From: Russell King <rmk+kernel@arm.linux.org.uk>
To: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>,
linux-mmc@vger.kernel.org, Marcin Wojtas <mw@semihalf.com>,
Shawn Guo <shawnguo@kernel.org>,
Sascha Hauer <kernel@pengutronix.de>
Subject: [PATCH v4 10/25] mmc: sdhci: clean up coding style in sdhci_adma_table_pre()
Date: Fri, 29 Jan 2016 09:44:37 +0000 [thread overview]
Message-ID: <E1aP5bZ-0001pV-3t@rmk-PC.arm.linux.org.uk> (raw)
In-Reply-To: <20160129094324.GA20025@n2100.arm.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
---
drivers/mmc/host/sdhci.c | 29 +++++++++--------------------
1 file changed, 9 insertions(+), 20 deletions(-)
diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
index c63d35c0f84b..774b0cf05f9d 100644
--- a/drivers/mmc/host/sdhci.c
+++ b/drivers/mmc/host/sdhci.c
@@ -465,16 +465,12 @@ static void sdhci_adma_mark_end(void *desc)
static int sdhci_adma_table_pre(struct sdhci_host *host,
struct mmc_data *data)
{
- void *desc;
- void *align;
- dma_addr_t addr;
- dma_addr_t align_addr;
- int len, offset;
-
struct scatterlist *sg;
- int i;
- char *buffer;
unsigned long flags;
+ dma_addr_t addr, align_addr;
+ void *desc, *align;
+ char *buffer;
+ int len, offset, i;
/*
* The spec does not specify endianness of descriptor table.
@@ -495,10 +491,9 @@ static int sdhci_adma_table_pre(struct sdhci_host *host,
len = sg_dma_len(sg);
/*
- * The SDHCI specification states that ADMA
- * addresses must be 32-bit aligned. If they
- * aren't, then we use a bounce buffer for
- * the (up to three) bytes that screw up the
+ * The SDHCI specification states that ADMA addresses must
+ * be 32-bit aligned. If they aren't, then we use a bounce
+ * buffer for the (up to three) bytes that screw up the
* alignment.
*/
offset = (SDHCI_ADMA2_ALIGN - (addr & SDHCI_ADMA2_MASK)) &
@@ -542,19 +537,13 @@ static int sdhci_adma_table_pre(struct sdhci_host *host,
}
if (host->quirks & SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC) {
- /*
- * Mark the last descriptor as the terminating descriptor
- */
+ /* Mark the last descriptor as the terminating descriptor */
if (desc != host->adma_table) {
desc -= host->desc_sz;
sdhci_adma_mark_end(desc);
}
} else {
- /*
- * Add a terminating entry.
- */
-
- /* nop, end, valid */
+ /* Add a terminating entry - nop, end, valid */
sdhci_adma_write_desc(host, desc, 0, 0, ADMA2_NOP_END_VALID);
}
return 0;
--
2.1.0
next prev parent reply other threads:[~2016-01-29 9:44 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-01-29 9:43 [PATCH v4 00/25] MMC/SDHCI fixes Russell King - ARM Linux
2016-01-29 9:43 ` [PATCH v4 01/25] mmc: core: shut up "voltage-ranges unspecified" pr_info() Russell King
2016-01-29 9:43 ` [PATCH v4 02/25] mmc: core: improve mmc_of_parse_voltage() to return better status Russell King
2016-01-29 9:44 ` [PATCH v4 03/25] mmc: block: shut up "retrying because a re-tune was needed" message Russell King
2016-01-29 9:44 ` [PATCH v4 04/25] mmc: core: report tuning command execution failure reason Russell King
2016-01-29 9:44 ` [PATCH v4 05/25] mmc: sdhci: move initialisation of command error member Russell King
2016-01-29 9:44 ` [PATCH v4 06/25] mmc: sdhci: clean up command error handling Russell King
2016-01-29 9:44 ` [PATCH v4 07/25] mmc: sdhci: command response CRC " Russell King
2016-01-29 9:44 ` [PATCH v4 08/25] mmc: sdhci: avoid unnecessary mapping/unmapping of align buffer Russell King
2016-01-29 9:44 ` [PATCH v4 09/25] mmc: sdhci: allocate alignment and DMA descriptor buffer together Russell King
2016-01-29 9:44 ` Russell King [this message]
2016-01-29 9:44 ` [PATCH v4 11/25] mmc: sdhci: avoid walking SG list for writes Russell King
2016-01-29 9:44 ` [PATCH v4 12/25] mmc: sdhci: factor out common DMA cleanup in sdhci_finish_data() Russell King
2016-01-29 9:44 ` [PATCH v4 13/25] mmc: sdhci: move sdhci_pre_dma_transfer() Russell King
2016-01-29 9:44 ` [PATCH v4 14/25] mmc: sdhci: factor out sdhci_pre_dma_transfer() from sdhci_adma_table_pre() Russell King
2016-01-29 9:45 ` [PATCH v4 15/25] mmc: sdhci: pass the cookie into sdhci_pre_dma_transfer() Russell King
2016-01-29 9:45 ` [PATCH v4 16/25] mmc: sdhci: always unmap a mapped data transfer in sdhci_post_req() Russell King
2016-01-29 9:45 ` [PATCH v4 17/25] mmc: sdhci: clean up host cookie handling Russell King
2016-01-29 9:45 ` [PATCH v4 18/25] mmc: sdhci: plug DMA mapping leak on error Russell King
2016-01-29 9:45 ` [PATCH v4 19/25] mmc: sdhci-pxav3: fix higher speed mode capabilities Russell King
2016-01-29 9:45 ` [PATCH v4 20/25] mmc: sdhci: further fix for DMA unmapping in sdhci_post_req() Russell King
2016-01-29 9:45 ` [PATCH v4 21/25] mmc: sdhci: fix data timeout (part 1) Russell King
2016-01-29 9:45 ` [PATCH v4 22/25] mmc: sdhci: fix data timeout (part 2) Russell King
2016-01-29 9:45 ` [PATCH v4 23/25] mmc: sdhci: prepare DMA address/size quirk handling consolidation Russell King
2016-01-29 9:45 ` [PATCH v4 24/25] mmc: sdhci: consolidate the DMA/ADMA size/address quicks Russell King
2016-01-29 9:45 ` [PATCH v4 25/25] mmc: sdhci: further code simplication Russell King
2016-02-04 10:55 ` [PATCH v4 00/25] MMC/SDHCI fixes Ulf Hansson
2016-02-12 9:49 ` Adrian Hunter
2016-02-12 14:23 ` Gregory CLEMENT
2016-02-16 13:08 ` Ulf Hansson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=E1aP5bZ-0001pV-3t@rmk-PC.arm.linux.org.uk \
--to=rmk+kernel@arm.linux.org.uk \
--cc=gregory.clement@free-electrons.com \
--cc=kernel@pengutronix.de \
--cc=linux-mmc@vger.kernel.org \
--cc=mw@semihalf.com \
--cc=shawnguo@kernel.org \
--cc=ulf.hansson@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox