot/dts/cros5250-common.dtsi | 18 ++++++------
> arch/arm/boot/dts/exynos4412-odroidx.dts | 6 ++--
> arch/arm/boot/dts/exynos4412-origen.dts | 6 ++--
> arch/arm/boot/dts/exynos5250-arndale.dts | 12 ++++----
> arch/arm/boot/dts/exynos5250-smdk5250.dts | 12 ++++----
> drivers/mmc/host/dw_mmc-exynos.c | 6 ++--
> 8 files changed, 59 insertions(+), 60 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt
> index 6d1c098..ddb1d95 100644
> --- a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt
> +++ b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt
> @@ -17,33 +17,6 @@ Required Properties:
> - "samsung,exynos5250-dw-mshc": for controllers with Samsung Exynos5250
> specific extensions.
>
> -* samsung,dw-mshc-ciu-div: Specifies the divider value for the card interface
> - unit (ciu) clock. This property is applicable only for Exynos5 SoC's and
> - ignored for Exynos4 SoC's. The valid range of divider value is 0 to 7.
> -
> -* samsung,dw-mshc-sdr-timing: Specifies the value of CIU clock phase shift value
> - in transmit mode and CIU clock phase shift value in receive mode for single
> - data rate mode operation. Refer notes below for the order of the cells and the
> - valid values.
> -
> -* samsung,dw-mshc-ddr-timing: Specifies the value of CUI clock phase shift value
> - in transmit mode and CIU clock phase shift value in receive mode for double
> - data rate mode operation. Refer notes below for the order of the cells and the
> - valid values.
> -
> - Notes for the sdr-timing and ddr-timing values:
> -
> - The order of the cells should be
> - - First Cell: CIU clock phase shift value for tx mode.
> - - Second Cell: CIU clock phase shift value for rx mode.
> -
> - Valid values for SDR and DDR CIU clock timing for Exynos5250:
> - - valid value for tx phase shift and rx phase shift is 0 to 7.
> - - when CIU clock divider value is set to 3, all possible 8 phase shift
> - values can be used.
> - - if CIU clock divider value is 0 (that is divide by 1), both tx and rx
> - phase shift clocks should be 0.
> -
> Required properties for a slot:
>
> * gpios: specifies a list of gpios used for command, clock and data bus. The
> @@ -71,9 +44,6 @@ Example:
> broken-cd;
> fifo-depth = <0x80>;
> card-detect-delay = <200>;
> - samsung,dw-mshc-ciu-div = <3>;
> - samsung,dw-mshc-sdr-timing = <2 3>;
> - samsung,dw-mshc-ddr-timing = <1 2>;
>
> slot@0 {
> reg = <0>;
> diff --git a/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt
> index cdcebea..cf85a8c 100644
> --- a/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt
> +++ b/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt
> @@ -71,6 +71,32 @@ Optional properties:
> * vmmc-supply: The phandle to the regulator to use for vmmc. If this is
> specified we'll defer probe until we can find this regulator.
>
> +* dw-mshc-ciu-div: Specifies the divider value for the card interface
> + unit (ciu) clock. The valid range of divider value is 0 to 7.
> +
> +* dw-mshc-sdr-timing: Specifies the value of CIU clock phase shift value
> + in transmit mode and CIU clock phase shift value in receive mode for single
> + data rate mode operation. Refer notes below for the order of the cells and the
> + valid values.
> +
> +* dw-mshc-ddr-timing: Specifies the value of CUI clock phase shift value
> + in transmit mode and CIU clock phase shift value in receive mode for double
> + data rate mode operation. Refer notes below for the order of the cells and the
> + valid values.
> +
> + Notes for the sdr-timing and ddr-timing values:
> +
> + The order of the cells should be
> + - First Cell: CIU clock phase shift value for tx mode.
> + - Second Cell: CIU clock phase shift value for rx mode.
> +
> + Valid values for SDR and DDR CIU clock timing for Exynos5250:
Exynos5250? Maybe It should be mentioned common SoC.
> + - valid value for tx phase shift and rx phase shift is 0 to 7.
> + - when CIU clock divider value is set to 3, all possible 8 phase shift
> + values can be used.
> + - if CIU clock divider value is 0 (that is divide by 1), both tx and rx
> + phase shift clocks should be 0.
> +
> Aliases:
>
> - All the MSHC controller nodes should be represented in the aliases node using
> @@ -99,6 +125,9 @@ board specific portions as listed below.
> fifo-depth = <0x80>;
> card-detect-delay = <200>;
> vmmc-supply = <&buck8>;
> + dw-mshc-ciu-div = <3>;
> + dw-mshc-sdr-timing = <2 3>;
> + dw-mshc-ddr-timing = <1 2>;
>
> slot@0 {
> reg = <0>;
> diff --git a/arch/arm/boot/dts/cros5250-common.dtsi b/arch/arm/boot/dts/cros5250-common.dtsi
> index dc259e8b..93d3c85 100644
> --- a/arch/arm/boot/dts/cros5250-common.dtsi
> +++ b/arch/arm/boot/dts/cros5250-common.dtsi
> @@ -235,9 +235,9 @@
> broken-cd;
> fifo-depth = <0x80>;
> card-detect-delay = <200>;
> - samsung,dw-mshc-ciu-div = <3>;
> - samsung,dw-mshc-sdr-timing = <2 3>;
> - samsung,dw-mshc-ddr-timing = <1 2>;
> + dw-mshc-ciu-div = <3>;
> + dw-mshc-sdr-timing = <2 3>;
> + dw-mshc-ddr-timing = <1 2>;
> pinctrl-names = "default";
> pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_cd &sd0_bus4 &sd0_bus8>;
>
> @@ -256,9 +256,9 @@
> supports-highspeed;
> fifo-depth = <0x80>;
> card-detect-delay = <200>;
> - samsung,dw-mshc-ciu-div = <3>;
> - samsung,dw-mshc-sdr-timing = <2 3>;
> - samsung,dw-mshc-ddr-timing = <1 2>;
> + dw-mshc-ciu-div = <3>;
> + dw-mshc-sdr-timing = <2 3>;
> + dw-mshc-ddr-timing = <1 2>;
> pinctrl-names = "default";
> pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
>
> @@ -275,9 +275,9 @@
> broken-cd;
> fifo-depth = <0x80>;
> card-detect-delay = <200>;
> - samsung,dw-mshc-ciu-div = <3>;
> - samsung,dw-mshc-sdr-timing = <2 3>;
> - samsung,dw-mshc-ddr-timing = <1 2>;
> + dw-mshc-ciu-div = <3>;
> + dw-mshc-sdr-timing = <2 3>;
> + dw-mshc-ddr-timing = <1 2>;
> /* See board-specific dts files for pin setup */
>
> slot@0 {
> diff --git a/arch/arm/boot/dts/exynos4412-odroidx.dts b/arch/arm/boot/dts/exynos4412-odroidx.dts
> index 46c678e..e6c3b23 100644
> --- a/arch/arm/boot/dts/exynos4412-odroidx.dts
> +++ b/arch/arm/boot/dts/exynos4412-odroidx.dts
> @@ -51,9 +51,9 @@
> broken-cd;
> fifo-depth = <0x80>;
> card-detect-delay = <200>;
> - samsung,dw-mshc-ciu-div = <3>;
> - samsung,dw-mshc-sdr-timing = <2 3>;
> - samsung,dw-mshc-ddr-timing = <1 2>;
> + dw-mshc-ciu-div = <3>;
> + dw-mshc-sdr-timing = <2 3>;
> + dw-mshc-ddr-timing = <1 2>;
>
> slot@0 {
> reg = <0>;
> diff --git a/arch/arm/boot/dts/exynos4412-origen.dts b/arch/arm/boot/dts/exynos4412-origen.dts
> index 7993641..b403a57 100644
> --- a/arch/arm/boot/dts/exynos4412-origen.dts
> +++ b/arch/arm/boot/dts/exynos4412-origen.dts
> @@ -122,9 +122,9 @@
> broken-cd;
> fifo-depth = <0x80>;
> card-detect-delay = <200>;
> - samsung,dw-mshc-ciu-div = <3>;
> - samsung,dw-mshc-sdr-timing = <2 3>;
> - samsung,dw-mshc-ddr-timing = <1 2>;
> + dw-mshc-ciu-div = <3>;
> + dw-mshc-sdr-timing = <2 3>;
> + dw-mshc-ddr-timing = <1 2>;
>
> slot@0 {
> reg = <0>;
> diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts
> index abc7272..72aa743 100644
> --- a/arch/arm/boot/dts/exynos5250-arndale.dts
> +++ b/arch/arm/boot/dts/exynos5250-arndale.dts
> @@ -324,9 +324,9 @@
> broken-cd;
> fifo-depth = <0x80>;
> card-detect-delay = <200>;
> - samsung,dw-mshc-ciu-div = <3>;
> - samsung,dw-mshc-sdr-timing = <2 3>;
> - samsung,dw-mshc-ddr-timing = <1 2>;
> + dw-mshc-ciu-div = <3>;
> + dw-mshc-sdr-timing = <2 3>;
> + dw-mshc-ddr-timing = <1 2>;
> vmmc-supply = <&mmc_reg>;
> pinctrl-names = "default";
> pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>;
> @@ -346,9 +346,9 @@
> supports-highspeed;
> fifo-depth = <0x80>;
