Linux MultiMedia Card development
 help / color / mirror / Atom feed
From: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
To: Biju Das <biju.das.jz@bp.renesas.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>,
	Wolfram Sang <wsa+renesas@sang-engineering.com>,
	linux-mmc@vger.kernel.org, linux-renesas-soc@vger.kernel.org,
	Geert Uytterhoeven <geert+renesas@glider.be>,
	Prabhakar Mahadev Lad <prabhakar.mahadev-lad.rj@bp.renesas.com>,
	Biju Das <biju.das.au@gmail.com>
Subject: Re: [PATCH 4/7] mmc: renesas_sdhi: Add support for RZ/G3E SoC
Date: Sun, 26 Jan 2025 20:00:45 +0100	[thread overview]
Message-ID: <Z5aGXVEzGt8pVFBl@tom-desktop> (raw)
In-Reply-To: <20250126134616.37334-5-biju.das.jz@bp.renesas.com>

On Sun, Jan 26, 2025 at 01:46:06PM +0000, Biju Das wrote:
> The SDHI/eMMC IPs in the RZ/G3E SoC are similar to those in R-Car Gen3.
> However, the RZ/G3E SD0 channel has Voltage level control and PWEN pin
> support via SD_STATUS register.
> 
> internal regulator support is added to control the voltage levels of
> the SD pins via sd_iovs/sd_pwen bits in SD_STATUS register by populating
> vqmmc-regulator child node.
> 
> SD1 and SD2 channels have gpio regulator support and internal regulator
> support. Selection of the regulator is based on the regulator phandle.
> 
> Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
> ---
>  drivers/mmc/host/renesas_sdhi.h      |   1 +
>  drivers/mmc/host/renesas_sdhi_core.c | 129 +++++++++++++++++++++++++++
>  drivers/mmc/host/tmio_mmc.h          |   5 ++
>  3 files changed, 135 insertions(+)
> 
> diff --git a/drivers/mmc/host/renesas_sdhi.h b/drivers/mmc/host/renesas_sdhi.h
> index f12a87442338..291ddb4ad9be 100644
> --- a/drivers/mmc/host/renesas_sdhi.h
> +++ b/drivers/mmc/host/renesas_sdhi.h
> @@ -95,6 +95,7 @@ struct renesas_sdhi {
>  
>  	struct reset_control *rstc;
>  	struct tmio_mmc_host *host;
> +	struct regulator_dev *rdev;
>  };
>  
>  #define host_to_priv(host) \
> diff --git a/drivers/mmc/host/renesas_sdhi_core.c b/drivers/mmc/host/renesas_sdhi_core.c
> index 6ea651409774..bbfa68ca682b 100644
> --- a/drivers/mmc/host/renesas_sdhi_core.c
> +++ b/drivers/mmc/host/renesas_sdhi_core.c
> @@ -32,6 +32,8 @@
>  #include <linux/platform_device.h>
>  #include <linux/pm_domain.h>
>  #include <linux/regulator/consumer.h>
> +#include <linux/regulator/driver.h>
> +#include <linux/regulator/of_regulator.h>
>  #include <linux/reset.h>
>  #include <linux/sh_dma.h>
>  #include <linux/slab.h>
> @@ -581,12 +583,24 @@ static void renesas_sdhi_reset(struct tmio_mmc_host *host, bool preserve)
>  
>  	if (!preserve) {
>  		if (priv->rstc) {
> +			u32 sd_status;
> +			/*
> +			 * HW reset might have toggled the regulator state in
> +			 * HW which regulator core might be unaware of so save
> +			 * and restore the regulator state during HW reset.
> +			 */
> +			if (priv->rdev)
> +				sd_ctrl_read32_rep(host, CTL_SD_STATUS, &sd_status, 1);
> +
>  			reset_control_reset(priv->rstc);
>  			/* Unknown why but without polling reset status, it will hang */
>  			read_poll_timeout(reset_control_status, ret, ret == 0, 1, 100,
>  					  false, priv->rstc);
>  			/* At least SDHI_VER_GEN2_SDR50 needs manual release of reset */
>  			sd_ctrl_write16(host, CTL_RESET_SD, 0x0001);
> +			if (priv->rdev)
> +				sd_ctrl_write32(host, CTL_SD_STATUS, sd_status);
> +
>  			priv->needs_adjust_hs400 = false;
>  			renesas_sdhi_set_clock(host, host->clk_cache);
>  
> @@ -904,15 +918,113 @@ static void renesas_sdhi_enable_dma(struct tmio_mmc_host *host, bool enable)
>  	renesas_sdhi_sdbuf_width(host, enable ? width : 16);
>  }
>  
> +static const unsigned int renesas_sdhi_vqmmc_voltages[] = {
> +	3300000, 1800000
> +};
> +
> +static int renesas_sdhi_regulator_disable(struct regulator_dev *rdev)
> +{
> +	struct tmio_mmc_host *host = rdev_get_drvdata(rdev);
> +	u32 sd_status;
> +
> +	sd_ctrl_read32_rep(host, CTL_SD_STATUS, &sd_status, 1);
> +	sd_status &= ~SD_STATUS_PWEN;
> +	sd_ctrl_write32(host, CTL_SD_STATUS, sd_status);
> +
> +	return 0;
> +}
> +
> +static int renesas_sdhi_regulator_enable(struct regulator_dev *rdev)
> +{
> +	struct tmio_mmc_host *host = rdev_get_drvdata(rdev);
> +	u32 sd_status;
> +
> +	sd_ctrl_read32_rep(host, CTL_SD_STATUS, &sd_status, 1);
> +	sd_status |= SD_STATUS_PWEN;
> +	sd_ctrl_write32(host, CTL_SD_STATUS, sd_status);
> +
> +	return 0;
> +}
> +
> +static int renesas_sdhi_regulator_is_enabled(struct regulator_dev *rdev)
> +{
> +	struct tmio_mmc_host *host = rdev_get_drvdata(rdev);
> +	u32 sd_status;
> +
> +	sd_ctrl_read32_rep(host, CTL_SD_STATUS, &sd_status, 1);
> +
> +	return (sd_status & SD_STATUS_PWEN) ? 1 : 0;
> +}
> +
> +static int renesas_sdhi_regulator_get_voltage(struct regulator_dev *rdev)
> +{
> +	struct tmio_mmc_host *host = rdev_get_drvdata(rdev);
> +	u32 sd_status;
> +
> +	sd_ctrl_read32_rep(host, CTL_SD_STATUS, &sd_status, 1);
> +
> +	return (sd_status & SD_STATUS_IOVS) ? 1800000 : 3300000;
> +}
> +
> +static int renesas_sdhi_regulator_set_voltage(struct regulator_dev *rdev,
> +					      int min_uV, int max_uV,
> +					      unsigned int *selector)
> +{
> +	struct tmio_mmc_host *host = rdev_get_drvdata(rdev);
> +	u32 sd_status;
> +
> +	sd_ctrl_read32_rep(host, CTL_SD_STATUS, &sd_status, 1);
> +	if (min_uV >= 1700000 && max_uV <= 1950000) {
> +		sd_status |= SD_STATUS_IOVS;
> +		*selector = 1;
> +	} else {
> +		sd_status &= ~SD_STATUS_IOVS;
> +		*selector = 0;
> +	}
> +	sd_ctrl_write32(host, CTL_SD_STATUS, sd_status);
> +
> +	return 0;
> +}
> +
> +static int renesas_sdhi_regulator_list_voltage(struct regulator_dev *rdev,
> +					       unsigned int selector)
> +{
> +	if (selector >= ARRAY_SIZE(renesas_sdhi_vqmmc_voltages))
> +		return -EINVAL;
> +
> +	return renesas_sdhi_vqmmc_voltages[selector];
> +}
> +
> +static const struct regulator_ops renesas_sdhi_regulator_voltage_ops = {
> +	.enable = renesas_sdhi_regulator_enable,
> +	.disable = renesas_sdhi_regulator_disable,
> +	.is_enabled = renesas_sdhi_regulator_is_enabled,
> +	.list_voltage = renesas_sdhi_regulator_list_voltage,
> +	.get_voltage = renesas_sdhi_regulator_get_voltage,
> +	.set_voltage = renesas_sdhi_regulator_set_voltage,
> +};
> +
> +static struct regulator_desc renesas_sdhi_vqmmc_regulator = {
> +	.of_match	= of_match_ptr("vqmmc-regulator"),
> +	.owner		= THIS_MODULE,
> +	.type		= REGULATOR_VOLTAGE,
> +	.ops		= &renesas_sdhi_regulator_voltage_ops,
> +	.volt_table	= renesas_sdhi_vqmmc_voltages,
> +	.n_voltages	= ARRAY_SIZE(renesas_sdhi_vqmmc_voltages),
> +};
> +
>  int renesas_sdhi_probe(struct platform_device *pdev,
>  		       const struct tmio_mmc_dma_ops *dma_ops,
>  		       const struct renesas_sdhi_of_data *of_data,
>  		       const struct renesas_sdhi_quirks *quirks)
>  {
> +	struct regulator_config rcfg = { .dev = &pdev->dev, };
>  	struct tmio_mmc_data *mmd = pdev->dev.platform_data;
>  	struct renesas_sdhi_dma *dma_priv;
> +	struct device *dev = &pdev->dev;
>  	struct tmio_mmc_data *mmc_data;
>  	struct tmio_mmc_host *host;
> +	struct regulator_dev *rdev;
>  	struct renesas_sdhi *priv;
>  	int num_irqs, irq, ret, i;
>  	struct resource *res;
> @@ -1053,6 +1165,23 @@ int renesas_sdhi_probe(struct platform_device *pdev,
>  	if (ret)
>  		goto efree;
>  
> +	rcfg.of_node = of_get_child_by_name(dev->of_node, "vqmmc-regulator");
> +	if (rcfg.of_node) {
> +		rcfg.driver_data = priv->host;
> +
> +		renesas_sdhi_vqmmc_regulator.name = "sdhi-vqmmc-regulator";
> +		renesas_sdhi_vqmmc_regulator.of_match = of_match_ptr("vqmmc-regulator");
> +		renesas_sdhi_vqmmc_regulator.type = REGULATOR_VOLTAGE;
> +		renesas_sdhi_vqmmc_regulator.owner = THIS_MODULE;
> +		rdev = devm_regulator_register(dev, &renesas_sdhi_vqmmc_regulator, &rcfg);
> +		of_node_put(rcfg.of_node);
> +		if (IS_ERR(rdev)) {
> +			dev_err(dev, "regulator register failed err=%ld", PTR_ERR(rdev));
> +			goto efree;
> +		}
> +		priv->rdev = rdev;
> +	}
> +
>  	ver = sd_ctrl_read16(host, CTL_VERSION);
>  	/* GEN2_SDR104 is first known SDHI to use 32bit block count */
>  	if (ver < SDHI_VER_GEN2_SDR104 && mmc_data->max_blk_count > U16_MAX)
> diff --git a/drivers/mmc/host/tmio_mmc.h b/drivers/mmc/host/tmio_mmc.h
> index a75755f31d31..5970ca598850 100644
> --- a/drivers/mmc/host/tmio_mmc.h
> +++ b/drivers/mmc/host/tmio_mmc.h
> @@ -44,6 +44,7 @@
>  #define CTL_RESET_SD 0xe0
>  #define CTL_VERSION 0xe2
>  #define CTL_SDIF_MODE 0xe6 /* only known on R-Car 2+ */
> +#define CTL_SD_STATUS 0xf2 /* only known on RZ/{G2L,G3E,V2H} */
>  
>  /* Definitions for values the CTL_STOP_INTERNAL_ACTION register can take */
>  #define TMIO_STOP_STP		BIT(0)
> @@ -103,6 +104,10 @@
>  /* Definitions for values the CTL_SDIF_MODE register can take */
>  #define SDIF_MODE_HS400		BIT(0) /* only known on R-Car 2+ */
>  
> +/* Definitions for values the CTL_SD_STATUS register can take */
> +#define SD_STATUS_PWEN		BIT(0) /* only known on RZ/{G3E,V2H} */
> +#define SD_STATUS_IOVS		BIT(16) /* only known on RZ/{G3E,V2H} */
> +
>  /* Define some IRQ masks */
>  /* This is the mask used at reset by the chip */
>  #define TMIO_MASK_ALL           0x837f031d
> -- 
> 2.43.0
>

Reviewed-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>

  reply	other threads:[~2025-01-26 19:00 UTC|newest]

Thread overview: 16+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2025-01-26 13:46 [PATCH 0/7] Add RZ/G3E SDHI support Biju Das
2025-01-26 13:46 ` [PATCH 1/7] dt-bindings: mmc: renesas,sdhi: Document RZ/G3E support Biju Das
2025-01-26 18:57   ` Tommaso Merciai
2025-01-27 19:16   ` Rob Herring
2025-01-28  8:56     ` Biju Das
2025-01-28 11:15   ` Geert Uytterhoeven
2025-01-28 12:41     ` Biju Das
2025-01-26 13:46 ` [PATCH 3/7] mmc: renesas_sdhi: Arrange local variables in reverse xmas tree order Biju Das
2025-01-26 19:00   ` Tommaso Merciai
2025-01-28 11:14   ` Geert Uytterhoeven
2025-01-26 13:46 ` [PATCH 4/7] mmc: renesas_sdhi: Add support for RZ/G3E SoC Biju Das
2025-01-26 19:00   ` Tommaso Merciai [this message]
2025-01-28 13:32   ` Geert Uytterhoeven
2025-01-28 13:43     ` Biju Das
2025-01-29 14:45       ` Biju Das
2025-01-29 14:47         ` Geert Uytterhoeven

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=Z5aGXVEzGt8pVFBl@tom-desktop \
    --to=tommaso.merciai.xr@bp.renesas.com \
    --cc=biju.das.au@gmail.com \
    --cc=biju.das.jz@bp.renesas.com \
    --cc=geert+renesas@glider.be \
    --cc=linux-mmc@vger.kernel.org \
    --cc=linux-renesas-soc@vger.kernel.org \
    --cc=prabhakar.mahadev-lad.rj@bp.renesas.com \
    --cc=ulf.hansson@linaro.org \
    --cc=wsa+renesas@sang-engineering.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox