* [BUG] consistent write corruption on Genesys Logic GL9750 microSD card reader
@ 2026-01-16 18:54 Matthew Schwartz
2026-01-17 2:50 ` Shawn Lin
0 siblings, 1 reply; 3+ messages in thread
From: Matthew Schwartz @ 2026-01-16 18:54 UTC (permalink / raw)
To: Ben Chuang, Victor Shih, Adrian Hunter, Ulf Hansson
Cc: linux-mmc@vger.kernel.org, linux-kernel@vger.kernel.org
Hello,
On a system with a Genesys Logic, Inc GL9750 SD Host Controller [17a0:9750], I am experiencing a consistent amount of corruption on a small number of sectors when running f3write and f3read [1].
This appears on two separate SanDisk Extreme Pro microSD cards (1TB and 2TB) and a Samsung Evo 128GB card.
The corruption is not present if I write the data using these other card readers:
SD Host controller: Genesys Logic, Inc GL9755 SD Host Controller (rev 01)
SD Host controller: Genesys Logic, Inc GL9767 SD Host Controller (rev 04)
and then run f3read on the affected device, so it appears to be specific writing with the GL9750 model. There is nothing related to the card reader or SD card in dmesg when the write corruption occurs, and this issue occurs on every kernel I have tried so far up to 6.19-rc5. I have also tested the same device and SD cards on Windows and no corruption is present when running tests with H2hwtest, which is what f3write/f3read are based on.
The only way around the issue that I have found so far is `sdhci.debug_quirks=0x60` to use PIO instead, as disabling DMA or ADMA individually is not enough to prevent the issue. However, this severely impacts performance [2].
I'm including a full lspci readout for the card reader below at [3] for reference. Is there any more information I can provide to debug this further?
Thanks,
Matt
[1]:
deck@legion-go-s ~ sudo f3write /run/media/deck/SR01T/ -e 3 && sudo f3read /run/media/deck/SR01T/
F3 write 9.0
Copyright (C) 2010 Digirati Internet LTDA.
This is free software; see the source for copying conditions.
Removing old file 1.h2w ...
Free space: 935.72 GB
Creating file 1.h2w ... OK!
Creating file 2.h2w ... OK!
Creating file 3.h2w ... OK!
Free space: 932.72 GB
Average writing speed: 54.10 MB/s
F3 read 9.0
Copyright (C) 2010 Digirati Internet LTDA.
This is free software; see the source for copying conditions.
SECTORS ok/corrupted/changed/overwritten
Validating file 1.h2w ... 2097099/ 53/ 0/ 0
Validating file 2.h2w ... 2097077/ 75/ 0/ 0
Validating file 3.h2w ... 2097087/ 65/ 0/ 0
Data OK: 3.00 GB (6291263 sectors)
Data LOST: 96.50 KB (193 sectors)
Corrupted: 96.50 KB (193 sectors)
Slightly changed: 0.00 Byte (0 sectors)
Overwritten: 0.00 Byte (0 sectors)
Average reading speed: 85.62 MB/s
[2]:
deck@legion-go-s ~> sudo f3write /run/media/deck/SR01T/ -e 1 && sudo f3read /run/media/deck/SR01T/
F3 write 9.0
Copyright (C) 2010 Digirati Internet LTDA.
This is free software; see the source for copying conditions.
Removing old file 1.h2w ...
Free space: 935.09 GB
Creating file 1.h2w ... OK!
Free space: 934.72 GB
Average writing speed: 24.22 MB/s
F3 read 9.0
Copyright (C) 2010 Digirati Internet LTDA.
This is free software; see the source for copying conditions.
SECTORS ok/corrupted/changed/overwritten
Validating file 1.h2w ... 2097152/ 0/ 0/ 0
Data OK: 1.00 GB (2097152 sectors)
Data LOST: 0.00 Byte (0 sectors)
Corrupted: 0.00 Byte (0 sectors)
Slightly changed: 0.00 Byte (0 sectors)
Overwritten: 0.00 Byte (0 sectors)
Average reading speed: 3.07 MB/s
[3]:
02:00.0 SD Host controller: Genesys Logic, Inc GL9750 SD Host Controller (rev 01) (prog-if 01)
Subsystem: Genesys Logic, Inc GL9750 SD Host Controller
Physical Slot: 0
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 55
Region 0: Memory at b0a00000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [80] Express (v2) Endpoint, IntMsgNum 0
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 <64us
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 75W TEE-IO-
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
LnkCap: Port #80, Speed 2.5GT/s, Width x1, ASPM L1, Exit Latency L1 <64us
ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
LnkCtl: ASPM L1 Enabled; RCB 64 bytes, LnkDisable- CommClk+
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt- FltModeDis-
LnkSta: Speed 2.5GT/s, Width x1
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ NROPrPrP- LTR+
10BitTagComp- 10BitTagReq- OBFF Via message/WAKE#, ExtFmt- EETLPPrefix-
EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
FRS- TPHComp- ExtTPHComp-
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
AtomicOpsCtl: ReqEn-
IDOReq- IDOCompl- LTR+ EmergencyPowerReductionReq-
10BitTagReq- OBFF Disabled, EETLPPrefixBlk-
LnkCap2: Supported Link Speeds: 2.5GT/s, Crosslink- Retimer- 2Retimers- DRS-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance Preset/De-emphasis: -6dB de-emphasis, 0dB preshoot
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1-
EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
Retimer- 2Retimers- CrosslinkRes: unsupported, FltMode-
Capabilities: [e0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee04000 Data: 0022
Capabilities: [f8] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Vendor Specific Information: ID=17a0 Rev=1 Len=008 <?>
Capabilities: [108 v1] Latency Tolerance Reporting
Max snoop latency: 1048576ns
Max no snoop latency: 1048576ns
Capabilities: [110 v1] L1 PM Substates
L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+
PortCommonModeRestoreTime=20us PortTPowerOnTime=4us
L1SubCtl1: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+
T_CommonMode=0us LTR1.2_Threshold=176128ns
L1SubCtl2: T_PwrOn=150us
Capabilities: [200 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP-
ECRC- UnsupReq- ACSViol- UncorrIntErr- BlockedTLP- AtomicOpBlocked- TLPBlockedErr-
PoisonTLPBlocked- DMWrReqBlocked- IDECheck- MisIDETLP- PCRC_CHECK- TLPXlatBlocked-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP-
ECRC- UnsupReq- ACSViol- UncorrIntErr- BlockedTLP- AtomicOpBlocked- TLPBlockedErr-
PoisonTLPBlocked- DMWrReqBlocked- IDECheck- MisIDETLP- PCRC_CHECK- TLPXlatBlocked-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+
ECRC- UnsupReq- ACSViol- UncorrIntErr- BlockedTLP- AtomicOpBlocked- TLPBlockedErr-
PoisonTLPBlocked- DMWrReqBlocked- IDECheck- MisIDETLP- PCRC_CHECK- TLPXlatBlocked-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr- CorrIntErr- HeaderOF-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout+ AdvNonFatalErr+ CorrIntErr- HeaderOF-
AERCap: First Error Pointer: 00, ECRCGenCap- ECRCGenEn- ECRCChkCap- ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog: 4a000040 00130200 02000900 01000000
Kernel driver in use: sdhci-pci
Kernel modules: sdhci_pci
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [BUG] consistent write corruption on Genesys Logic GL9750 microSD card reader
2026-01-16 18:54 [BUG] consistent write corruption on Genesys Logic GL9750 microSD card reader Matthew Schwartz
@ 2026-01-17 2:50 ` Shawn Lin
2026-01-17 5:38 ` Matthew Schwartz
0 siblings, 1 reply; 3+ messages in thread
From: Shawn Lin @ 2026-01-17 2:50 UTC (permalink / raw)
To: Matthew Schwartz, Ben Chuang, Victor Shih, Adrian Hunter,
Ulf Hansson
Cc: shawn.lin, linux-mmc@vger.kernel.org,
linux-kernel@vger.kernel.org
在 2026/01/17 星期六 2:54, Matthew Schwartz 写道:
> Hello,
>
> On a system with a Genesys Logic, Inc GL9750 SD Host Controller [17a0:9750], I am experiencing a consistent amount of corruption on a small number of sectors when running f3write and f3read [1].
