Re: [PATCH V2] mmc: dw_mmc: exynos: fix the finding clock sample value

[Jaehoon Chung <jh80.chung@samsung.com>]

On 10/22/21 8:42 PM, Christian Hewitt wrote:
> 
>> On 22 Oct 2021, at 3:35 pm, Marek Szyprowski <m.szyprowski@samsung.com> wrote:
>>
>> Hi,
>>
>> On 22.10.2021 12:53, Christian Hewitt wrote:
>>>> On 22 Oct 2021, at 12:21 pm, Jaehoon Chung <jh80.chung@samsung.com> wrote:
>>>>
>>>> Even though there are candiates value if can't find best value, it's
>>>> returned -EIO. It's not proper behavior.
>>>> If there is not best value, use a first candiate value to work eMMC.
>>>>
>>>> Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
>>>> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
>>> Tested-by: Christian Hewitt <christianshewitt@gmail.com>
>>>
>>> v2 patch working fine with the module that triggered the original report:
>>>
>>> [    2.902144] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
>>> [    2.912118] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
>>> [    3.142474] mmc_host mmc0: Bus speed (slot 0) = 200000000Hz (slot req 200000000Hz, actual 200000000HZ div = 0)
>>> [    3.239339] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0)
>>> [    3.241388] mmc_host mmc0: Bus speed (slot 0) = 266666666Hz (slot req 200000000Hz, actual 133333333HZ div = 1)
>>
>> I wonder why 266666666Hz bus speed is selected instead of the 
>> 400000000Hz one. Did you remove the workaround patch which changed the 
>> divider value from your kernel tree? I didn't analyze the code, so maybe 
>> this change is intentional result of this patch? On my XU4 I get 
>> 400000000Hz bus clock for the eMMC dw-mmc controller.
> 
> Yes, I removed the workaround patch before testing. It’s delivering
> the same result as the workaround so perhaps it’s normal for this
> module. All the emmc modules I have (all samples from HK sent at the
> same time) are identical so there’s nothing else I can test with.

As Marek was mentioned, I wonder why 266666666Hz is selected.
On my XU4, it's selected 400MHz as Marek's. 

Best Regards,
Jaehoon Chung

> 
> Christian
> 
>>> [    3.243310] mmc0: new HS400 MMC card at address 0001
>>> [    3.259191] mmcblk0: mmc0:0001 8GME4R 7.28 GiB
>>> [    3.302621]  mmcblk0: p1 p2
>>> [    3.311541] mmcblk0boot0: mmc0:0001 8GME4R 4.00 MiB
>>> [    3.327737] mmcblk0boot1: mmc0:0001 8GME4R 4.00 MiB
>>> [    3.340919] mmcblk0rpmb: mmc0:0001 8GME4R 512 KiB, chardev (246:0)
>>
>> Best regards
>> -- 
>> Marek Szyprowski, PhD
>> Samsung R&D Institute Poland
> 
>