> card-detect-delay = <200>;
> - samsung,dw-mshc-ciu-div = <3>;
> - samsung,dw-mshc-sdr-timing = <2 3>;
> - samsung,dw-mshc-ddr-timing = <1 2>;
> + dw-mshc-ciu-div = <3>;
> + dw-mshc-sdr-timing = <2 3>;
> + dw-mshc-ddr-timing = <1 2>;
> vmmc-supply = <&mmc_reg>;
> pinctrl-names = "default";
> pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
> diff --git a/arch/arm/boot/dts/exynos5250-smdk5250.dts b/arch/arm/boot/dts/exynos5250-smdk5250.dts
> index 49f18c2..220da19 100644
> --- a/arch/arm/boot/dts/exynos5250-smdk5250.dts
> +++ b/arch/arm/boot/dts/exynos5250-smdk5250.dts
> @@ -146,9 +146,9 @@
> broken-cd;
> fifo-depth = <0x80>;
> card-detect-delay = <200>;
> - samsung,dw-mshc-ciu-div = <3>;
> - samsung,dw-mshc-sdr-timing = <2 3>;
> - samsung,dw-mshc-ddr-timing = <1 2>;
> + dw-mshc-ciu-div = <3>;
> + dw-mshc-sdr-timing = <2 3>;
> + dw-mshc-ddr-timing = <1 2>;
> pinctrl-names = "default";
> pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>;
>
> @@ -167,9 +167,9 @@
> supports-highspeed;
> fifo-depth = <0x80>;
> card-detect-delay = <200>;
> - samsung,dw-mshc-ciu-div = <3>;
> - samsung,dw-mshc-sdr-timing = <2 3>;
> - samsung,dw-mshc-ddr-timing = <1 2>;
> + dw-mshc-ciu-div = <3>;
> + dw-mshc-sdr-timing = <2 3>;
> + dw-mshc-ddr-timing = <1 2>;
> pinctrl-names = "default";
> pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
>
> diff --git a/drivers/mmc/host/dw_mmc-exynos.c b/drivers/mmc/host/dw_mmc-exynos.c
> index 866edef..553f3c1 100644
> --- a/drivers/mmc/host/dw_mmc-exynos.c
> +++ b/drivers/mmc/host/dw_mmc-exynos.c
> @@ -131,18 +131,18 @@ static int dw_mci_exynos_parse_dt(struct dw_mci *host)
> u32 div = 0;
> int ret;
>
> - of_property_read_u32(np, "samsung,dw-mshc-ciu-div", &div);
> + of_property_read_u32(np, "dw-mshc-ciu-div", &div);
> priv->ciu_div = div;
>
> ret = of_property_read_u32_array(np,
> - "samsung,dw-mshc-sdr-timing", timing, 2);
> + "dw-mshc-sdr-timing", timing, 2);
> if (ret)
> return ret;
>
> priv->sdr_timing = SDMMC_CLKSEL_TIMING(timing[0], timing[1], div);
>
> ret = of_property_read_u32_array(np,
> - "samsung,dw-mshc-ddr-timing", timing, 2);
> + "dw-mshc-ddr-timing", timing, 2);
> if (ret)
> return ret;
Then we can move functions related with clksel from dw-mmc-exynos.c to dw-mmc.c, isn't it?
Best Regards,
Jaehoon Chung
>
>
next prev parent reply other threads:[~2013-08-09 2:53 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-08-08 22:55 [PATCH] mmc: dw_mmc-exynos: Common bindings for dw-mshc timing dinguyen
2013-08-09 2:54 ` Jaehoon Chung [this message]
2013-08-09 12:36 ` Seungwon Jeon
2013-08-09 14:54 ` Dinh Nguyen
2013-08-12 10:36 ` Seungwon Jeon
2013-08-09 14:49 ` Dinh Nguyen
2013-08-12 23:15 ` Stephen Warren
2013-08-14 5:29 ` Olof Johansson
2013-08-14 16:09 ` Stephen Warren
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=520459C9.8020305@samsung.com \
--to=jh80.chung@samsung.com \
--cc=arnd@arndb.de \
--cc=devicetree@vger.kernel.org \
--cc=dinguyen@altera.com \
--cc=dinh.linux@gmail.com \
--cc=ian.campbell@citrix.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-mmc@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=olof@lixom.net \
--cc=pawel.moll@arm.com \
--cc=rob.herring@calxeda.com \
--cc=swarren@wwwdotorg.org \
--cc=tgih.jun@samsung.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).