[PATCH 2/4] MMC: Ingenic: Add 8bit mode support.

linux-mmc.vger.kernel.org archive mirror
 help / color / mirror / Atom feed

* [PATCH 2/4] MMC: Ingenic: Add 8bit mode support.
       [not found] <1567669089-88693-1-git-send-email-zhouyanjie@zoho.com>
@ 2019-09-05  7:38 ` Zhou Yanjie
  2019-09-05  7:38 ` [PATCH 3/4] dt-bindings: MMC: Add JZ4760 bindings Zhou Yanjie
                   ` (3 subsequent siblings)
  4 siblings, 0 replies; 21+ messages in thread
From: Zhou Yanjie @ 2019-09-05  7:38 UTC (permalink / raw)
  To: linux-mips
  Cc: linux-kernel, linux-mmc, devicetree, ulf.hansson, paul.burton,
	linus.walleij, paul, malat, yuehaibing, ezequiel, robh+dt,
	mark.rutland, syq, jiaxun.yang

Add support for 8bit mode, now supports 1bit/4bit/8bit modes.

Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
---
 drivers/mmc/host/jz4740_mmc.c | 12 ++++++++++--
 1 file changed, 10 insertions(+), 2 deletions(-)

diff --git a/drivers/mmc/host/jz4740_mmc.c b/drivers/mmc/host/jz4740_mmc.c
index 1b1fcb7..d6811a7 100644
--- a/drivers/mmc/host/jz4740_mmc.c
+++ b/drivers/mmc/host/jz4740_mmc.c
@@ -79,6 +79,8 @@
 
 #define JZ_MMC_CMDAT_IO_ABORT BIT(11)
 #define JZ_MMC_CMDAT_BUS_WIDTH_4BIT BIT(10)
+#define JZ_MMC_CMDAT_BUS_WIDTH_8BIT (BIT(10) | BIT(9))
+#define	JZ_MMC_CMDAT_BUS_WIDTH_MASK (BIT(10) | BIT(9))
 #define JZ_MMC_CMDAT_DMA_EN BIT(8)
 #define JZ_MMC_CMDAT_INIT BIT(7)
 #define JZ_MMC_CMDAT_BUSY BIT(6)
@@ -899,11 +901,16 @@ static void jz4740_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 
 	switch (ios->bus_width) {
 	case MMC_BUS_WIDTH_1:
-		host->cmdat &= ~JZ_MMC_CMDAT_BUS_WIDTH_4BIT;
+		host->cmdat &= ~JZ_MMC_CMDAT_BUS_WIDTH_MASK;
 		break;
 	case MMC_BUS_WIDTH_4:
+		host->cmdat &= ~JZ_MMC_CMDAT_BUS_WIDTH_MASK;
 		host->cmdat |= JZ_MMC_CMDAT_BUS_WIDTH_4BIT;
 		break;
+	case MMC_BUS_WIDTH_8:
+		host->cmdat &= ~JZ_MMC_CMDAT_BUS_WIDTH_MASK;
+		host->cmdat |= JZ_MMC_CMDAT_BUS_WIDTH_8BIT;
+		break;
 	default:
 		break;
 	}
@@ -1034,7 +1041,8 @@ static int jz4740_mmc_probe(struct platform_device* pdev)
 
 	dev_info(&pdev->dev, "Using %s, %d-bit mode\n",
 		 host->use_dma ? "DMA" : "PIO",
-		 (mmc->caps & MMC_CAP_4_BIT_DATA) ? 4 : 1);
+		 (mmc->caps & MMC_CAP_8_BIT_DATA) ? 8 :
+		 ((mmc->caps & MMC_CAP_4_BIT_DATA) ? 4 : 1));
 
 	return 0;
 
-- 
2.7.4

^ permalink raw reply related	[flat|nested] 21+ messages in thread

* [PATCH 3/4] dt-bindings: MMC: Add JZ4760 bindings.
       [not found] <1567669089-88693-1-git-send-email-zhouyanjie@zoho.com>
  2019-09-05  7:38 ` [PATCH 2/4] MMC: Ingenic: Add 8bit mode support Zhou Yanjie
@ 2019-09-05  7:38 ` Zhou Yanjie
  2019-09-13 14:36   ` Rob Herring
  2019-09-05  7:38 ` [PATCH 4/4] MMC: Ingenic: Add support for JZ4760 and support for LPM Zhou Yanjie
                   ` (2 subsequent siblings)
  4 siblings, 1 reply; 21+ messages in thread
From: Zhou Yanjie @ 2019-09-05  7:38 UTC (permalink / raw)
  To: linux-mips
  Cc: linux-kernel, linux-mmc, devicetree, ulf.hansson, paul.burton,
	linus.walleij, paul, malat, yuehaibing, ezequiel, robh+dt,
	mark.rutland, syq, jiaxun.yang

Add the MMC bindings for the JZ4760 Soc from Ingenic.

Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
---
 Documentation/devicetree/bindings/mmc/jz4740.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/mmc/jz4740.txt b/Documentation/devicetree/bindings/mmc/jz4740.txt
index 8a6f87f..13796fe 100644
--- a/Documentation/devicetree/bindings/mmc/jz4740.txt
+++ b/Documentation/devicetree/bindings/mmc/jz4740.txt
@@ -8,6 +8,7 @@ Required properties:
 - compatible: Should be one of the following:
   - "ingenic,jz4740-mmc" for the JZ4740
   - "ingenic,jz4725b-mmc" for the JZ4725B
+  - "ingenic,jz4760-mmc" for the JZ4760
   - "ingenic,jz4780-mmc" for the JZ4780
 - reg: Should contain the MMC controller registers location and length.
 - interrupts: Should contain the interrupt specifier of the MMC controller.
-- 
2.7.4

^ permalink raw reply related	[flat|nested] 21+ messages in thread

* Re: [PATCH 3/4] dt-bindings: MMC: Add JZ4760 bindings.
  2019-09-05  7:38 ` [PATCH 3/4] dt-bindings: MMC: Add JZ4760 bindings Zhou Yanjie
@ 2019-09-13 14:36   ` Rob Herring
  0 siblings, 0 replies; 21+ messages in thread
From: Rob Herring @ 2019-09-13 14:36 UTC (permalink / raw)
  To: Zhou Yanjie
  Cc: linux-mips, linux-kernel, linux-mmc, devicetree, ulf.hansson,
	paul.burton, linus.walleij, paul, malat, yuehaibing, ezequiel,
	robh+dt, mark.rutland, syq, jiaxun.yang

On Thu,  5 Sep 2019 15:38:08 +0800, Zhou Yanjie wrote:
> Add the MMC bindings for the JZ4760 Soc from Ingenic.
> 
> Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
> ---
>  Documentation/devicetree/bindings/mmc/jz4740.txt | 1 +
>  1 file changed, 1 insertion(+)
> 

Acked-by: Rob Herring <robh@kernel.org>

^ permalink raw reply	[flat|nested] 21+ messages in thread

* [PATCH 4/4] MMC: Ingenic: Add support for JZ4760 and support for LPM.
       [not found] <1567669089-88693-1-git-send-email-zhouyanjie@zoho.com>
  2019-09-05  7:38 ` [PATCH 2/4] MMC: Ingenic: Add 8bit mode support Zhou Yanjie
  2019-09-05  7:38 ` [PATCH 3/4] dt-bindings: MMC: Add JZ4760 bindings Zhou Yanjie
@ 2019-09-05  7:38 ` Zhou Yanjie
  2019-10-03 10:00   ` Ulf Hansson
       [not found] ` <1567669089-88693-2-git-send-email-zhouyanjie@zoho.com>
  2019-10-12  5:13 ` MMC: JZ4740: Add support for 8bit mode and LPM and JZ4760 Soc v2 Zhou Yanjie
  4 siblings, 1 reply; 21+ messages in thread
From: Zhou Yanjie @ 2019-09-05  7:38 UTC (permalink / raw)
  To: linux-mips
  Cc: linux-kernel, linux-mmc, devicetree, ulf.hansson, paul.burton,
	linus.walleij, paul, malat, yuehaibing, ezequiel, robh+dt,
	mark.rutland, syq, jiaxun.yang

1.add support for probing mmc driver on the JZ4760 Soc from Ingenic.
2.add support for Low Power Mode of Ingenic's MMC/SD Controller.

Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
---
 drivers/mmc/host/jz4740_mmc.c | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/drivers/mmc/host/jz4740_mmc.c b/drivers/mmc/host/jz4740_mmc.c
index d6811a7..1e61f1b 100644
--- a/drivers/mmc/host/jz4740_mmc.c
+++ b/drivers/mmc/host/jz4740_mmc.c
@@ -43,6 +43,7 @@
 #define JZ_REG_MMC_RES		0x34
 #define JZ_REG_MMC_RXFIFO	0x38
 #define JZ_REG_MMC_TXFIFO	0x3C
+#define JZ_REG_MMC_LPM		0x40
 #define JZ_REG_MMC_DMAC		0x44
 
 #define JZ_MMC_STRPCL_EXIT_MULTIPLE BIT(7)
@@ -102,11 +103,15 @@
 #define JZ_MMC_DMAC_DMA_SEL BIT(1)
 #define JZ_MMC_DMAC_DMA_EN BIT(0)
 
+#define	JZ_MMC_LPM_DRV_RISING BIT(31)
+#define	JZ_MMC_LPM_LOW_POWER_MODE_EN BIT(0)
+
 #define JZ_MMC_CLK_RATE 24000000
 
 enum jz4740_mmc_version {
 	JZ_MMC_JZ4740,
 	JZ_MMC_JZ4725B,
+	JZ_MMC_JZ4760,
 	JZ_MMC_JZ4780,
 };
 
@@ -858,6 +863,16 @@ static int jz4740_mmc_set_clock_rate(struct jz4740_mmc_host *host, int rate)
 	}
 
 	writew(div, host->base + JZ_REG_MMC_CLKRT);
+
+	if (host->version >= JZ_MMC_JZ4760) {
+		if (real_rate > 25000000)
+			writel(JZ_MMC_LPM_DRV_RISING |
+				   JZ_MMC_LPM_LOW_POWER_MODE_EN,
+				   host->base + JZ_REG_MMC_LPM);
+	} else if (host->version >= JZ_MMC_JZ4725B)
+		writel(JZ_MMC_LPM_LOW_POWER_MODE_EN,
+			   host->base + JZ_REG_MMC_LPM);
+
 	return real_rate;
 }
 
@@ -935,6 +950,7 @@ static const struct mmc_host_ops jz4740_mmc_ops = {
 static const struct of_device_id jz4740_mmc_of_match[] = {
 	{ .compatible = "ingenic,jz4740-mmc", .data = (void *) JZ_MMC_JZ4740 },
 	{ .compatible = "ingenic,jz4725b-mmc", .data = (void *)JZ_MMC_JZ4725B },
+	{ .compatible = "ingenic,jz4760-mmc", .data = (void *) JZ_MMC_JZ4760 },
 	{ .compatible = "ingenic,jz4780-mmc", .data = (void *) JZ_MMC_JZ4780 },
 	{},
 };
-- 
2.7.4

^ permalink raw reply related	[flat|nested] 21+ messages in thread

* Re: [PATCH 4/4] MMC: Ingenic: Add support for JZ4760 and support for LPM.
  2019-09-05  7:38 ` [PATCH 4/4] MMC: Ingenic: Add support for JZ4760 and support for LPM Zhou Yanjie
@ 2019-10-03 10:00   ` Ulf Hansson
  2019-10-06  5:58     ` Zhou Yanjie
  0 siblings, 1 reply; 21+ messages in thread
From: Ulf Hansson @ 2019-10-03 10:00 UTC (permalink / raw)
  To: Zhou Yanjie
  Cc: linux-mips, Linux Kernel Mailing List, linux-mmc@vger.kernel.org,
	DTML, Paul Burton, Linus Walleij, Paul Cercueil,
	Mathieu Malaterre, YueHaibing, Ezequiel Garcia, Rob Herring,
	Mark Rutland, syq, jiaxun.yang

On Thu, 5 Sep 2019 at 09:40, Zhou Yanjie <zhouyanjie@zoho.com> wrote:
>
> 1.add support for probing mmc driver on the JZ4760 Soc from Ingenic.
> 2.add support for Low Power Mode of Ingenic's MMC/SD Controller.

Normally we try to make "one" change per patch, unless there are some
good reasons not to.

In this case, it seems like you should rather split this patch into
two separate pieces. Can you please do that?

Additionally, please change the prefix for the commit message header
to start with "mmc: jz4740:"

[...]

Kind regards
Uffe

^ permalink raw reply	[flat|nested] 21+ messages in thread

* Re: [PATCH 4/4] MMC: Ingenic: Add support for JZ4760 and support for LPM.
  2019-10-03 10:00   ` Ulf Hansson
@ 2019-10-06  5:58     ` Zhou Yanjie
  0 siblings, 0 replies; 21+ messages in thread
From: Zhou Yanjie @ 2019-10-06  5:58 UTC (permalink / raw)
  To: Ulf Hansson
  Cc: linux-mips, Linux Kernel Mailing List, linux-mmc@vger.kernel.org,
	DTML, Paul Burton, Linus Walleij, Paul Cercueil,
	Mathieu Malaterre, YueHaibing, Ezequiel Garcia, Rob Herring,
	Mark Rutland, syq, jiaxun.yang

Hi Uffe,
On 2019年10月03日 18:00, Ulf Hansson wrote:
> On Thu, 5 Sep 2019 at 09:40, Zhou Yanjie <zhouyanjie@zoho.com> wrote:
>> 1.add support for probing mmc driver on the JZ4760 Soc from Ingenic.
>> 2.add support for Low Power Mode of Ingenic's MMC/SD Controller.
> Normally we try to make "one" change per patch, unless there are some
> good reasons not to.
>
> In this case, it seems like you should rather split this patch into
> two separate pieces. Can you please do that?

OK,I'll split it in v2.

>
> Additionally, please change the prefix for the commit message header
> to start with "mmc: jz4740:"

sure, it will be change in v2.

>
> [...]
>
> Kind regards
> Uffe
Thanks  and best regards!

^ permalink raw reply	[flat|nested] 21+ messages in thread

[parent not found: <1567669089-88693-2-git-send-email-zhouyanjie@zoho.com>]

* Re: [PATCH 1/4] MMC: Ingenic: Adjust the macro definition name.
       [not found] ` <1567669089-88693-2-git-send-email-zhouyanjie@zoho.com>
@ 2019-09-13 15:32   ` Ezequiel Garcia
  2019-09-13 15:59     ` Zhou Yanjie
  0 siblings, 1 reply; 21+ messages in thread
From: Ezequiel Garcia @ 2019-09-13 15:32 UTC (permalink / raw)
  To: Zhou Yanjie, linux-mips
  Cc: linux-kernel, linux-mmc, devicetree, ulf.hansson, paul.burton,
	linus.walleij, paul, malat, yuehaibing, robh+dt, mark.rutland,
	syq, jiaxun.yang

Hi Zhou,

Thanks for your interest in this driver, I'm glad
so see it's more used.

On Thu, 2019-09-05 at 15:38 +0800, Zhou Yanjie wrote:
> Adjust the macro definition name to match the corresponding
> register name in the datasheet.
> 

It's not really an issue to have slighlt different
names on the macros. They are currently sufficiently
descriptive, and I don't think it's deserves a patch.

Thanks,
Ezequiel

> Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
> ---
>  drivers/mmc/host/jz4740_mmc.c | 18 +++++++++---------
>  1 file changed, 9 insertions(+), 9 deletions(-)
> 
> diff --git a/drivers/mmc/host/jz4740_mmc.c b/drivers/mmc/host/jz4740_mmc.c
> index ffdbfaa..1b1fcb7 100644
> --- a/drivers/mmc/host/jz4740_mmc.c
> +++ b/drivers/mmc/host/jz4740_mmc.c
> @@ -28,7 +28,7 @@
>  #include <asm/mach-jz4740/dma.h>
>  
>  #define JZ_REG_MMC_STRPCL	0x00
> -#define JZ_REG_MMC_STATUS	0x04
> +#define JZ_REG_MMC_STAT		0x04
>  #define JZ_REG_MMC_CLKRT	0x08
>  #define JZ_REG_MMC_CMDAT	0x0C
>  #define JZ_REG_MMC_RESTO	0x10
> @@ -40,7 +40,7 @@
>  #define JZ_REG_MMC_IREG		0x28
>  #define JZ_REG_MMC_CMD		0x2C
>  #define JZ_REG_MMC_ARG		0x30
> -#define JZ_REG_MMC_RESP_FIFO	0x34
> +#define JZ_REG_MMC_RES		0x34
>  #define JZ_REG_MMC_RXFIFO	0x38
>  #define JZ_REG_MMC_TXFIFO	0x3C
>  #define JZ_REG_MMC_DMAC		0x44
> @@ -391,7 +391,7 @@ static void jz4740_mmc_clock_disable(struct jz4740_mmc_host *host)
>  
>  	writew(JZ_MMC_STRPCL_CLOCK_STOP, host->base + JZ_REG_MMC_STRPCL);
>  	do {
> -		status = readl(host->base + JZ_REG_MMC_STATUS);
> +		status = readl(host->base + JZ_REG_MMC_STAT);
>  	} while (status & JZ_MMC_STATUS_CLK_EN && --timeout);
>  }
>  
> @@ -403,7 +403,7 @@ static void jz4740_mmc_reset(struct jz4740_mmc_host *host)
>  	writew(JZ_MMC_STRPCL_RESET, host->base + JZ_REG_MMC_STRPCL);
>  	udelay(10);
>  	do {
> -		status = readl(host->base + JZ_REG_MMC_STATUS);
> +		status = readl(host->base + JZ_REG_MMC_STAT);
>  	} while (status & JZ_MMC_STATUS_IS_RESETTING && --timeout);
>  }
>  
> @@ -446,7 +446,7 @@ static void jz4740_mmc_transfer_check_state(struct jz4740_mmc_host *host,
>  {
>  	int status;
>  
> -	status = readl(host->base + JZ_REG_MMC_STATUS);
> +	status = readl(host->base + JZ_REG_MMC_STAT);
>  	if (status & JZ_MMC_STATUS_WRITE_ERROR_MASK) {
>  		if (status & (JZ_MMC_STATUS_TIMEOUT_WRITE)) {
>  			host->req->cmd->error = -ETIMEDOUT;
> @@ -580,10 +580,10 @@ static bool jz4740_mmc_read_data(struct jz4740_mmc_host *host,
>  	/* For whatever reason there is sometime one word more in the fifo then
>  	 * requested */
>  	timeout = 1000;
> -	status = readl(host->base + JZ_REG_MMC_STATUS);
> +	status = readl(host->base + JZ_REG_MMC_STAT);
>  	while (!(status & JZ_MMC_STATUS_DATA_FIFO_EMPTY) && --timeout) {
>  		d = readl(fifo_addr);
> -		status = readl(host->base + JZ_REG_MMC_STATUS);
> +		status = readl(host->base + JZ_REG_MMC_STAT);
>  	}
>  
>  	return false;
> @@ -614,7 +614,7 @@ static void jz4740_mmc_read_response(struct jz4740_mmc_host *host,
>  {
>  	int i;
>  	uint16_t tmp;
> -	void __iomem *fifo_addr = host->base + JZ_REG_MMC_RESP_FIFO;
> +	void __iomem *fifo_addr = host->base + JZ_REG_MMC_RES;
>  
>  	if (cmd->flags & MMC_RSP_136) {
>  		tmp = readw(fifo_addr);
> @@ -797,7 +797,7 @@ static irqreturn_t jz_mmc_irq(int irq, void *devid)
>  	struct mmc_command *cmd = host->cmd;
>  	uint32_t irq_reg, status, tmp;
>  
> -	status = readl(host->base + JZ_REG_MMC_STATUS);
> +	status = readl(host->base + JZ_REG_MMC_STAT);
>  	irq_reg = jz4740_mmc_read_irq_reg(host);
>  
>  	tmp = irq_reg;

^ permalink raw reply	[flat|nested] 21+ messages in thread

* Re: [PATCH 1/4] MMC: Ingenic: Adjust the macro definition name.
  2019-09-13 15:32   ` [PATCH 1/4] MMC: Ingenic: Adjust the macro definition name Ezequiel Garcia
@ 2019-09-13 15:59     ` Zhou Yanjie
  0 siblings, 0 replies; 21+ messages in thread
From: Zhou Yanjie @ 2019-09-13 15:59 UTC (permalink / raw)
  To: Ezequiel Garcia, linux-mips
  Cc: linux-kernel, linux-mmc, devicetree, ulf.hansson, paul.burton,
	linus.walleij, paul, malat, yuehaibing, robh+dt, mark.rutland,
	syq, jiaxun.yang

Hi Ezequiel,

On 2019年09月13日 23:32, Ezequiel Garcia wrote:
> Hi Zhou,
>
> Thanks for your interest in this driver, I'm glad
> so see it's more used.
>
> On Thu, 2019-09-05 at 15:38 +0800, Zhou Yanjie wrote:
>> Adjust the macro definition name to match the corresponding
>> register name in the datasheet.
>>
> It's not really an issue to have slighlt different
> names on the macros. They are currently sufficiently
> descriptive, and I don't think it's deserves a patch.
Thanks for your advice, I'll drop this in v2. Do you have any suggestions
for the other three patches?

Best regards!
>
> Thanks,
> Ezequiel
>
>> Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
>> ---
>>   drivers/mmc/host/jz4740_mmc.c | 18 +++++++++---------
>>   1 file changed, 9 insertions(+), 9 deletions(-)
>>
>> diff --git a/drivers/mmc/host/jz4740_mmc.c b/drivers/mmc/host/jz4740_mmc.c
>> index ffdbfaa..1b1fcb7 100644
>> --- a/drivers/mmc/host/jz4740_mmc.c
>> +++ b/drivers/mmc/host/jz4740_mmc.c
>> @@ -28,7 +28,7 @@
>>   #include <asm/mach-jz4740/dma.h>
>>   
>>   #define JZ_REG_MMC_STRPCL	0x00
>> -#define JZ_REG_MMC_STATUS	0x04
>> +#define JZ_REG_MMC_STAT		0x04
>>   #define JZ_REG_MMC_CLKRT	0x08
>>   #define JZ_REG_MMC_CMDAT	0x0C
>>   #define JZ_REG_MMC_RESTO	0x10
>> @@ -40,7 +40,7 @@
>>   #define JZ_REG_MMC_IREG		0x28
>>   #define JZ_REG_MMC_CMD		0x2C
>>   #define JZ_REG_MMC_ARG		0x30
>> -#define JZ_REG_MMC_RESP_FIFO	0x34
>> +#define JZ_REG_MMC_RES		0x34
>>   #define JZ_REG_MMC_RXFIFO	0x38
>>   #define JZ_REG_MMC_TXFIFO	0x3C
>>   #define JZ_REG_MMC_DMAC		0x44
>> @@ -391,7 +391,7 @@ static void jz4740_mmc_clock_disable(struct jz4740_mmc_host *host)
>>   
>>   	writew(JZ_MMC_STRPCL_CLOCK_STOP, host->base + JZ_REG_MMC_STRPCL);
>>   	do {
>> -		status = readl(host->base + JZ_REG_MMC_STATUS);
>> +		status = readl(host->base + JZ_REG_MMC_STAT);
>>   	} while (status & JZ_MMC_STATUS_CLK_EN && --timeout);
>>   }
>>   
>> @@ -403,7 +403,7 @@ static void jz4740_mmc_reset(struct jz4740_mmc_host *host)
>>   	writew(JZ_MMC_STRPCL_RESET, host->base + JZ_REG_MMC_STRPCL);
>>   	udelay(10);
>>   	do {
>> -		status = readl(host->base + JZ_REG_MMC_STATUS);
>> +		status = readl(host->base + JZ_REG_MMC_STAT);
>>   	} while (status & JZ_MMC_STATUS_IS_RESETTING && --timeout);
>>   }
>>   
>> @@ -446,7 +446,7 @@ static void jz4740_mmc_transfer_check_state(struct jz4740_mmc_host *host,
>>   {
>>   	int status;
>>   
>> -	status = readl(host->base + JZ_REG_MMC_STATUS);
>> +	status = readl(host->base + JZ_REG_MMC_STAT);
>>   	if (status & JZ_MMC_STATUS_WRITE_ERROR_MASK) {
>>   		if (status & (JZ_MMC_STATUS_TIMEOUT_WRITE)) {
>>   			host->req->cmd->error = -ETIMEDOUT;
>> @@ -580,10 +580,10 @@ static bool jz4740_mmc_read_data(struct jz4740_mmc_host *host,
>>   	/* For whatever reason there is sometime one word more in the fifo then
>>   	 * requested */
>>   	timeout = 1000;
>> -	status = readl(host->base + JZ_REG_MMC_STATUS);
>> +	status = readl(host->base + JZ_REG_MMC_STAT);
>>   	while (!(status & JZ_MMC_STATUS_DATA_FIFO_EMPTY) && --timeout) {
>>   		d = readl(fifo_addr);
>> -		status = readl(host->base + JZ_REG_MMC_STATUS);
>> +		status = readl(host->base + JZ_REG_MMC_STAT);
>>   	}
>>   
>>   	return false;
>> @@ -614,7 +614,7 @@ static void jz4740_mmc_read_response(struct jz4740_mmc_host *host,
>>   {
>>   	int i;
>>   	uint16_t tmp;
>> -	void __iomem *fifo_addr = host->base + JZ_REG_MMC_RESP_FIFO;
>> +	void __iomem *fifo_addr = host->base + JZ_REG_MMC_RES;
>>   
>>   	if (cmd->flags & MMC_RSP_136) {
>>   		tmp = readw(fifo_addr);
>> @@ -797,7 +797,7 @@ static irqreturn_t jz_mmc_irq(int irq, void *devid)
>>   	struct mmc_command *cmd = host->cmd;
>>   	uint32_t irq_reg, status, tmp;
>>   
>> -	status = readl(host->base + JZ_REG_MMC_STATUS);
>> +	status = readl(host->base + JZ_REG_MMC_STAT);
>>   	irq_reg = jz4740_mmc_read_irq_reg(host);
>>   
>>   	tmp = irq_reg;
>
>

^ permalink raw reply	[flat|nested] 21+ messages in thread

* MMC: JZ4740: Add support for 8bit mode and LPM and JZ4760 Soc v2
       [not found] <1567669089-88693-1-git-send-email-zhouyanjie@zoho.com>
                   ` (3 preceding siblings ...)
       [not found] ` <1567669089-88693-2-git-send-email-zhouyanjie@zoho.com>
@ 2019-10-12  5:13 ` Zhou Yanjie
  2019-10-12  5:13   ` [PATCH 1/6 v2] MMC: Ingenic: Add 8bit mode support Zhou Yanjie
                     ` (5 more replies)
  4 siblings, 6 replies; 21+ messages in thread
From: Zhou Yanjie @ 2019-10-12  5:13 UTC (permalink / raw)
  To: linux-mips
  Cc: linux-kernel, linux-mmc, devicetree, robh+dt, paul.burton,
	mark.rutland, syq, ulf.hansson, linus.walleij, armijn, tglx,
	yuehaibing, malat, ezequiel, paul

v1->v2: drop macro definition rename, split patch, add support for x1000.

^ permalink raw reply	[flat|nested] 21+ messages in thread

* [PATCH 1/6 v2] MMC: Ingenic: Add 8bit mode support.
  2019-10-12  5:13 ` MMC: JZ4740: Add support for 8bit mode and LPM and JZ4760 Soc v2 Zhou Yanjie
@ 2019-10-12  5:13   ` Zhou Yanjie
  2019-10-12  5:13   ` [PATCH 2/6 v2] dt-bindings: MMC: Add JZ4760 bindings Zhou Yanjie
                     ` (4 subsequent siblings)
  5 siblings, 0 replies; 21+ messages in thread
From: Zhou Yanjie @ 2019-10-12  5:13 UTC (permalink / raw)
  To: linux-mips
  Cc: linux-kernel, linux-mmc, devicetree, robh+dt, paul.burton,
	mark.rutland, syq, ulf.hansson, linus.walleij, armijn, tglx,
	yuehaibing, malat, ezequiel, paul

Add support for 8bit mode, now supports 1bit/4bit/8bit modes.

Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
---
 drivers/mmc/host/jz4740_mmc.c | 12 ++++++++++--
 1 file changed, 10 insertions(+), 2 deletions(-)

diff --git a/drivers/mmc/host/jz4740_mmc.c b/drivers/mmc/host/jz4740_mmc.c
index ffdbfaa..69c4a8b 100644
--- a/drivers/mmc/host/jz4740_mmc.c
+++ b/drivers/mmc/host/jz4740_mmc.c
@@ -79,6 +79,8 @@
 
 #define JZ_MMC_CMDAT_IO_ABORT BIT(11)
 #define JZ_MMC_CMDAT_BUS_WIDTH_4BIT BIT(10)
+#define JZ_MMC_CMDAT_BUS_WIDTH_8BIT (BIT(10) | BIT(9))
+#define	JZ_MMC_CMDAT_BUS_WIDTH_MASK (BIT(10) | BIT(9))
 #define JZ_MMC_CMDAT_DMA_EN BIT(8)
 #define JZ_MMC_CMDAT_INIT BIT(7)
 #define JZ_MMC_CMDAT_BUSY BIT(6)
@@ -899,11 +901,16 @@ static void jz4740_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 
 	switch (ios->bus_width) {
 	case MMC_BUS_WIDTH_1:
-		host->cmdat &= ~JZ_MMC_CMDAT_BUS_WIDTH_4BIT;
+		host->cmdat &= ~JZ_MMC_CMDAT_BUS_WIDTH_MASK;
 		break;
 	case MMC_BUS_WIDTH_4:
+		host->cmdat &= ~JZ_MMC_CMDAT_BUS_WIDTH_MASK;
 		host->cmdat |= JZ_MMC_CMDAT_BUS_WIDTH_4BIT;
 		break;
+	case MMC_BUS_WIDTH_8:
+		host->cmdat &= ~JZ_MMC_CMDAT_BUS_WIDTH_MASK;
+		host->cmdat |= JZ_MMC_CMDAT_BUS_WIDTH_8BIT;
+		break;
 	default:
 		break;
 	}
@@ -1034,7 +1041,8 @@ static int jz4740_mmc_probe(struct platform_device* pdev)
 
 	dev_info(&pdev->dev, "Using %s, %d-bit mode\n",
 		 host->use_dma ? "DMA" : "PIO",
-		 (mmc->caps & MMC_CAP_4_BIT_DATA) ? 4 : 1);
+		 (mmc->caps & MMC_CAP_8_BIT_DATA) ? 8 :
+		 ((mmc->caps & MMC_CAP_4_BIT_DATA) ? 4 : 1));
 
 	return 0;
 
-- 
2.7.4

^ permalink raw reply related	[flat|nested] 21+ messages in thread

* [PATCH 2/6 v2] dt-bindings: MMC: Add JZ4760 bindings.
  2019-10-12  5:13 ` MMC: JZ4740: Add support for 8bit mode and LPM and JZ4760 Soc v2 Zhou Yanjie
  2019-10-12  5:13   ` [PATCH 1/6 v2] MMC: Ingenic: Add 8bit mode support Zhou Yanjie
@ 2019-10-12  5:13   ` Zhou Yanjie
  2019-10-12  5:13   ` [PATCH 3/6 v2] MMC: JZ4740: Add support for the JZ4760 Zhou Yanjie
                     ` (3 subsequent siblings)
  5 siblings, 0 replies; 21+ messages in thread
From: Zhou Yanjie @ 2019-10-12  5:13 UTC (permalink / raw)
  To: linux-mips
  Cc: linux-kernel, linux-mmc, devicetree, robh+dt, paul.burton,
	mark.rutland, syq, ulf.hansson, linus.walleij, armijn, tglx,
	yuehaibing, malat, ezequiel, paul

Add the MMC bindings for the JZ4760 Soc from Ingenic.

Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
Acked-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/mmc/jz4740.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/mmc/jz4740.txt b/Documentation/devicetree/bindings/mmc/jz4740.txt
index 8a6f87f..13796fe 100644
--- a/Documentation/devicetree/bindings/mmc/jz4740.txt
+++ b/Documentation/devicetree/bindings/mmc/jz4740.txt
@@ -8,6 +8,7 @@ Required properties:
 - compatible: Should be one of the following:
   - "ingenic,jz4740-mmc" for the JZ4740
   - "ingenic,jz4725b-mmc" for the JZ4725B
+  - "ingenic,jz4760-mmc" for the JZ4760
   - "ingenic,jz4780-mmc" for the JZ4780
 - reg: Should contain the MMC controller registers location and length.
 - interrupts: Should contain the interrupt specifier of the MMC controller.
-- 
2.7.4

^ permalink raw reply related	[flat|nested] 21+ messages in thread

* [PATCH 3/6 v2] MMC: JZ4740: Add support for the JZ4760.
  2019-10-12  5:13 ` MMC: JZ4740: Add support for 8bit mode and LPM and JZ4760 Soc v2 Zhou Yanjie
  2019-10-12  5:13   ` [PATCH 1/6 v2] MMC: Ingenic: Add 8bit mode support Zhou Yanjie
  2019-10-12  5:13   ` [PATCH 2/6 v2] dt-bindings: MMC: Add JZ4760 bindings Zhou Yanjie
@ 2019-10-12  5:13   ` Zhou Yanjie
  2019-10-12  5:13   ` [PATCH 4/6 v2] dt-bindings: MMC: Add X1000 bindings Zhou Yanjie
                     ` (2 subsequent siblings)
  5 siblings, 0 replies; 21+ messages in thread
From: Zhou Yanjie @ 2019-10-12  5:13 UTC (permalink / raw)
  To: linux-mips
  Cc: linux-kernel, linux-mmc, devicetree, robh+dt, paul.burton,
	mark.rutland, syq, ulf.hansson, linus.walleij, armijn, tglx,
	yuehaibing, malat, ezequiel, paul

Add support for probing mmc driver on the JZ4760 Soc from Ingenic.

Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
---
 drivers/mmc/host/jz4740_mmc.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/mmc/host/jz4740_mmc.c b/drivers/mmc/host/jz4740_mmc.c
index 69c4a8b..f4c4890 100644
--- a/drivers/mmc/host/jz4740_mmc.c
+++ b/drivers/mmc/host/jz4740_mmc.c
@@ -107,6 +107,7 @@
 enum jz4740_mmc_version {
 	JZ_MMC_JZ4740,
 	JZ_MMC_JZ4725B,
+	JZ_MMC_JZ4760,
 	JZ_MMC_JZ4780,
 };
 
@@ -935,6 +936,7 @@ static const struct mmc_host_ops jz4740_mmc_ops = {
 static const struct of_device_id jz4740_mmc_of_match[] = {
 	{ .compatible = "ingenic,jz4740-mmc", .data = (void *) JZ_MMC_JZ4740 },
 	{ .compatible = "ingenic,jz4725b-mmc", .data = (void *)JZ_MMC_JZ4725B },
+	{ .compatible = "ingenic,jz4760-mmc", .data = (void *) JZ_MMC_JZ4760 },
 	{ .compatible = "ingenic,jz4780-mmc", .data = (void *) JZ_MMC_JZ4780 },
 	{},
 };
-- 
2.7.4

^ permalink raw reply related	[flat|nested] 21+ messages in thread

* [PATCH 4/6 v2] dt-bindings: MMC: Add X1000 bindings.
  2019-10-12  5:13 ` MMC: JZ4740: Add support for 8bit mode and LPM and JZ4760 Soc v2 Zhou Yanjie
                     ` (2 preceding siblings ...)
  2019-10-12  5:13   ` [PATCH 3/6 v2] MMC: JZ4740: Add support for the JZ4760 Zhou Yanjie
@ 2019-10-12  5:13   ` Zhou Yanjie
  2019-10-14 18:15     ` Rob Herring
  2019-10-12  5:13   ` [PATCH 5/6 v2] MMC: JZ4740: Add support for the X1000 Zhou Yanjie
  2019-10-12  5:13   ` [PATCH 6/6 v2] MMC: JZ4740: Add support for LPM Zhou Yanjie
  5 siblings, 1 reply; 21+ messages in thread
From: Zhou Yanjie @ 2019-10-12  5:13 UTC (permalink / raw)
  To: linux-mips
  Cc: linux-kernel, linux-mmc, devicetree, robh+dt, paul.burton,
	mark.rutland, syq, ulf.hansson, linus.walleij, armijn, tglx,
	yuehaibing, malat, ezequiel, paul

Add the MMC bindings for the X1000 Soc from Ingenic.

Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
---
 Documentation/devicetree/bindings/mmc/jz4740.txt | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/mmc/jz4740.txt b/Documentation/devicetree/bindings/mmc/jz4740.txt
index 13796fe..453d3b9 100644
--- a/Documentation/devicetree/bindings/mmc/jz4740.txt
+++ b/Documentation/devicetree/bindings/mmc/jz4740.txt
@@ -1,8 +1,8 @@
-* Ingenic JZ47xx MMC controllers
+* Ingenic XBurst MMC controllers
 
 This file documents the device tree properties used for the MMC controller in
-Ingenic JZ4740/JZ4780 SoCs. These are in addition to the core MMC properties
-described in mmc.txt.
+Ingenic JZ4740/JZ4760/JZ4780/X1000 SoCs. These are in addition to the core MMC
+properties described in mmc.txt.
 
 Required properties:
 - compatible: Should be one of the following:
@@ -10,6 +10,7 @@ Required properties:
   - "ingenic,jz4725b-mmc" for the JZ4725B
   - "ingenic,jz4760-mmc" for the JZ4760
   - "ingenic,jz4780-mmc" for the JZ4780
+  - "ingenic,x1000-mmc" for the X1000
 - reg: Should contain the MMC controller registers location and length.
 - interrupts: Should contain the interrupt specifier of the MMC controller.
 - clocks: Clock for the MMC controller.
-- 
2.7.4

^ permalink raw reply related	[flat|nested] 21+ messages in thread

* Re: [PATCH 4/6 v2] dt-bindings: MMC: Add X1000 bindings.
  2019-10-12  5:13   ` [PATCH 4/6 v2] dt-bindings: MMC: Add X1000 bindings Zhou Yanjie
@ 2019-10-14 18:15     ` Rob Herring
  0 siblings, 0 replies; 21+ messages in thread
From: Rob Herring @ 2019-10-14 18:15 UTC (permalink / raw)
  To: Zhou Yanjie
  Cc: linux-mips, linux-kernel, linux-mmc, devicetree, robh+dt,
	paul.burton, mark.rutland, syq, ulf.hansson, linus.walleij,
	armijn, tglx, yuehaibing, malat, ezequiel, paul

On Sat, 12 Oct 2019 13:13:18 +0800, Zhou Yanjie wrote:
> Add the MMC bindings for the X1000 Soc from Ingenic.
> 
> Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
> ---
>  Documentation/devicetree/bindings/mmc/jz4740.txt | 7 ++++---
>  1 file changed, 4 insertions(+), 3 deletions(-)
> 

Acked-by: Rob Herring <robh@kernel.org>

^ permalink raw reply	[flat|nested] 21+ messages in thread

* [PATCH 5/6 v2] MMC: JZ4740: Add support for the X1000.
  2019-10-12  5:13 ` MMC: JZ4740: Add support for 8bit mode and LPM and JZ4760 Soc v2 Zhou Yanjie
                     ` (3 preceding siblings ...)
  2019-10-12  5:13   ` [PATCH 4/6 v2] dt-bindings: MMC: Add X1000 bindings Zhou Yanjie
@ 2019-10-12  5:13   ` Zhou Yanjie
  2019-10-12  5:13   ` [PATCH 6/6 v2] MMC: JZ4740: Add support for LPM Zhou Yanjie
  5 siblings, 0 replies; 21+ messages in thread
From: Zhou Yanjie @ 2019-10-12  5:13 UTC (permalink / raw)
  To: linux-mips
  Cc: linux-kernel, linux-mmc, devicetree, robh+dt, paul.burton,
	mark.rutland, syq, ulf.hansson, linus.walleij, armijn, tglx,
	yuehaibing, malat, ezequiel, paul

Add support for probing mmc driver on the X1000 Soc from Ingenic.

Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
---
 drivers/mmc/host/jz4740_mmc.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/mmc/host/jz4740_mmc.c b/drivers/mmc/host/jz4740_mmc.c
index f4c4890..44a04fe 100644
--- a/drivers/mmc/host/jz4740_mmc.c
+++ b/drivers/mmc/host/jz4740_mmc.c
@@ -109,6 +109,7 @@ enum jz4740_mmc_version {
 	JZ_MMC_JZ4725B,
 	JZ_MMC_JZ4760,
 	JZ_MMC_JZ4780,
+	JZ_MMC_X1000,
 };
 
 enum jz4740_mmc_state {
@@ -938,6 +939,7 @@ static const struct of_device_id jz4740_mmc_of_match[] = {
 	{ .compatible = "ingenic,jz4725b-mmc", .data = (void *)JZ_MMC_JZ4725B },
 	{ .compatible = "ingenic,jz4760-mmc", .data = (void *) JZ_MMC_JZ4760 },
 	{ .compatible = "ingenic,jz4780-mmc", .data = (void *) JZ_MMC_JZ4780 },
+	{ .compatible = "ingenic,x1000-mmc", .data = (void *) JZ_MMC_X1000 },
 	{},
 };
 MODULE_DEVICE_TABLE(of, jz4740_mmc_of_match);
@@ -1039,7 +1041,7 @@ static int jz4740_mmc_probe(struct platform_device* pdev)
 		dev_err(&pdev->dev, "Failed to add mmc host: %d\n", ret);
 		goto err_release_dma;
 	}
-	dev_info(&pdev->dev, "JZ SD/MMC card driver registered\n");
+	dev_info(&pdev->dev, "Ingenic SD/MMC card driver registered\n");
 
 	dev_info(&pdev->dev, "Using %s, %d-bit mode\n",
 		 host->use_dma ? "DMA" : "PIO",
-- 
2.7.4

^ permalink raw reply related	[flat|nested] 21+ messages in thread

* [PATCH 6/6 v2] MMC: JZ4740: Add support for LPM.
  2019-10-12  5:13 ` MMC: JZ4740: Add support for 8bit mode and LPM and JZ4760 Soc v2 Zhou Yanjie
                     ` (4 preceding siblings ...)
  2019-10-12  5:13   ` [PATCH 5/6 v2] MMC: JZ4740: Add support for the X1000 Zhou Yanjie
@ 2019-10-12  5:13   ` Zhou Yanjie
  2019-10-18  8:52     ` Ulf Hansson
  5 siblings, 1 reply; 21+ messages in thread
From: Zhou Yanjie @ 2019-10-12  5:13 UTC (permalink / raw)
  To: linux-mips
  Cc: linux-kernel, linux-mmc, devicetree, robh+dt, paul.burton,
	mark.rutland, syq, ulf.hansson, linus.walleij, armijn, tglx,
	yuehaibing, malat, ezequiel, paul

add support for low power mode of Ingenic's MMC/SD Controller.

Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
---
 drivers/mmc/host/jz4740_mmc.c | 23 +++++++++++++++++++++++
 1 file changed, 23 insertions(+)

diff --git a/drivers/mmc/host/jz4740_mmc.c b/drivers/mmc/host/jz4740_mmc.c
index 44a04fe..4cbe7fb 100644
--- a/drivers/mmc/host/jz4740_mmc.c
+++ b/drivers/mmc/host/jz4740_mmc.c
@@ -43,6 +43,7 @@
 #define JZ_REG_MMC_RESP_FIFO	0x34
 #define JZ_REG_MMC_RXFIFO	0x38
 #define JZ_REG_MMC_TXFIFO	0x3C
+#define JZ_REG_MMC_LPM		0x40
 #define JZ_REG_MMC_DMAC		0x44
 
 #define JZ_MMC_STRPCL_EXIT_MULTIPLE BIT(7)
@@ -102,6 +103,12 @@
 #define JZ_MMC_DMAC_DMA_SEL BIT(1)
 #define JZ_MMC_DMAC_DMA_EN BIT(0)
 
+#define	JZ_MMC_LPM_DRV_RISING BIT(31)
+#define	JZ_MMC_LPM_DRV_RISING_QTR_PHASE_DLY BIT(31)
+#define	JZ_MMC_LPM_DRV_RISING_1NS_DLY BIT(30)
+#define	JZ_MMC_LPM_SMP_RISING_QTR_OR_HALF_PHASE_DLY BIT(29)
+#define	JZ_MMC_LPM_LOW_POWER_MODE_EN BIT(0)
+
 #define JZ_MMC_CLK_RATE 24000000
 
 enum jz4740_mmc_version {
@@ -860,6 +867,22 @@ static int jz4740_mmc_set_clock_rate(struct jz4740_mmc_host *host, int rate)
 	}
 
 	writew(div, host->base + JZ_REG_MMC_CLKRT);
+
+	if (real_rate > 25000000) {
+		if (host->version >= JZ_MMC_X1000) {
+			writel(JZ_MMC_LPM_DRV_RISING_QTR_PHASE_DLY |
+				   JZ_MMC_LPM_SMP_RISING_QTR_OR_HALF_PHASE_DLY |
+				   JZ_MMC_LPM_LOW_POWER_MODE_EN,
+				   host->base + JZ_REG_MMC_LPM);
+		} else if (host->version >= JZ_MMC_JZ4760) {
+			writel(JZ_MMC_LPM_DRV_RISING |
+				   JZ_MMC_LPM_LOW_POWER_MODE_EN,
+				   host->base + JZ_REG_MMC_LPM);
+		} else if (host->version >= JZ_MMC_JZ4725B)
+			writel(JZ_MMC_LPM_LOW_POWER_MODE_EN,
+				   host->base + JZ_REG_MMC_LPM);
+	}
+
 	return real_rate;
 }
 
-- 
2.7.4

^ permalink raw reply related	[flat|nested] 21+ messages in thread

* Re: [PATCH 6/6 v2] MMC: JZ4740: Add support for LPM.
  2019-10-12  5:13   ` [PATCH 6/6 v2] MMC: JZ4740: Add support for LPM Zhou Yanjie
@ 2019-10-18  8:52     ` Ulf Hansson
  2019-10-18 15:37       ` Paul Cercueil
  2019-10-18 16:54       ` Zhou Yanjie
  0 siblings, 2 replies; 21+ messages in thread
From: Ulf Hansson @ 2019-10-18  8:52 UTC (permalink / raw)
  To: Zhou Yanjie, Paul Cercueil
  Cc: linux-mips, Linux Kernel Mailing List, linux-mmc@vger.kernel.org,
	DTML, Rob Herring, Paul Burton, Mark Rutland, syq, Linus Walleij,
	armijn, Thomas Gleixner, YueHaibing, Mathieu Malaterre,
	Ezequiel Garcia

On Sat, 12 Oct 2019 at 07:19, Zhou Yanjie <zhouyanjie@zoho.com> wrote:
>
> add support for low power mode of Ingenic's MMC/SD Controller.
>
> Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>

I couldn't find a proper coverletter for the series, please provide
that next time as it really helps review. Additionally, it seems like
you forgot to change the prefix of the patches to "mmc: jz4740" (or at
least you chosed upper case letters), but I will take care of that
this time. So, I have applied the series for next, thanks!

I also have a general question. Should we perhaps rename the driver
from jz4740_mmc.c to ingenic.c (and the file for the DT bindings, the
Kconfig, etc), as that seems like a more appropriate name? No?

Kind regards
Uffe


> ---
>  drivers/mmc/host/jz4740_mmc.c | 23 +++++++++++++++++++++++
>  1 file changed, 23 insertions(+)
>
> diff --git a/drivers/mmc/host/jz4740_mmc.c b/drivers/mmc/host/jz4740_mmc.c
> index 44a04fe..4cbe7fb 100644
> --- a/drivers/mmc/host/jz4740_mmc.c
> +++ b/drivers/mmc/host/jz4740_mmc.c
> @@ -43,6 +43,7 @@
>  #define JZ_REG_MMC_RESP_FIFO   0x34
>  #define JZ_REG_MMC_RXFIFO      0x38
>  #define JZ_REG_MMC_TXFIFO      0x3C
> +#define JZ_REG_MMC_LPM         0x40
>  #define JZ_REG_MMC_DMAC                0x44
>
>  #define JZ_MMC_STRPCL_EXIT_MULTIPLE BIT(7)
> @@ -102,6 +103,12 @@
>  #define JZ_MMC_DMAC_DMA_SEL BIT(1)
>  #define JZ_MMC_DMAC_DMA_EN BIT(0)
>
> +#define        JZ_MMC_LPM_DRV_RISING BIT(31)
> +#define        JZ_MMC_LPM_DRV_RISING_QTR_PHASE_DLY BIT(31)
> +#define        JZ_MMC_LPM_DRV_RISING_1NS_DLY BIT(30)
> +#define        JZ_MMC_LPM_SMP_RISING_QTR_OR_HALF_PHASE_DLY BIT(29)
> +#define        JZ_MMC_LPM_LOW_POWER_MODE_EN BIT(0)
> +
>  #define JZ_MMC_CLK_RATE 24000000
>
>  enum jz4740_mmc_version {
> @@ -860,6 +867,22 @@ static int jz4740_mmc_set_clock_rate(struct jz4740_mmc_host *host, int rate)
>         }
>
>         writew(div, host->base + JZ_REG_MMC_CLKRT);
> +
> +       if (real_rate > 25000000) {
> +               if (host->version >= JZ_MMC_X1000) {
> +                       writel(JZ_MMC_LPM_DRV_RISING_QTR_PHASE_DLY |
> +                                  JZ_MMC_LPM_SMP_RISING_QTR_OR_HALF_PHASE_DLY |
> +                                  JZ_MMC_LPM_LOW_POWER_MODE_EN,
> +                                  host->base + JZ_REG_MMC_LPM);
> +               } else if (host->version >= JZ_MMC_JZ4760) {
> +                       writel(JZ_MMC_LPM_DRV_RISING |
> +                                  JZ_MMC_LPM_LOW_POWER_MODE_EN,
> +                                  host->base + JZ_REG_MMC_LPM);
> +               } else if (host->version >= JZ_MMC_JZ4725B)
> +                       writel(JZ_MMC_LPM_LOW_POWER_MODE_EN,
> +                                  host->base + JZ_REG_MMC_LPM);
> +       }
> +
>         return real_rate;
>  }
>
> --
> 2.7.4
>
>

^ permalink raw reply	[flat|nested] 21+ messages in thread

* Re: [PATCH 6/6 v2] MMC: JZ4740: Add support for LPM.
  2019-10-18  8:52     ` Ulf Hansson
@ 2019-10-18 15:37       ` Paul Cercueil
  2019-10-18 16:54       ` Zhou Yanjie
  1 sibling, 0 replies; 21+ messages in thread
From: Paul Cercueil @ 2019-10-18 15:37 UTC (permalink / raw)
  To: Ulf Hansson
  Cc: Zhou Yanjie, linux-mips, Linux Kernel Mailing List, linux-mmc,
	DTML, Rob Herring, Paul Burton, Mark Rutland, syq, Linus Walleij,
	armijn, Thomas Gleixner, YueHaibing, Mathieu Malaterre,
	Ezequiel Garcia

Hi Uffe,


Le ven., oct. 18, 2019 at 10:52, Ulf Hansson <ulf.hansson@linaro.org> a 
écrit :
> On Sat, 12 Oct 2019 at 07:19, Zhou Yanjie <zhouyanjie@zoho.com> wrote:
>> 
>>  add support for low power mode of Ingenic's MMC/SD Controller.
>> 
>>  Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
> 
> I couldn't find a proper coverletter for the series, please provide
> that next time as it really helps review. Additionally, it seems like
> you forgot to change the prefix of the patches to "mmc: jz4740" (or at
> least you chosed upper case letters), but I will take care of that
> this time. So, I have applied the series for next, thanks!
> 
> I also have a general question. Should we perhaps rename the driver
> from jz4740_mmc.c to ingenic.c (and the file for the DT bindings, the
> Kconfig, etc), as that seems like a more appropriate name? No?

Is there a kernel policy regarding renaming drivers? Since it trashes 
the git history. Anyway you're the subsystem maintainer so I guess 
that's up to you. I can send a patch to rename it if you want.

Cheers,
-Paul


> 
> Kind regards
> Uffe
> 
> 
>>  ---
>>   drivers/mmc/host/jz4740_mmc.c | 23 +++++++++++++++++++++++
>>   1 file changed, 23 insertions(+)
>> 
>>  diff --git a/drivers/mmc/host/jz4740_mmc.c 
>> b/drivers/mmc/host/jz4740_mmc.c
>>  index 44a04fe..4cbe7fb 100644
>>  --- a/drivers/mmc/host/jz4740_mmc.c
>>  +++ b/drivers/mmc/host/jz4740_mmc.c
>>  @@ -43,6 +43,7 @@
>>   #define JZ_REG_MMC_RESP_FIFO   0x34
>>   #define JZ_REG_MMC_RXFIFO      0x38
>>   #define JZ_REG_MMC_TXFIFO      0x3C
>>  +#define JZ_REG_MMC_LPM         0x40
>>   #define JZ_REG_MMC_DMAC                0x44
>> 
>>   #define JZ_MMC_STRPCL_EXIT_MULTIPLE BIT(7)
>>  @@ -102,6 +103,12 @@
>>   #define JZ_MMC_DMAC_DMA_SEL BIT(1)
>>   #define JZ_MMC_DMAC_DMA_EN BIT(0)
>> 
>>  +#define        JZ_MMC_LPM_DRV_RISING BIT(31)
>>  +#define        JZ_MMC_LPM_DRV_RISING_QTR_PHASE_DLY BIT(31)
>>  +#define        JZ_MMC_LPM_DRV_RISING_1NS_DLY BIT(30)
>>  +#define        JZ_MMC_LPM_SMP_RISING_QTR_OR_HALF_PHASE_DLY BIT(29)
>>  +#define        JZ_MMC_LPM_LOW_POWER_MODE_EN BIT(0)
>>  +
>>   #define JZ_MMC_CLK_RATE 24000000
>> 
>>   enum jz4740_mmc_version {
>>  @@ -860,6 +867,22 @@ static int jz4740_mmc_set_clock_rate(struct 
>> jz4740_mmc_host *host, int rate)
>>          }
>> 
>>          writew(div, host->base + JZ_REG_MMC_CLKRT);
>>  +
>>  +       if (real_rate > 25000000) {
>>  +               if (host->version >= JZ_MMC_X1000) {
>>  +                       writel(JZ_MMC_LPM_DRV_RISING_QTR_PHASE_DLY |
>>  +                                  
>> JZ_MMC_LPM_SMP_RISING_QTR_OR_HALF_PHASE_DLY |
>>  +                                  JZ_MMC_LPM_LOW_POWER_MODE_EN,
>>  +                                  host->base + JZ_REG_MMC_LPM);
>>  +               } else if (host->version >= JZ_MMC_JZ4760) {
>>  +                       writel(JZ_MMC_LPM_DRV_RISING |
>>  +                                  JZ_MMC_LPM_LOW_POWER_MODE_EN,
>>  +                                  host->base + JZ_REG_MMC_LPM);
>>  +               } else if (host->version >= JZ_MMC_JZ4725B)
>>  +                       writel(JZ_MMC_LPM_LOW_POWER_MODE_EN,
>>  +                                  host->base + JZ_REG_MMC_LPM);
>>  +       }
>>  +
>>          return real_rate;
>>   }
>> 
>>  --
>>  2.7.4
>> 
>> 


^ permalink raw reply	[flat|nested] 21+ messages in thread

* Re: [PATCH 6/6 v2] MMC: JZ4740: Add support for LPM.
  2019-10-18  8:52     ` Ulf Hansson
  2019-10-18 15:37       ` Paul Cercueil
@ 2019-10-18 16:54       ` Zhou Yanjie
  2019-10-19 20:44         ` Ezequiel Garcia
  1 sibling, 1 reply; 21+ messages in thread
From: Zhou Yanjie @ 2019-10-18 16:54 UTC (permalink / raw)
  To: Ulf Hansson, Paul Cercueil
  Cc: linux-mips, Linux Kernel Mailing List, linux-mmc@vger.kernel.org,
	DTML, Rob Herring, Paul Burton, Mark Rutland, syq, Linus Walleij,
	armijn, Thomas Gleixner, YueHaibing, Mathieu Malaterre,
	Ezequiel Garcia

Hi Uffe,

On 2019年10月18日 16:52, Ulf Hansson wrote:
> On Sat, 12 Oct 2019 at 07:19, Zhou Yanjie <zhouyanjie@zoho.com> wrote:
>> add support for low power mode of Ingenic's MMC/SD Controller.
>>
>> Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
> I couldn't find a proper coverletter for the series, please provide
> that next time as it really helps review.

I'm sorry, maybe some problems with my git send-email cause cover
later not to be sent out, next time I will pay attention to this problem.

> Additionally, it seems like
> you forgot to change the prefix of the patches to "mmc: jz4740" (or at
> least you chosed upper case letters), but I will take care of that
> this time. So, I have applied the series for next, thanks!

I'm very sorry, I have misunderstood, before I thought jz4740 as a proper
noun needs to be capitalized, I will pay attention to this next time.

>
> I also have a general question. Should we perhaps rename the driver
> from jz4740_mmc.c to ingenic.c (and the file for the DT bindings, the
> Kconfig, etc), as that seems like a more appropriate name? No?

I am very much in favor of this proposal. Now jz4740_mmc.c is not only used
for the JZ4740 processor, it is also used for JZ4725, JZ4760, JZ4770, JZ4780
and X1000, and now Ingenic's processor is no longer named after JZ47xx,
it is divided into three product lines: M, T, and X. It is easy to cause 
some
misunderstandings by using jz4740_mmc.c. At the same time, I think that
some register names also need to be adjusted. For example, the STLPPL
register name has only appeared in JZ4730 and JZ4740, and this register
in all subsequent processors is called CTRL. This time I was confused by
the STLPPL when I added drivers for the JZ4760's and X1000's LPM.

I also can send a patch to rename it if you need.

Best regards!

>
> Kind regards
> Uffe
>
>
>> ---
>>   drivers/mmc/host/jz4740_mmc.c | 23 +++++++++++++++++++++++
>>   1 file changed, 23 insertions(+)
>>
>> diff --git a/drivers/mmc/host/jz4740_mmc.c b/drivers/mmc/host/jz4740_mmc.c
>> index 44a04fe..4cbe7fb 100644
>> --- a/drivers/mmc/host/jz4740_mmc.c
>> +++ b/drivers/mmc/host/jz4740_mmc.c
>> @@ -43,6 +43,7 @@
>>   #define JZ_REG_MMC_RESP_FIFO   0x34
>>   #define JZ_REG_MMC_RXFIFO      0x38
>>   #define JZ_REG_MMC_TXFIFO      0x3C
>> +#define JZ_REG_MMC_LPM         0x40
>>   #define JZ_REG_MMC_DMAC                0x44
>>
>>   #define JZ_MMC_STRPCL_EXIT_MULTIPLE BIT(7)
>> @@ -102,6 +103,12 @@
>>   #define JZ_MMC_DMAC_DMA_SEL BIT(1)
>>   #define JZ_MMC_DMAC_DMA_EN BIT(0)
>>
>> +#define        JZ_MMC_LPM_DRV_RISING BIT(31)
>> +#define        JZ_MMC_LPM_DRV_RISING_QTR_PHASE_DLY BIT(31)
>> +#define        JZ_MMC_LPM_DRV_RISING_1NS_DLY BIT(30)
>> +#define        JZ_MMC_LPM_SMP_RISING_QTR_OR_HALF_PHASE_DLY BIT(29)
>> +#define        JZ_MMC_LPM_LOW_POWER_MODE_EN BIT(0)
>> +
>>   #define JZ_MMC_CLK_RATE 24000000
>>
>>   enum jz4740_mmc_version {
>> @@ -860,6 +867,22 @@ static int jz4740_mmc_set_clock_rate(struct jz4740_mmc_host *host, int rate)
>>          }
>>
>>          writew(div, host->base + JZ_REG_MMC_CLKRT);
>> +
>> +       if (real_rate > 25000000) {
>> +               if (host->version >= JZ_MMC_X1000) {
>> +                       writel(JZ_MMC_LPM_DRV_RISING_QTR_PHASE_DLY |
>> +                                  JZ_MMC_LPM_SMP_RISING_QTR_OR_HALF_PHASE_DLY |
>> +                                  JZ_MMC_LPM_LOW_POWER_MODE_EN,
>> +                                  host->base + JZ_REG_MMC_LPM);
>> +               } else if (host->version >= JZ_MMC_JZ4760) {
>> +                       writel(JZ_MMC_LPM_DRV_RISING |
>> +                                  JZ_MMC_LPM_LOW_POWER_MODE_EN,
>> +                                  host->base + JZ_REG_MMC_LPM);
>> +               } else if (host->version >= JZ_MMC_JZ4725B)
>> +                       writel(JZ_MMC_LPM_LOW_POWER_MODE_EN,
>> +                                  host->base + JZ_REG_MMC_LPM);
>> +       }
>> +
>>          return real_rate;
>>   }
>>
>> --
>> 2.7.4
>>
>>

^ permalink raw reply	[flat|nested] 21+ messages in thread

* Re: [PATCH 6/6 v2] MMC: JZ4740: Add support for LPM.
  2019-10-18 16:54       ` Zhou Yanjie
@ 2019-10-19 20:44         ` Ezequiel Garcia
  2019-10-21 14:57           ` Ulf Hansson
  0 siblings, 1 reply; 21+ messages in thread
From: Ezequiel Garcia @ 2019-10-19 20:44 UTC (permalink / raw)
  To: Zhou Yanjie
  Cc: Ulf Hansson, Paul Cercueil, linux-mips, Linux Kernel Mailing List,
	linux-mmc@vger.kernel.org, DTML, Rob Herring, Paul Burton,
	Mark Rutland, syq, Linus Walleij, armijn, Thomas Gleixner,
	YueHaibing, Mathieu Malaterre

On Friday, October 18, 2019 13:54 -03, Zhou Yanjie <zhouyanjie@zoho.com> wrote: 
 

> 
> >
> > I also have a general question. Should we perhaps rename the driver
> > from jz4740_mmc.c to ingenic.c (and the file for the DT bindings, the
> > Kconfig, etc), as that seems like a more appropriate name? No?
> 
> I am very much in favor of this proposal. Now jz4740_mmc.c is not only used
> for the JZ4740 processor, it is also used for JZ4725, JZ4760, JZ4770, JZ4780
> and X1000, and now Ingenic's processor is no longer named after JZ47xx,
> it is divided into three product lines: M, T, and X. It is easy to cause 
> some
> misunderstandings by using jz4740_mmc.c. At the same time, I think that
> some register names also need to be adjusted. For example, the STLPPL
> register name has only appeared in JZ4730 and JZ4740, and this register
> in all subsequent processors is called CTRL. This time I was confused by
> the STLPPL when I added drivers for the JZ4760's and X1000's LPM.
> 

I am very much against renamings, for several reasons. As Paul already mentioned, it's pointless and just adds noise to the git-log, making history harder to recover. Driver file names don't really have to reflect the device exactly. For the compatibility list, it's far easier to just git-grep for compatible strings, or git-grep Documentation and/or Kconfig.

Renaming macros and register names, is equally pointless and equally git-history invasive. Simply adding some documentation is enough.

Thanks,
Ezequiel

^ permalink raw reply	[flat|nested] 21+ messages in thread

* Re: [PATCH 6/6 v2] MMC: JZ4740: Add support for LPM.
  2019-10-19 20:44         ` Ezequiel Garcia
@ 2019-10-21 14:57           ` Ulf Hansson
  0 siblings, 0 replies; 21+ messages in thread
From: Ulf Hansson @ 2019-10-21 14:57 UTC (permalink / raw)
  To: Ezequiel Garcia
  Cc: Zhou Yanjie, Paul Cercueil, linux-mips, Linux Kernel Mailing List,
	linux-mmc@vger.kernel.org, DTML, Rob Herring, Paul Burton,
	Mark Rutland, syq, Linus Walleij, armijn, Thomas Gleixner,
	YueHaibing, Mathieu Malaterre

On Sat, 19 Oct 2019 at 22:44, Ezequiel Garcia
<ezequiel.garcia@collabora.com> wrote:
>
> On Friday, October 18, 2019 13:54 -03, Zhou Yanjie <zhouyanjie@zoho.com> wrote:
>
>
> >
> > >
> > > I also have a general question. Should we perhaps rename the driver
> > > from jz4740_mmc.c to ingenic.c (and the file for the DT bindings, the
> > > Kconfig, etc), as that seems like a more appropriate name? No?
> >
> > I am very much in favor of this proposal. Now jz4740_mmc.c is not only used
> > for the JZ4740 processor, it is also used for JZ4725, JZ4760, JZ4770, JZ4780
> > and X1000, and now Ingenic's processor is no longer named after JZ47xx,
> > it is divided into three product lines: M, T, and X. It is easy to cause
> > some
> > misunderstandings by using jz4740_mmc.c. At the same time, I think that
> > some register names also need to be adjusted. For example, the STLPPL
> > register name has only appeared in JZ4730 and JZ4740, and this register
> > in all subsequent processors is called CTRL. This time I was confused by
> > the STLPPL when I added drivers for the JZ4760's and X1000's LPM.
> >
>
> I am very much against renamings, for several reasons. As Paul already mentioned, it's pointless and just adds noise to the git-log, making history harder to recover. Driver file names don't really have to reflect the device > > exactly. For the compatibility list, it's far easier to just git-grep for compatible strings, or git-grep Documentation and/or Kconfig.

I have no strong opinions. What matters to me, is that people agree on
the best option, based on a case by case discussion.

>
> Renaming macros and register names, is equally pointless and equally git-history invasive. Simply adding some documentation is enough.

Sounds like documentation is what people prefer here - and the DT doc
seems already fine in regards to that.

Perhaps some more words added to the header in driver's c-file could
be and option to consider, as today it only mentions "JZ4740 SD/MMC
controller driver".

Anyway, it's up to you. :-)

Kind regards
Uffe

^ permalink raw reply	[flat|nested] 21+ messages in thread

end of thread, other threads:[~2019-10-21 14:57 UTC | newest]

Thread overview: 21+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
     [not found] <1567669089-88693-1-git-send-email-zhouyanjie@zoho.com>
2019-09-05  7:38 ` [PATCH 2/4] MMC: Ingenic: Add 8bit mode support Zhou Yanjie
2019-09-05  7:38 ` [PATCH 3/4] dt-bindings: MMC: Add JZ4760 bindings Zhou Yanjie
2019-09-13 14:36   ` Rob Herring
2019-09-05  7:38 ` [PATCH 4/4] MMC: Ingenic: Add support for JZ4760 and support for LPM Zhou Yanjie
2019-10-03 10:00   ` Ulf Hansson
2019-10-06  5:58     ` Zhou Yanjie
     [not found] ` <1567669089-88693-2-git-send-email-zhouyanjie@zoho.com>
2019-09-13 15:32   ` [PATCH 1/4] MMC: Ingenic: Adjust the macro definition name Ezequiel Garcia
2019-09-13 15:59     ` Zhou Yanjie
2019-10-12  5:13 ` MMC: JZ4740: Add support for 8bit mode and LPM and JZ4760 Soc v2 Zhou Yanjie
2019-10-12  5:13   ` [PATCH 1/6 v2] MMC: Ingenic: Add 8bit mode support Zhou Yanjie
2019-10-12  5:13   ` [PATCH 2/6 v2] dt-bindings: MMC: Add JZ4760 bindings Zhou Yanjie
2019-10-12  5:13   ` [PATCH 3/6 v2] MMC: JZ4740: Add support for the JZ4760 Zhou Yanjie
2019-10-12  5:13   ` [PATCH 4/6 v2] dt-bindings: MMC: Add X1000 bindings Zhou Yanjie
2019-10-14 18:15     ` Rob Herring
2019-10-12  5:13   ` [PATCH 5/6 v2] MMC: JZ4740: Add support for the X1000 Zhou Yanjie
2019-10-12  5:13   ` [PATCH 6/6 v2] MMC: JZ4740: Add support for LPM Zhou Yanjie
2019-10-18  8:52     ` Ulf Hansson
2019-10-18 15:37       ` Paul Cercueil
2019-10-18 16:54       ` Zhou Yanjie
2019-10-19 20:44         ` Ezequiel Garcia
2019-10-21 14:57           ` Ulf Hansson

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).