From: zhangfei gao <zhangfei.gao@gmail.com>
To: Arindam Nath <arindam.nath@amd.com>
Cc: cjb@laptop.org, prakity@marvell.com, subhashj@codeaurora.org,
linux-mmc@vger.kernel.org, henry.su@amd.com, aaron.lu@amd.com,
anath.amd@gmail.com
Subject: Re: [PATCH v4 03/15] mmc: sd: add support for driver type selection
Date: Fri, 6 May 2011 06:37:42 -0400 [thread overview]
Message-ID: <BANLkTik-WnPx-ssEE+aFdBYj86YbBD3Wtw@mail.gmail.com> (raw)
In-Reply-To: <1304578151-1775-4-git-send-email-arindam.nath@amd.com>
On Thu, May 5, 2011 at 2:48 AM, Arindam Nath <arindam.nath@amd.com> wrote:
> This patch adds support for setting driver strength during UHS-I
> initialization prcedure. Since UHS-I cards set S18A (bit 24) in
> response to ACMD41, we use this as a base for UHS-I initialization.
> We modify the parameter list of mmc_sd_get_cid() so that we can
> save the ROCR from ACMD41 to check whether bit 24 is set.
>
> We decide whether the Host Controller supports A, C, or D driver
> type depending on the Capabilities register. Driver type B is
> suported by default. We then set the appropriate driver type for
> the card using CMD6 mode 1. As per Host Controller spec v3.00, we
> set driver type for the host only if Preset Value Enable in the
> Host Control2 register is not set. SDHCI_HOST_CONTROL has been
> renamed to SDHCI_HOST_CONTROL1 to conform to the spec.
>
> Signed-off-by: Arindam Nath <arindam.nath@amd.com>
> Reviewed-by: Philip Rakity <prakity@marvell.com>
> Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao<zhangfei.gao@marvell.com>
Verified with Toshiba uhs card and general hs card, on mmp2 in SDMA mode.
> ---
> drivers/mmc/core/core.c | 9 +++
> drivers/mmc/core/core.h | 1 +
> drivers/mmc/core/sd.c | 153 ++++++++++++++++++++++++++++++++++++++--------
> drivers/mmc/core/sd.h | 3 +-
> drivers/mmc/core/sdio.c | 3 +-
> drivers/mmc/host/sdhci.c | 49 +++++++++++---
> drivers/mmc/host/sdhci.h | 11 +++-
> include/linux/mmc/card.h | 4 +
> include/linux/mmc/host.h | 10 +++
> 9 files changed, 203 insertions(+), 40 deletions(-)
>
> diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c
> index ea5c28d..78a9b51 100644
> --- a/drivers/mmc/core/core.c
> +++ b/drivers/mmc/core/core.c
> @@ -986,6 +986,15 @@ void mmc_set_timing(struct mmc_host *host, unsigned int timing)
> }
>
> /*
> + * Select appropriate driver type for host.
> + */
> +void mmc_set_driver_type(struct mmc_host *host, unsigned int drv_type)
> +{
> + host->ios.drv_type = drv_type;
> + mmc_set_ios(host);
> +}
> +
> +/*
> * Apply power to the MMC stack. This is a two-stage process.
> * First, we enable power to the card without the clock running.
> * We then wait a bit for the power to stabilise. Finally,
> diff --git a/drivers/mmc/core/core.h b/drivers/mmc/core/core.h
> index 7745dea..93f3397 100644
> --- a/drivers/mmc/core/core.h
> +++ b/drivers/mmc/core/core.h
> @@ -43,6 +43,7 @@ void mmc_set_bus_width_ddr(struct mmc_host *host, unsigned int width,
> u32 mmc_select_voltage(struct mmc_host *host, u32 ocr);
> int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage);
> void mmc_set_timing(struct mmc_host *host, unsigned int timing);
> +void mmc_set_driver_type(struct mmc_host *host, unsigned int drv_type);
>
> static inline void mmc_delay(unsigned int ms)
> {
> diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c
> index d4410c9..a6fa52f 100644
> --- a/drivers/mmc/core/sd.c
> +++ b/drivers/mmc/core/sd.c
> @@ -405,6 +405,98 @@ out:
> return err;
> }
>
> +static int sd_select_driver_type(struct mmc_card *card, u8 *status)
> +{
> + int host_drv_type = 0, card_drv_type = 0;
> + int err;
> +
> + /*
> + * If the host doesn't support any of the Driver Types A,C or D,
> + * default Driver Type B is used.
> + */
> + if (!(card->host->caps & (MMC_CAP_DRIVER_TYPE_A | MMC_CAP_DRIVER_TYPE_C
> + | MMC_CAP_DRIVER_TYPE_D)))
> + return 0;
> +
> + if (card->host->caps & MMC_CAP_DRIVER_TYPE_A) {
> + host_drv_type = MMC_SET_DRIVER_TYPE_A;
> + if (card->sw_caps.sd3_drv_type & SD_DRIVER_TYPE_A)
> + card_drv_type = MMC_SET_DRIVER_TYPE_A;
> + else if (card->sw_caps.sd3_drv_type & SD_DRIVER_TYPE_B)
> + card_drv_type = MMC_SET_DRIVER_TYPE_B;
> + else if (card->sw_caps.sd3_drv_type & SD_DRIVER_TYPE_C)
> + card_drv_type = MMC_SET_DRIVER_TYPE_C;
> + } else if (card->host->caps & MMC_CAP_DRIVER_TYPE_C) {
> + host_drv_type = MMC_SET_DRIVER_TYPE_C;
> + if (card->sw_caps.sd3_drv_type & SD_DRIVER_TYPE_C)
> + card_drv_type = MMC_SET_DRIVER_TYPE_C;
> + } else if (!(card->host->caps & MMC_CAP_DRIVER_TYPE_D)) {
> + /*
> + * If we are here, that means only the default driver type
> + * B is supported by the host.
> + */
> + host_drv_type = MMC_SET_DRIVER_TYPE_B;
> + if (card->sw_caps.sd3_drv_type & SD_DRIVER_TYPE_B)
> + card_drv_type = MMC_SET_DRIVER_TYPE_B;
> + else if (card->sw_caps.sd3_drv_type & SD_DRIVER_TYPE_C)
> + card_drv_type = MMC_SET_DRIVER_TYPE_C;
> + }
> +
> + err = mmc_sd_switch(card, 1, 2, card_drv_type, status);
> + if (err)
> + return err;
> +
> + if ((status[15] & 0xF) != card_drv_type) {
> + printk(KERN_WARNING "%s: Problem setting driver strength!\n",
> + mmc_hostname(card->host));
> + return 0;
> + }
> +
> + mmc_set_driver_type(card->host, host_drv_type);
> +
> + return 0;
> +}
> +
> +/*
> + * UHS-I specific initialization procedure
> + */
> +static int mmc_sd_init_uhs_card(struct mmc_card *card)
> +{
> + int err;
> + u8 *status;
> +
> + if (!card->scr.sda_spec3)
> + return 0;
> +
> + if (!(card->csd.cmdclass & CCC_SWITCH))
> + return 0;
> +
> + status = kmalloc(64, GFP_KERNEL);
> + if (!status) {
> + printk(KERN_ERR "%s: could not allocate a buffer for "
> + "switch capabilities.\n", mmc_hostname(card->host));
> + return -ENOMEM;
> + }
> +
> + /* Set 4-bit bus width */
> + if ((card->host->caps & MMC_CAP_4_BIT_DATA) &&
> + (card->scr.bus_widths & SD_SCR_BUS_WIDTH_4)) {
> + err = mmc_app_set_bus_width(card, MMC_BUS_WIDTH_4);
> + if (err)
> + goto out;
> +
> + mmc_set_bus_width(card->host, MMC_BUS_WIDTH_4);
> + }
> +
> + /* Set the driver strength for the card */
> + err = sd_select_driver_type(card, status);
> +
> +out:
> + kfree(status);
> +
> + return err;
> +}
> +
> MMC_DEV_ATTR(cid, "%08x%08x%08x%08x\n", card->raw_cid[0], card->raw_cid[1],
> card->raw_cid[2], card->raw_cid[3]);
> MMC_DEV_ATTR(csd, "%08x%08x%08x%08x\n", card->raw_csd[0], card->raw_csd[1],
> @@ -453,10 +545,10 @@ struct device_type sd_type = {
> /*
> * Fetch CID from card.
> */
> -int mmc_sd_get_cid(struct mmc_host *host, u32 ocr, u32 *cid)
> +int mmc_sd_get_cid(struct mmc_host *host, u32 ocr, u32 *cid,
> + u32 *rocr)
> {
> int err;
> - u32 rocr;
>
> /*
> * Since we're changing the OCR value, we seem to
> @@ -490,7 +582,7 @@ int mmc_sd_get_cid(struct mmc_host *host, u32 ocr, u32 *cid)
> ocr |= SD_OCR_XPC;
>
> try_again:
> - err = mmc_send_app_op_cond(host, ocr, &rocr);
> + err = mmc_send_app_op_cond(host, ocr, rocr);
> if (err)
> return err;
>
> @@ -498,7 +590,8 @@ try_again:
> * In case CCS and S18A in the response is set, start Signal Voltage
> * Switch procedure. SPI mode doesn't support CMD11.
> */
> - if (!mmc_host_is_spi(host) && ((rocr & 0x41000000) == 0x41000000)) {
> + if (!mmc_host_is_spi(host) && rocr &&
> + ((*rocr & 0x41000000) == 0x41000000)) {
> err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180);
> if (err) {
> ocr &= ~SD_OCR_S18R;
> @@ -633,11 +726,12 @@ static int mmc_sd_init_card(struct mmc_host *host, u32 ocr,
> struct mmc_card *card;
> int err;
> u32 cid[4];
> + u32 rocr = 0;
>
> BUG_ON(!host);
> WARN_ON(!host->claimed);
>
> - err = mmc_sd_get_cid(host, ocr, cid);
> + err = mmc_sd_get_cid(host, ocr, cid, &rocr);
> if (err)
> return err;
>
> @@ -690,30 +784,37 @@ static int mmc_sd_init_card(struct mmc_host *host, u32 ocr,
> if (err)
> goto free_card;
>
> - /*
> - * Attempt to change to high-speed (if supported)
> - */
> - err = mmc_sd_switch_hs(card);
> - if (err > 0)
> - mmc_sd_go_highspeed(card);
> - else if (err)
> - goto free_card;
> -
> - /*
> - * Set bus speed.
> - */
> - mmc_set_clock(host, mmc_sd_get_max_clock(card));
> -
> - /*
> - * Switch to wider bus (if supported).
> - */
> - if ((host->caps & MMC_CAP_4_BIT_DATA) &&
> - (card->scr.bus_widths & SD_SCR_BUS_WIDTH_4)) {
> - err = mmc_app_set_bus_width(card, MMC_BUS_WIDTH_4);
> + /* Initialization sequence for UHS-I cards */
> + if (rocr & SD_ROCR_S18A) {
> + err = mmc_sd_init_uhs_card(card);
> if (err)
> goto free_card;
> + } else {
> + /*
> + * Attempt to change to high-speed (if supported)
> + */
> + err = mmc_sd_switch_hs(card);
> + if (err > 0)
> + mmc_sd_go_highspeed(card);
> + else if (err)
> + goto free_card;
> +
> + /*
> + * Set bus speed.
> + */
> + mmc_set_clock(host, mmc_sd_get_max_clock(card));
>
> - mmc_set_bus_width(host, MMC_BUS_WIDTH_4);
> + /*
> + * Switch to wider bus (if supported).
> + */
> + if ((host->caps & MMC_CAP_4_BIT_DATA) &&
> + (card->scr.bus_widths & SD_SCR_BUS_WIDTH_4)) {
> + err = mmc_app_set_bus_width(card, MMC_BUS_WIDTH_4);
> + if (err)
> + goto free_card;
> +
> + mmc_set_bus_width(host, MMC_BUS_WIDTH_4);
> + }
> }
>
> host->card = card;
> diff --git a/drivers/mmc/core/sd.h b/drivers/mmc/core/sd.h
> index 3d8800f..5106b44 100644
> --- a/drivers/mmc/core/sd.h
> +++ b/drivers/mmc/core/sd.h
> @@ -5,7 +5,8 @@
>
> extern struct device_type sd_type;
>
> -int mmc_sd_get_cid(struct mmc_host *host, u32 ocr, u32 *cid);
> +int mmc_sd_get_cid(struct mmc_host *host, u32 ocr, u32 *cid,
> + u32 *rocr);
> int mmc_sd_get_csd(struct mmc_host *host, struct mmc_card *card);
> void mmc_decode_cid(struct mmc_card *card);
> int mmc_sd_setup_card(struct mmc_host *host, struct mmc_card *card,
> diff --git a/drivers/mmc/core/sdio.c b/drivers/mmc/core/sdio.c
> index 1e60959..c4a6614 100644
> --- a/drivers/mmc/core/sdio.c
> +++ b/drivers/mmc/core/sdio.c
> @@ -370,7 +370,8 @@ static int mmc_sdio_init_card(struct mmc_host *host, u32 ocr,
> }
>
> if (ocr & R4_MEMORY_PRESENT
> - && mmc_sd_get_cid(host, host->ocr & ocr, card->raw_cid) == 0) {
> + && mmc_sd_get_cid(host, host->ocr & ocr, card->raw_cid,
> + NULL) == 0) {
> card->type = MMC_TYPE_SD_COMBO;
>
> if (oldcard && (oldcard->type != MMC_TYPE_SD_COMBO ||
> diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
> index 52faa50..9f38317 100644
> --- a/drivers/mmc/host/sdhci.c
> +++ b/drivers/mmc/host/sdhci.c
> @@ -61,7 +61,7 @@ static void sdhci_dumpregs(struct sdhci_host *host)
> sdhci_readw(host, SDHCI_TRANSFER_MODE));
> printk(KERN_DEBUG DRIVER_NAME ": Present: 0x%08x | Host ctl: 0x%08x\n",
> sdhci_readl(host, SDHCI_PRESENT_STATE),
> - sdhci_readb(host, SDHCI_HOST_CONTROL));
> + sdhci_readb(host, SDHCI_HOST_CONTROL1));
> printk(KERN_DEBUG DRIVER_NAME ": Power: 0x%08x | Blk gap: 0x%08x\n",
> sdhci_readb(host, SDHCI_POWER_CONTROL),
> sdhci_readb(host, SDHCI_BLOCK_GAP_CONTROL));
> @@ -220,18 +220,18 @@ static void sdhci_activate_led(struct sdhci_host *host)
> {
> u8 ctrl;
>
> - ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
> + ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL1);
> ctrl |= SDHCI_CTRL_LED;
> - sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
> + sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL1);
> }
>
> static void sdhci_deactivate_led(struct sdhci_host *host)
> {
> u8 ctrl;
>
> - ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
> + ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL1);
> ctrl &= ~SDHCI_CTRL_LED;
> - sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
> + sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL1);
> }
>
> #ifdef SDHCI_USE_LEDS_CLASS
> @@ -803,14 +803,14 @@ static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_command *cmd)
> * is ADMA.
> */
> if (host->version >= SDHCI_SPEC_200) {
> - ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
> + ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL1);
> ctrl &= ~SDHCI_CTRL_DMA_MASK;
> if ((host->flags & SDHCI_REQ_USE_DMA) &&
> (host->flags & SDHCI_USE_ADMA))
> ctrl |= SDHCI_CTRL_ADMA32;
> else
> ctrl |= SDHCI_CTRL_SDMA;
> - sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
> + sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL1);
> }
>
> if (!(host->flags & SDHCI_REQ_USE_DMA)) {
> @@ -1218,7 +1218,7 @@ static void sdhci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
> if (host->ops->platform_8bit_width)
> host->ops->platform_8bit_width(host, ios->bus_width);
> else {
> - ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
> + ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL1);
> if (ios->bus_width == MMC_BUS_WIDTH_8) {
> ctrl &= ~SDHCI_CTRL_4BITBUS;
> if (host->version >= SDHCI_SPEC_300)
> @@ -1231,10 +1231,10 @@ static void sdhci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
> else
> ctrl &= ~SDHCI_CTRL_4BITBUS;
> }
> - sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
> + sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL1);
> }
>
> - ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
> + ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL1);
>
> if ((ios->timing == MMC_TIMING_SD_HS ||
> ios->timing == MMC_TIMING_MMC_HS)
> @@ -1243,7 +1243,26 @@ static void sdhci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
> else
> ctrl &= ~SDHCI_CTRL_HISPD;
>
> - sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
> + sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL1);
> +
> + if (host->version >= SDHCI_SPEC_300) {
> + u16 ctrl_2;
> +
> + ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
> + if (!(ctrl_2 & SDHCI_CTRL_PRESET_VAL_ENABLE)) {
> + /*
> + * We only need to set Driver Strength if the
> + * preset value enable is not set.
> + */
> + ctrl_2 &= ~SDHCI_CTRL_DRV_TYPE_MASK;
> + if (ios->drv_type == MMC_SET_DRIVER_TYPE_A)
> + ctrl_2 |= SDHCI_CTRL_DRV_TYPE_A;
> + else if (ios->drv_type == MMC_SET_DRIVER_TYPE_C)
> + ctrl_2 |= SDHCI_CTRL_DRV_TYPE_C;
> +
> + sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
> + }
> + }
>
> /*
> * Some (ENE) controllers go apeshit on some ios operation,
> @@ -2087,6 +2106,14 @@ int sdhci_add_host(struct sdhci_host *host)
> if (caps[1] & SDHCI_SUPPORT_DDR50)
> mmc->caps |= MMC_CAP_UHS_DDR50;
>
> + /* Driver Type(s) (A, C, D) supported by the host */
> + if (caps[1] & SDHCI_DRIVER_TYPE_A)
> + mmc->caps |= MMC_CAP_DRIVER_TYPE_A;
> + if (caps[1] & SDHCI_DRIVER_TYPE_C)
> + mmc->caps |= MMC_CAP_DRIVER_TYPE_C;
> + if (caps[1] & SDHCI_DRIVER_TYPE_D)
> + mmc->caps |= MMC_CAP_DRIVER_TYPE_D;
> +
> ocr_avail = 0;
> /*
> * According to SD Host Controller spec v3.00, if the Host System
> diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h
> index 5cba2fe..04c41a4 100644
> --- a/drivers/mmc/host/sdhci.h
> +++ b/drivers/mmc/host/sdhci.h
> @@ -71,7 +71,7 @@
> #define SDHCI_DATA_LVL_MASK 0x00F00000
> #define SDHCI_DATA_LVL_SHIFT 20
>
> -#define SDHCI_HOST_CONTROL 0x28
> +#define SDHCI_HOST_CONTROL1 0x28
> #define SDHCI_CTRL_LED 0x01
> #define SDHCI_CTRL_4BITBUS 0x02
> #define SDHCI_CTRL_HISPD 0x04
> @@ -150,6 +150,12 @@
>
> #define SDHCI_HOST_CONTROL2 0x3E
> #define SDHCI_CTRL_VDD_180 0x0008
> +#define SDHCI_CTRL_DRV_TYPE_MASK 0x0030
> +#define SDHCI_CTRL_DRV_TYPE_B 0x0000
> +#define SDHCI_CTRL_DRV_TYPE_A 0x0010
> +#define SDHCI_CTRL_DRV_TYPE_C 0x0020
> +#define SDHCI_CTRL_DRV_TYPE_D 0x0030
> +#define SDHCI_CTRL_PRESET_VAL_ENABLE 0x8000
>
> #define SDHCI_CAPABILITIES 0x40
> #define SDHCI_TIMEOUT_CLK_MASK 0x0000003F
> @@ -173,6 +179,9 @@
> #define SDHCI_SUPPORT_SDR50 0x00000001
> #define SDHCI_SUPPORT_SDR104 0x00000002
> #define SDHCI_SUPPORT_DDR50 0x00000004
> +#define SDHCI_DRIVER_TYPE_A 0x00000010
> +#define SDHCI_DRIVER_TYPE_C 0x00000020
> +#define SDHCI_DRIVER_TYPE_D 0x00000040
>
> #define SDHCI_CAPABILITIES_1 0x44
>
> diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h
> index 56f4d92..5393272 100644
> --- a/include/linux/mmc/card.h
> +++ b/include/linux/mmc/card.h
> @@ -83,6 +83,10 @@ struct sd_switch_caps {
> unsigned int hs_max_dtr;
> unsigned int sd3_bus_mode;
> unsigned int sd3_drv_type;
> +#define SD_DRIVER_TYPE_B 0x01
> +#define SD_DRIVER_TYPE_A 0x02
> +#define SD_DRIVER_TYPE_C 0x04
> +#define SD_DRIVER_TYPE_D 0x08
> unsigned int sd3_curr_limit;
> };
>
> diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h
> index bde5a0b..949e4d5 100644
> --- a/include/linux/mmc/host.h
> +++ b/include/linux/mmc/host.h
> @@ -61,6 +61,13 @@ struct mmc_ios {
>
> #define MMC_SIGNAL_VOLTAGE_330 0
> #define MMC_SIGNAL_VOLTAGE_180 1
> +
> + unsigned char drv_type; /* driver type (A, B, C, D) */
> +
> +#define MMC_SET_DRIVER_TYPE_B 0
> +#define MMC_SET_DRIVER_TYPE_A 1
> +#define MMC_SET_DRIVER_TYPE_C 2
> +#define MMC_SET_DRIVER_TYPE_D 3
> };
>
> struct mmc_host_ops {
> @@ -188,6 +195,9 @@ struct mmc_host {
> #define MMC_CAP_SET_XPC_330 (1 << 20) /* Host supports >150mA current at 3.3V */
> #define MMC_CAP_SET_XPC_300 (1 << 21) /* Host supports >150mA current at 3.0V */
> #define MMC_CAP_SET_XPC_180 (1 << 22) /* Host supports >150mA current at 1.8V */
> +#define MMC_CAP_DRIVER_TYPE_A (1 << 23) /* Host supports Driver Type A */
> +#define MMC_CAP_DRIVER_TYPE_C (1 << 24) /* Host supports Driver Type C */
> +#define MMC_CAP_DRIVER_TYPE_D (1 << 25) /* Host supports Driver Type D */
>
> mmc_pm_flag_t pm_caps; /* supported pm features */
>
> --
> 1.7.1
>
>
next prev parent reply other threads:[~2011-05-06 10:37 UTC|newest]
Thread overview: 54+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-05-05 6:48 [PATCH v4 00/15] add support for host controller v3.00 Arindam Nath
2011-05-05 6:48 ` [PATCH v4 01/15] mmc: sd: add support for signal voltage switch procedure Arindam Nath
2011-05-06 10:36 ` zhangfei gao
2011-05-11 3:34 ` Chris Ball
2011-05-05 6:48 ` [PATCH v4 02/15] mmc: sd: query function modes for uhs cards Arindam Nath
2011-05-06 10:37 ` zhangfei gao
2011-05-11 3:34 ` Chris Ball
2011-05-05 6:48 ` [PATCH v4 03/15] mmc: sd: add support for driver type selection Arindam Nath
2011-05-06 10:37 ` zhangfei gao [this message]
2011-05-11 3:34 ` Chris Ball
2011-05-05 6:49 ` [PATCH v4 04/15] mmc: sdhci: reset sdclk before setting high speed enable Arindam Nath
2011-05-06 10:38 ` zhangfei gao
2011-05-11 3:36 ` Chris Ball
2011-05-05 6:49 ` [PATCH v4 05/15] mmc: sd: add support for uhs bus speed mode selection Arindam Nath
2011-05-06 10:41 ` zhangfei gao
2011-05-11 3:36 ` Chris Ball
2011-05-05 6:49 ` [PATCH v4 06/15] mmc: sd: set current limit for uhs cards Arindam Nath
2011-05-06 10:38 ` zhangfei gao
2011-05-11 3:37 ` Chris Ball
2011-05-05 6:49 ` [PATCH v4 07/15] mmc: sd: report correct speed and capacity of " Arindam Nath
2011-05-06 10:39 ` zhangfei gao
2011-05-11 3:37 ` Chris Ball
2011-05-05 6:49 ` [PATCH v4 08/15] mmc: sd: add support for tuning during uhs initialization Arindam Nath
2011-05-06 10:39 ` zhangfei gao
2011-05-11 3:38 ` Chris Ball
2011-05-05 6:49 ` [PATCH v4 09/15] mmc: sdhci: enable preset value after " Arindam Nath
2011-05-06 10:40 ` zhangfei gao
2011-05-11 3:38 ` Chris Ball
2011-05-05 6:49 ` [PATCH v4 10/15] mmc: sdhci: add support for programmable clock mode Arindam Nath
2011-05-06 10:40 ` zhangfei gao
2011-05-11 3:39 ` Chris Ball
2011-05-05 6:49 ` [PATCH v4 11/15] mmc: sdhci: add support for retuning mode 1 Arindam Nath
2011-05-06 10:40 ` zhangfei gao
2011-05-11 3:39 ` Chris Ball
2011-05-05 6:49 ` [PATCH v4 12/15] sdhci pxa add platform specific code for UHS signaling Arindam Nath
2011-05-11 1:54 ` Chris Ball
2011-05-11 8:48 ` zhangfei gao
2011-05-11 8:52 ` Philip Rakity
2011-05-11 9:28 ` zhangfei gao
2011-05-11 9:47 ` Philip Rakity
2011-05-12 1:53 ` Philip Rakity
2011-05-13 8:03 ` zhangfei gao
2011-05-15 21:42 ` Philip Rakity
2011-05-16 5:57 ` zhangfei gao
2011-05-05 6:49 ` [PATCH v4 13/15] mmc eMMC signal voltage does not use CMD11 Arindam Nath
2011-05-11 1:51 ` Chris Ball
2011-05-11 9:19 ` zhangfei gao
2011-05-11 15:01 ` Philip Rakity
2011-05-12 1:53 ` Philip Rakity
2011-05-05 6:49 ` [PATCH v4 14/15] sdhci add hooks for UHS setting by platform specific code Arindam Nath
2011-05-05 6:49 ` [PATCH v4 15/15] mmc add support for eMMC Dual Data Rate Arindam Nath
2011-05-05 8:18 ` [PATCH v4 00/15] add support for host controller v3.00 Nath, Arindam
2011-05-11 3:43 ` Chris Ball
2011-05-11 6:13 ` Nath, Arindam
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=BANLkTik-WnPx-ssEE+aFdBYj86YbBD3Wtw@mail.gmail.com \
--to=zhangfei.gao@gmail.com \
--cc=aaron.lu@amd.com \
--cc=anath.amd@gmail.com \
--cc=arindam.nath@amd.com \
--cc=cjb@laptop.org \
--cc=henry.su@amd.com \
--cc=linux-mmc@vger.kernel.org \
--cc=prakity@marvell.com \
--cc=subhashj@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).