From: Balaji T K <balajitk@ti.com>
To: Andreas Fenkart <afenkart@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>, Chris Ball <chris@printf.net>,
Grant Likely <grant.likely@secretlab.ca>,
Felipe Balbi <balbi@ti.com>,
Andreas Mueller <schnitzeltony@googlemail.com>,
zonque@gmail.com, galak@codeaurora.org,
linux-doc@vger.kernel.org, linux-mmc@vger.kernel.org,
linux-omap@vger.kernel.org
Subject: Re: [PATCH v11 6/7] mmc: omap_hsmmc: switch default/idle pinctrl states in runtime hooks
Date: Fri, 9 May 2014 22:41:52 +0530 [thread overview]
Message-ID: <536D0C58.8080408@ti.com> (raw)
In-Reply-To: <1399591234-13089-6-git-send-email-afenkart@gmail.com>
On Friday 09 May 2014 04:50 AM, Andreas Fenkart wrote:
> These are predefined states of the driver model. When not present,
> as if not set in the device tree, they become no-ops.
> Explicitly selecting the default state is not needed since the
> device core layer sets pin mux to "default" state before probe.
> This is not the simplest implementation, on AM335x at least, we could
> switch to idle at any point in the suspend hook, only the default state
> needs to be set before writing to the irq registers or an IRQ might get
> lost.
>
> Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
>
> diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c
> index 47a5982..5a321f98 100644
> --- a/drivers/mmc/host/omap_hsmmc.c
> +++ b/drivers/mmc/host/omap_hsmmc.c
> @@ -2032,7 +2032,6 @@ static int omap_hsmmc_probe(struct platform_device *pdev)
> const struct of_device_id *match;
> dma_cap_mask_t mask;
> unsigned tx_req, rx_req;
> - struct pinctrl *pinctrl;
> const struct omap_mmc_of_data *data;
>
> apply_clk_hack(&pdev->dev);
Looks like this patches is not based on mmc-next[1]
Can you please rebase to mmc-next
[1] http://git.kernel.org/cgit/linux/kernel/git/cjb/mmc.git/log/?id=refs/heads/mmc-next
Other than that:
Acked-by: Balaji T K <balajitk@ti.com>
> @@ -2258,11 +2257,6 @@ static int omap_hsmmc_probe(struct platform_device *pdev)
>
> omap_hsmmc_disable_irq(host);
>
> - pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
> - if (IS_ERR(pinctrl))
> - dev_warn(&pdev->dev,
> - "pins are not configured from the driver\n");
> -
> /*
> * For now, only support SDIO interrupt if we have a separate
> * wake-up interrupt configured from device tree. This is because
> @@ -2486,10 +2480,15 @@ static int omap_hsmmc_runtime_suspend(struct device *dev)
> goto abort;
> }
>
> + pinctrl_pm_select_idle_state(dev);
> +
> WARN_ON(host->flags & HSMMC_WAKE_IRQ_ENABLED);
> enable_irq(host->wake_irq);
> host->flags |= HSMMC_WAKE_IRQ_ENABLED;
> + } else {
> + pinctrl_pm_select_idle_state(dev);
> }
> +
> abort:
> spin_unlock_irqrestore(&host->irq_lock, flags);
> return ret;
> @@ -2513,9 +2512,14 @@ static int omap_hsmmc_runtime_resume(struct device *dev)
> host->flags &= ~HSMMC_WAKE_IRQ_ENABLED;
> }
>
> + pinctrl_pm_select_default_state(host->dev);
> +
> + /* irq lost, if pinmux incorrect */
> OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR);
> OMAP_HSMMC_WRITE(host->base, ISE, CIRQ_EN);
> OMAP_HSMMC_WRITE(host->base, IE, CIRQ_EN);
> + } else {
> + pinctrl_pm_select_default_state(host->dev);
> }
> spin_unlock_irqrestore(&host->irq_lock, flags);
> return 0;
>
next prev parent reply other threads:[~2014-05-09 17:12 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-05-08 23:16 [PATCH v11 0/7] mmc: omap_hsmmc: Enable SDIO IRQ Andreas Fenkart
2014-05-08 23:20 ` [PATCH v11 1/7] mmc: omap_hsmmc: compile fix for !CONFIG_OF build Andreas Fenkart
2014-05-08 23:20 ` [PATCH v11 2/7] mmc: omap_hsmmc: Enable SDIO interrupt Andreas Fenkart
2014-05-09 17:09 ` Balaji T K
2014-05-08 23:20 ` [PATCH v11 3/7] mmc: omap_hsmmc: enable wakeup event for sdio OMAP4 Andreas Fenkart
2014-05-08 23:20 ` [PATCH v11 4/7] mmc: omap_hsmmc: Extend debugfs by SDIO IRQ handling, runtime state Andreas Fenkart
2014-05-09 17:10 ` Balaji T K
2014-05-08 23:20 ` [PATCH v11 5/7] mmc: omap_hsmmc: abort runtime suspend if pending sdio irq detected Andreas Fenkart
2014-05-09 17:10 ` Balaji T K
2014-05-08 23:20 ` [PATCH v11 6/7] mmc: omap_hsmmc: switch default/idle pinctrl states in runtime hooks Andreas Fenkart
2014-05-09 17:11 ` Balaji T K [this message]
2014-05-08 23:20 ` [PATCH v11 7/7] mmc: omap_hsmmc: Pin remux workaround to support SDIO interrupt on AM335x Andreas Fenkart
2014-05-09 17:11 ` Balaji T K
2014-05-08 23:48 ` [PATCH v11 1/7] mmc: omap_hsmmc: compile fix for !CONFIG_OF build Sebastian Reichel
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=536D0C58.8080408@ti.com \
--to=balajitk@ti.com \
--cc=afenkart@gmail.com \
--cc=balbi@ti.com \
--cc=chris@printf.net \
--cc=galak@codeaurora.org \
--cc=grant.likely@secretlab.ca \
--cc=linux-doc@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=schnitzeltony@googlemail.com \
--cc=tony@atomide.com \
--cc=zonque@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).