From mboxrd@z Thu Jan 1 00:00:00 1970 From: Jaehoon Chung Subject: Re: [PATCH] mmc:core: fix hs400 timing selection Date: Tue, 28 Oct 2014 13:38:11 +0900 Message-ID: <544F1DB3.9050204@samsung.com> References: <1413946555-1266-1-git-send-email-chanho.min@lge.com> Mime-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 7bit Return-path: In-reply-to: <1413946555-1266-1-git-send-email-chanho.min@lge.com> Sender: linux-kernel-owner@vger.kernel.org To: Chanho Min , Chris Ball , Ulf Hansson , Seungwon Jeon , Jaehoon Chung Cc: linux-mmc@vger.kernel.org, linux-kernel@vger.kernel.org, HyoJun Im , gunho.lee@lge.com, Hankyung Yu , CPGS List-Id: linux-mmc@vger.kernel.org Hi, Chanho. On 10/22/2014 11:55 AM, Chanho Min wrote: > According to JEDEC v5.01 spec (6.6.5), In order to switch to HS400 mode, > host should perform the following steps. > > 1. HS200 mode selection completed > 2. Set HS_TIMING to 0x01(High Speed) > 3. Host changes frequency to =< 52MHz > 4. Set the bus width to DDR 8bit (CMD6) > 5. Host may read Driver Strength (CMD8) > 6. Set HS_TIMING to 0x03 (HS400) > > In current implementation, the order of 2 and 3 is reversed. > The HS_TIMING field should be set to 0x1 before the clock frequency > is set to a value not greater than 52 MHz. Otherwise, Initialization of > timing can be failed. Also, the host contoller's UHS timing mode should > be set to DDR50 after the bus width is set to DDR 8bit. > > Signed-off-by: Hankyung Yu > Signed-off-by: Chanho Min > --- > drivers/mmc/core/mmc.c | 13 ++++++++++--- > 1 file changed, 10 insertions(+), 3 deletions(-) > > diff --git a/drivers/mmc/core/mmc.c b/drivers/mmc/core/mmc.c > index a301a78..52f78e0 100644 > --- a/drivers/mmc/core/mmc.c > +++ b/drivers/mmc/core/mmc.c > @@ -1061,9 +1061,6 @@ static int mmc_select_hs400(struct mmc_card *card) > * Before switching to dual data rate operation for HS400, > * it is required to convert from HS200 mode to HS mode. > */ > - mmc_set_timing(card->host, MMC_TIMING_MMC_HS); > - mmc_set_bus_speed(card); > - > err = __mmc_switch(card, EXT_CSD_CMD_SET_NORMAL, > EXT_CSD_HS_TIMING, EXT_CSD_TIMING_HS, > card->ext_csd.generic_cmd6_time, > @@ -1074,6 +1071,14 @@ static int mmc_select_hs400(struct mmc_card *card) > return err; > } > > + /* > + * According to JEDEC v5.01 spec (6.6.5), Clock frequency should > + * be set to a value not greater than 52MHz after the HS_TIMING > + * field is set to 0x1. > + */ > + mmc_set_timing(card->host, MMC_TIMING_MMC_HS); > + mmc_set_bus_speed(card); > + > err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL, > EXT_CSD_BUS_WIDTH, > EXT_CSD_DDR_BUS_WIDTH_8, > @@ -1084,6 +1089,8 @@ static int mmc_select_hs400(struct mmc_card *card) > return err; > } > > + mmc_set_timing(card->host, MMC_TIMING_MMC_DDR52); > + I didn't know why timing is set to ddr50. Best Regards, Jaehoon Chung > err = __mmc_switch(card, EXT_CSD_CMD_SET_NORMAL, > EXT_CSD_HS_TIMING, EXT_CSD_TIMING_HS400, > card->ext_csd.generic_cmd6_time, >