Re: [PATCH v5 3/9] mmc: core: Add open-ended Ext memory addressing

[Adrian Hunter <adrian.hunter@intel.com>]

On 27/08/24 15:23, Avri Altman wrote:
> For open-ended read/write - just send CMD22 before issuing the command.
> While at it, make sure that the rw command arg is properly casting the
> lower 32 bits, as it can be larger now.
> 
> Tested-by: Ricky WU <ricky_wu@realtek.com>
> Signed-off-by: Avri Altman <avri.altman@wdc.com>
> ---
>  drivers/mmc/core/block.c | 6 +++++-
>  1 file changed, 5 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/mmc/core/block.c b/drivers/mmc/core/block.c
> index 2c9963248fcb..8816b3f0a312 100644
> --- a/drivers/mmc/core/block.c
> +++ b/drivers/mmc/core/block.c
> @@ -180,6 +180,7 @@ static void mmc_blk_rw_rq_prep(struct mmc_queue_req *mqrq,
>  static void mmc_blk_hsq_req_done(struct mmc_request *mrq);
>  static int mmc_spi_err_check(struct mmc_card *card);
>  static int mmc_blk_busy_cb(void *cb_data, bool *busy);
> +static int mmc_blk_wait_for_idle(struct mmc_queue *mq, struct mmc_host *host);
>  
>  static struct mmc_blk_data *mmc_blk_get(struct gendisk *disk)
>  {
> @@ -1664,7 +1665,7 @@ static void mmc_blk_rw_rq_prep(struct mmc_queue_req *mqrq,
>  
>  	brq->mrq.cmd = &brq->cmd;
>  
> -	brq->cmd.arg = blk_rq_pos(req);
> +	brq->cmd.arg = blk_rq_pos(req) & 0xFFFFFFFF;
>  	if (!mmc_card_blockaddr(card))
>  		brq->cmd.arg <<= 9;
>  	brq->cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_ADTC;
> @@ -1712,6 +1713,9 @@ static void mmc_blk_rw_rq_prep(struct mmc_queue_req *mqrq,
>  			(do_data_tag ? (1 << 29) : 0);
>  		brq->sbc.flags = MMC_RSP_R1 | MMC_CMD_AC;
>  		brq->mrq.sbc = &brq->sbc;
> +	} else if (mmc_card_ult_capacity(card)) {
> +		mmc_blk_wait_for_idle(mq, card->host);
> +		mmc_send_ext_addr(card->host, blk_rq_pos(req));

Did you consider having mmc_start_request() send CMD22?
e.g.

diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c
index d6c819dd68ed..22677a01c0e3 100644
--- a/drivers/mmc/core/core.c
+++ b/drivers/mmc/core/core.c
@@ -336,6 +336,9 @@ int mmc_start_request(struct mmc_host *host, struct mmc_request *mrq)
 {
 	int err;
 
+	if (mrq->cmd && mrq->cmd->ext_addr)
+		mmc_send_ext_addr(card->host, mrq->cmd->ext_addr);
+
 	init_completion(&mrq->cmd_completion);
 
 	mmc_retune_hold(host);

>  	}
>  }
>