>
> This appears on two separate SanDisk Extreme Pro microSD cards (1TB and 2TB) and a Samsung Evo 128GB card.
>
> The corruption is not present if I write the data using these other card readers:
>
> SD Host controller: Genesys Logic, Inc GL9755 SD Host Controller (rev 01)
> SD Host controller: Genesys Logic, Inc GL9767 SD Host Controller (rev 04)
>
> and then run f3read on the affected device, so it appears to be specific writing with the GL9750 model. There is nothing related to the card reader or SD card in dmesg when the write corruption occurs, and this issue occurs on every kernel I have tried so far up to 6.19-rc5. I have also tested the same device and SD cards on Windows and no corruption is present when running tests with H2hwtest, which is what f3write/f3read are based on.
>
> The only way around the issue that I have found so far is `sdhci.debug_quirks=0x60` to use PIO instead, as disabling DMA or ADMA individually is not enough to prevent the issue. However, this severely impacts performance [2].
>
> I'm including a full lspci readout for the card reader below at [3] for reference. Is there any more information I can provide to debug this further?
>
> Thanks,
> Matt
>
> [1]:
> deck@legion-go-s ~ sudo f3write /run/media/deck/SR01T/ -e 3 && sudo f3read /run/media/deck/SR01T/
> F3 write 9.0
> Copyright (C) 2010 Digirati Internet LTDA.
> This is free software; see the source for copying conditions.
>
> Removing old file 1.h2w ...
> Free space: 935.72 GB
> Creating file 1.h2w ... OK!
> Creating file 2.h2w ... OK!
> Creating file 3.h2w ... OK!
> Free space: 932.72 GB
> Average writing speed: 54.10 MB/s
> F3 read 9.0
> Copyright (C) 2010 Digirati Internet LTDA.
> This is free software; see the source for copying conditions.
>
> SECTORS ok/corrupted/changed/overwritten
> Validating file 1.h2w ... 2097099/ 53/ 0/ 0
> Validating file 2.h2w ... 2097077/ 75/ 0/ 0
> Validating file 3.h2w ... 2097087/ 65/ 0/ 0
>
> Data OK: 3.00 GB (6291263 sectors)
> Data LOST: 96.50 KB (193 sectors)
> Corrupted: 96.50 KB (193 sectors)
> Slightly changed: 0.00 Byte (0 sectors)
> Overwritten: 0.00 Byte (0 sectors)
> Average reading speed: 85.62 MB/s
>
> [2]:
> deck@legion-go-s ~> sudo f3write /run/media/deck/SR01T/ -e 1 && sudo f3read /run/media/deck/SR01T/
> F3 write 9.0
> Copyright (C) 2010 Digirati Internet LTDA.
> This is free software; see the source for copying conditions.
>
> Removing old file 1.h2w ...
> Free space: 935.09 GB
> Creating file 1.h2w ... OK!
> Free space: 934.72 GB
> Average writing speed: 24.22 MB/s
> F3 read 9.0
> Copyright (C) 2010 Digirati Internet LTDA.
> This is free software; see the source for copying conditions.
>
> SECTORS ok/corrupted/changed/overwritten
> Validating file 1.h2w ... 2097152/ 0/ 0/ 0
>
> Data OK: 1.00 GB (2097152 sectors)
> Data LOST: 0.00 Byte (0 sectors)
> Corrupted: 0.00 Byte (0 sectors)
> Slightly changed: 0.00 Byte (0 sectors)
> Overwritten: 0.00 Byte (0 sectors)
> Average reading speed: 3.07 MB/s
>
> [3]:
> 02:00.0 SD Host controller: Genesys Logic, Inc GL9750 SD Host Controller (rev 01) (prog-if 01)
> Subsystem: Genesys Logic, Inc GL9750 SD Host Controller
> Physical Slot: 0
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 55
> Region 0: Memory at b0a00000 (32-bit, non-prefetchable) [size=4K]
> Capabilities: [80] Express (v2) Endpoint, IntMsgNum 0
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 <64us
> ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 75W TEE-IO-
> DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
> RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 512 bytes
> DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
> LnkCap: Port #80, Speed 2.5GT/s, Width x1, ASPM L1, Exit Latency L1 <64us
> ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
> LnkCtl: ASPM L1 Enabled; RCB 64 bytes, LnkDisable- CommClk+
> ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt- FltModeDis-
> LnkSta: Speed 2.5GT/s, Width x1
> TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
> DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ NROPrPrP- LTR+
> 10BitTagComp- 10BitTagReq- OBFF Via message/WAKE#, ExtFmt- EETLPPrefix-
> EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
> FRS- TPHComp- ExtTPHComp-
> AtomicOpsCap: 32bit- 64bit- 128bitCAS-
> DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
> AtomicOpsCtl: ReqEn-
> IDOReq- IDOCompl- LTR+ EmergencyPowerReductionReq-
> 10BitTagReq- OBFF Disabled, EETLPPrefixBlk-
> LnkCap2: Supported Link Speeds: 2.5GT/s, Crosslink- Retimer- 2Retimers- DRS-
> LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
> Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
> Compliance Preset/De-emphasis: -6dB de-emphasis, 0dB preshoot
> LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1-
> EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
> Retimer- 2Retimers- CrosslinkRes: unsupported, FltMode-
> Capabilities: [e0] MSI: Enable+ Count=1/1 Maskable- 64bit+
> Address: 00000000fee04000 Data: 0022
> Capabilities: [f8] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
> Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [100 v1] Vendor Specific Information: ID=17a0 Rev=1 Len=008 <?>
> Capabilities: [108 v1] Latency Tolerance Reporting
> Max snoop latency: 1048576ns
> Max no snoop latency: 1048576ns
> Capabilities: [110 v1] L1 PM Substates
> L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+
> PortCommonModeRestoreTime=20us PortTPowerOnTime=4us
> L1SubCtl1: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+
> T_CommonMode=0us LTR1.2_Threshold=176128ns
Just chiming in, I vaguely remember there was a reported regarding to
GL9750's ASPM, more precisely L1 substate support. Not sure if it's
related to your problem, but worth a try by disabling the ASPM support.
--- a/drivers/pci/quirks.c
+++ b/drivers/pci/quirks.c
@@ -2526,6 +2526,7 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ASMEDIA,
0x1080, quirk_disable_aspm_l0s_l
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_FREESCALE, 0x0451,
quirk_disable_aspm_l0s_l1);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_PASEMI, 0xa002,
quirk_disable_aspm_l0s_l1);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_HUAWEI, 0x1105,
quirk_disable_aspm_l0s_l1);
+DECLARE_PCI_FIXUP_HEADER(0x17a0, 0x9750, quirk_disable_aspm_l0s_l1);
> L1SubCtl2: T_PwrOn=150us
> Capabilities: [200 v1] Advanced Error Reporting
> UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP-
> ECRC- UnsupReq- ACSViol- UncorrIntErr- BlockedTLP- AtomicOpBlocked- TLPBlockedErr-
> PoisonTLPBlocked- DMWrReqBlocked- IDECheck- MisIDETLP- PCRC_CHECK- TLPXlatBlocked-
> UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP-
> ECRC- UnsupReq- ACSViol- UncorrIntErr- BlockedTLP- AtomicOpBlocked- TLPBlockedErr-
> PoisonTLPBlocked- DMWrReqBlocked- IDECheck- MisIDETLP- PCRC_CHECK- TLPXlatBlocked-
> UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+
> ECRC- UnsupReq- ACSViol- UncorrIntErr- BlockedTLP- AtomicOpBlocked- TLPBlockedErr-
> PoisonTLPBlocked- DMWrReqBlocked- IDECheck- MisIDETLP- PCRC_CHECK- TLPXlatBlocked-
> CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr- CorrIntErr- HeaderOF-
> CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout+ AdvNonFatalErr+ CorrIntErr- HeaderOF-
> AERCap: First Error Pointer: 00, ECRCGenCap- ECRCGenEn- ECRCChkCap- ECRCChkEn-
> MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
> HeaderLog: 4a000040 00130200 02000900 01000000
> Kernel driver in use: sdhci-pci
> Kernel modules: sdhci_pci
>
>
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [BUG] consistent write corruption on Genesys Logic GL9750 microSD card reader
2026-01-17 2:50 ` Shawn Lin
@ 2026-01-17 5:38 ` Matthew Schwartz
0 siblings, 0 replies; 3+ messages in thread
From: Matthew Schwartz @ 2026-01-17 5:38 UTC (permalink / raw)
To: Shawn Lin, Ben Chuang, Victor Shih, Adrian Hunter, Ulf Hansson
Cc: linux-mmc@vger.kernel.org, linux-kernel@vger.kernel.org
On 1/16/26 6:50 PM, Shawn Lin wrote:
> 在 2026/01/17 星期六 2:54, Matthew Schwartz 写道:
>> Hello,
>>
>> On a system with a Genesys Logic, Inc GL9750 SD Host Controller [17a0:9750], I am experiencing a consistent amount of corruption on a small number of sectors when running f3write and f3read [1].
>>
>> This appears on two separate SanDisk Extreme Pro microSD cards (1TB and 2TB) and a Samsung Evo 128GB card.
>>
>> The corruption is not present if I write the data using these other card readers:
>>
>> SD Host controller: Genesys Logic, Inc GL9755 SD Host Controller (rev 01)
>> SD Host controller: Genesys Logic, Inc GL9767 SD Host Controller (rev 04)
>>
>> and then run f3read on the affected device, so it appears to be specific writing with the GL9750 model. There is nothing related to the card reader or SD card in dmesg when the write corruption occurs, and this issue occurs on every kernel I have tried so far up to 6.19-rc5. I have also tested the same device and SD cards on Windows and no corruption is present when running tests with H2hwtest, which is what f3write/f3read are based on.
>>
>> The only way around the issue that I have found so far is `sdhci.debug_quirks=0x60` to use PIO instead, as disabling DMA or ADMA individually is not enough to prevent the issue. However, this severely impacts performance [2].
>>
>> I'm including a full lspci readout for the card reader below at [3] for reference. Is there any more information I can provide to debug this further?
>>
>> Thanks,
>> Matt
>>
>> [1]:
>> deck@legion-go-s ~ sudo f3write /run/media/deck/SR01T/ -e 3 && sudo f3read /run/media/deck/SR01T/
>> F3 write 9.0
>> Copyright (C) 2010 Digirati Internet LTDA.
>> This is free software; see the source for copying conditions.
>>
>> Removing old file 1.h2w ...
>> Free space: 935.72 GB
>> Creating file 1.h2w ... OK!
>> Creating file 2.h2w ... OK!
>> Creating file 3.h2w ... OK!
>> Free space: 932.72 GB
>> Average writing speed: 54.10 MB/s
>> F3 read 9.0
>> Copyright (C) 2010 Digirati Internet LTDA.
>> This is free software; see the source for copying conditions.
>>
>> SECTORS ok/corrupted/changed/overwritten
>> Validating file 1.h2w ... 2097099/ 53/ 0/ 0
>> Validating file 2.h2w ... 2097077/ 75/ 0/ 0
>> Validating file 3.h2w ... 2097087/ 65/ 0/ 0
>>
>> Data OK: 3.00 GB (6291263 sectors)
>> Data LOST: 96.50 KB (193 sectors)
>> Corrupted: 96.50 KB (193 sectors)
>> Slightly changed: 0.00 Byte (0 sectors)
>> Overwritten: 0.00 Byte (0 sectors)
>> Average reading speed: 85.62 MB/s
>>
>> [2]:
>> deck@legion-go-s ~> sudo f3write /run/media/deck/SR01T/ -e 1 && sudo f3read /run/media/deck/SR01T/
>> F3 write 9.0
>> Copyright (C) 2010 Digirati Internet LTDA.
>> This is free software; see the source for copying conditions.
>>
>> Removing old file 1.h2w ...
>> Free space: 935.09 GB
>> Creating file 1.h2w ... OK!
>> Free space: 934.72 GB
>> Average writing speed: 24.22 MB/s
>> F3 read 9.0
>> Copyright (C) 2010 Digirati Internet LTDA.
>> This is free software; see the source for copying conditions.
>>
>> SECTORS ok/corrupted/changed/overwritten
>> Validating file 1.h2w ... 2097152/ 0/ 0/ 0
>>
>> Data OK: 1.00 GB (2097152 sectors)
>> Data LOST: 0.00 Byte (0 sectors)
>> Corrupted: 0.00 Byte (0 sectors)
>> Slightly changed: 0.00 Byte (0 sectors)
>> Overwritten: 0.00 Byte (0 sectors)
>> Average reading speed: 3.07 MB/s
>>
>> [3]:
>> 02:00.0 SD Host controller: Genesys Logic, Inc GL9750 SD Host Controller (rev 01) (prog-if 01)
>> Subsystem: Genesys Logic, Inc GL9750 SD Host Controller
>> Physical Slot: 0
>> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
>> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
>> Latency: 0, Cache Line Size: 64 bytes
>> Interrupt: pin A routed to IRQ 55
>> Region 0: Memory at b0a00000 (32-bit, non-prefetchable) [size=4K]
>> Capabilities: [80] Express (v2) Endpoint, IntMsgNum 0
>> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 <64us
>> ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 75W TEE-IO-
>> DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
>> RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
>> MaxPayload 128 bytes, MaxReadReq 512 bytes
>> DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
>> LnkCap: Port #80, Speed 2.5GT/s, Width x1, ASPM L1, Exit Latency L1 <64us
>> ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
>> LnkCtl: ASPM L1 Enabled; RCB 64 bytes, LnkDisable- CommClk+
>> ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt- FltModeDis-
>> LnkSta: Speed 2.5GT/s, Width x1
>> TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
>> DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ NROPrPrP- LTR+
>> 10BitTagComp- 10BitTagReq- OBFF Via message/WAKE#, ExtFmt- EETLPPrefix-
>> EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
>> FRS- TPHComp- ExtTPHComp-
>> AtomicOpsCap: 32bit- 64bit- 128bitCAS-
>> DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
>> AtomicOpsCtl: ReqEn-
>> IDOReq- IDOCompl- LTR+ EmergencyPowerReductionReq-
>> 10BitTagReq- OBFF Disabled, EETLPPrefixBlk-
>> LnkCap2: Supported Link Speeds: 2.5GT/s, Crosslink- Retimer- 2Retimers- DRS-
>> LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
>> Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
>> Compliance Preset/De-emphasis: -6dB de-emphasis, 0dB preshoot
>> LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1-
>> EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
>> Retimer- 2Retimers- CrosslinkRes: unsupported, FltMode-
>> Capabilities: [e0] MSI: Enable+ Count=1/1 Maskable- 64bit+
>> Address: 00000000fee04000 Data: 0022
>> Capabilities: [f8] Power Management version 3
>> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
>> Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
>> Capabilities: [100 v1] Vendor Specific Information: ID=17a0 Rev=1 Len=008 <?>
>> Capabilities: [108 v1] Latency Tolerance Reporting
>> Max snoop latency: 1048576ns
>> Max no snoop latency: 1048576ns
>> Capabilities: [110 v1] L1 PM Substates
>> L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+
>> PortCommonModeRestoreTime=20us PortTPowerOnTime=4us
>> L1SubCtl1: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+
>> T_CommonMode=0us LTR1.2_Threshold=176128ns
>
> Just chiming in, I vaguely remember there was a reported regarding to
> GL9750's ASPM, more precisely L1 substate support. Not sure if it's
> related to your problem, but worth a try by disabling the ASPM support.
Unfortunately it does not seem to affect this issue:
deck@legion-go-s ~> sudo f3write /run/media/deck/SR01T/ -e 1 && sudo f3read /run/media/deck/SR01T/
F3 write 9.0
Copyright (C) 2010 Digirati Internet LTDA.
This is free software; see the source for copying conditions.
Removing old file 1.h2w ...
Free space: 935.72 GB
Creating file 1.h2w ... OK!
Free space: 934.72 GB
Average writing speed: 55.20 MB/s
F3 read 9.0
Copyright (C) 2010 Digirati Internet LTDA.
This is free software; see the source for copying conditions.
SECTORS ok/corrupted/changed/overwritten
Validating file 1.h2w ... 2097066/ 86/ 0/ 0
Data OK: 1023.96 MB (2097066 sectors)
Data LOST: 43.00 KB (86 sectors)
Corrupted: 43.00 KB (86 sectors)
Slightly changed: 0.00 Byte (0 sectors)
Overwritten: 0.00 Byte (0 sectors)
Average reading speed: 86.24 MB/s
Thanks for the suggestion though!
I did look a bit more into past GL9750 issues, and I found a few comments on an unrelated bugzilla report that had identical symptoms to what I reported in this thread: https://bugzilla.kernel.org/show_bug.cgi?id=204161#c7
Matt
>
> --- a/drivers/pci/quirks.c
> +++ b/drivers/pci/quirks.c
> @@ -2526,6 +2526,7 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ASMEDIA, 0x1080, quirk_disable_aspm_l0s_l
> DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_FREESCALE, 0x0451, quirk_disable_aspm_l0s_l1);
> DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_PASEMI, 0xa002, quirk_disable_aspm_l0s_l1);
> DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_HUAWEI, 0x1105, quirk_disable_aspm_l0s_l1);
> +DECLARE_PCI_FIXUP_HEADER(0x17a0, 0x9750, quirk_disable_aspm_l0s_l1);
>
>
>
>> L1SubCtl2: T_PwrOn=150us
>> Capabilities: [200 v1] Advanced Error Reporting
>> UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP-
>> ECRC- UnsupReq- ACSViol- UncorrIntErr- BlockedTLP- AtomicOpBlocked- TLPBlockedErr-
>> PoisonTLPBlocked- DMWrReqBlocked- IDECheck- MisIDETLP- PCRC_CHECK- TLPXlatBlocked-
>> UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP-
>> ECRC- UnsupReq- ACSViol- UncorrIntErr- BlockedTLP- AtomicOpBlocked- TLPBlockedErr-
>> PoisonTLPBlocked- DMWrReqBlocked- IDECheck- MisIDETLP- PCRC_CHECK- TLPXlatBlocked-
>> UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+
>> ECRC- UnsupReq- ACSViol- UncorrIntErr- BlockedTLP- AtomicOpBlocked- TLPBlockedErr-
>> PoisonTLPBlocked- DMWrReqBlocked- IDECheck- MisIDETLP- PCRC_CHECK- TLPXlatBlocked-
>> CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr- CorrIntErr- HeaderOF-
>> CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout+ AdvNonFatalErr+ CorrIntErr- HeaderOF-
>> AERCap: First Error Pointer: 00, ECRCGenCap- ECRCGenEn- ECRCChkCap- ECRCChkEn-
>> MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
>> HeaderLog: 4a000040 00130200 02000900 01000000
>> Kernel driver in use: sdhci-pci
>> Kernel modules: sdhci_pci
>>
>>
>
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2026-01-17 5:38 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2026-01-16 18:54 [BUG] consistent write corruption on Genesys Logic GL9750 microSD card reader Matthew Schwartz
2026-01-17 2:50 ` Shawn Lin
2026-01-17 5:38 ` Matthew Schwartz
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox