* the at91 mci controller does not recognized my libertas 8686 sdio wifi chip after a reset
@ 2010-03-21 10:27 David MOUSSAUD
0 siblings, 0 replies; 2+ messages in thread
From: David MOUSSAUD @ 2010-03-21 10:27 UTC (permalink / raw)
To: linux-mmc, libertas-dev
Hello,
I'm writting to the both mmc & libertas mailing list because i might
think the problem is related.
I'm using a prototype board running a AT91sam9g20 processor. I have a
libertas sdio wifi chip connected to my MCI controller.
I've applied the 2.6.32 bsp patch.
When I power up the board (power on reset), the sdio chip is well
probed by the mci controller.
But when i reset the board, the mmc_rescan function failed because the call to
/*
* First we search for SDIO...
*/
err = mmc_send_io_op_cond(host, 0, &ocr);
return 110;
so my sdio chip is not recognized by my kernel.
I've tried to apply that patch "sdio : recognize io card without
powercycle" ( 516a82422209e078345d0ca54b16793d7bfd4782 ) without success.
Here is a dump of the mmc dialogue when the board is only reseted :
[ 1.160000] mmc0: starting CMD52 arg 00000c00 flags 00000195
[ 1.160000] Sending command 52 as 00001874, arg = 00000C00,
blocks = 0, length = 0 (MR = 00009B7C)
[ 1.160000] MCI irq: status = 0000C0E5, C07F0001, 00000001
[ 1.160000] Command ready
[ 1.160000] Completed command
[ 1.160000] Status = 00000001/0000c0e5 [00001000 00000000
00000000 00000000]
[ 1.160000] mmc0: req done (CMD52): 0: 00001000 00000000 00000000 00000000
[ 1.160000] mmc0: starting CMD52 arg 80000c08 flags 00000195
[ 1.160000] Sending command 52 as 00001874, arg = 80000C08,
blocks = 0, length = 0 (MR = 00009B7C)
[ 1.160000] MCI irq: status = 0000C0E5, C07F0001, 00000001
[ 1.160000] Command ready
[ 1.160000] Completed command
[ 1.160000] Status = 00000001/0000c0e5 [00001008 00000000
00000000 00000000]
[ 1.160000] mmc0: req done (CMD52): 0: 00001008 00000000 00000000 00000000
[ 1.160000] mmc0: clock 400000Hz busmode 1 powermode 2 cs 1 Vdd
21 width 0 timing 0
[ 1.160000] clkdiv = 124. mcck = 397312
[ 1.160000] MMC: Setting controller bus width to 1
[ 1.160000] mmc0: starting CMD0 arg 00000000 flags 000000c0
[ 1.160000] Sending command 0 as 00000800, arg = 00000000,
blocks = 0, length = 0 (MR = 00009B7C)
[ 1.160000] MCI irq: status = 0000C0E5, C07F0001, 00000001
[ 1.160000] Command ready
[ 1.160000] Completed command
[ 1.160000] Status = 00000001/0000c0e5 [00001008 00000000
00000000 00000000]
[ 1.160000] mmc0: req done (CMD0): 0: 00001008 00000000 00000000 00000000
[ 1.160000] mmc0: clock 400000Hz busmode 1 powermode 2 cs 0 Vdd
21 width 0 timing 0
[ 1.160000] clkdiv = 124. mcck = 397312
[ 1.160000] MMC: Setting controller bus width to 1
[ 1.160000] mmc0: starting CMD8 arg 000001aa flags 000002f5
[ 1.160000] Sending command 8 as 00001848, arg = 000001AA,
blocks = 0, length = 0 (MR = 00009B7C)
[ 1.160000] MCI irq: status = 0010C0E4, C07F0001, 00100000
[ 1.160000] MMC: Response timeout
[ 1.160000] Completed command
[ 1.160000] Status = 00100000/0010c0e5 [00001008 00000000
00000000 00000000]
[ 1.160000] Error detected and set to -110/0 (cmd = 8, retries = 0)
[ 1.160000] mmc0: req done (CMD8): -110: 00001008 00000000
00000000 00000000
[ 1.160000] mmc0: starting CMD5 arg 00000000 flags 000002e1
[ 1.160000] Sending command 5 as 00001845, arg = 00000000,
blocks = 0, length = 0 (MR = 00009B7C)
[ 1.160000] MCI irq: status = 0010C0E4, C07F0001, 00100000
[ 1.160000] MMC: Response timeout
[ 1.160000] Completed command
[ 1.160000] Status = 00100000/0010c0e5 [00001008 00000000
00000000 00000000]
[ 1.160000] Error detected and set to -110/0 (cmd = 5, retries = 3)
[ 1.160000] mmc0: req failed (CMD5): -110, retrying...
[ 1.160000] Sending command 5 as 00001845, arg = 00000000,
blocks = 0, length = 0 (MR = 00009B7C)
[ 1.170000] MCI irq: status = 0010C0E4, C07F0001, 00100000
[ 1.170000] MMC: Response timeout
[ 1.170000] Completed command
[ 1.170000] Status = 00100000/0010c0e5 [00001008 00000000
00000000 00000000]
[ 1.170000] Error detected and set to -110/0 (cmd = 5, retries = 2)
[ 1.170000] mmc0: req failed (CMD5): -110, retrying...
[ 1.170000] Sending command 5 as 00001845, arg = 00000000,
blocks = 0, length = 0 (MR = 00009B7C)
[ 1.170000] MCI irq: status = 0010C0E4, C07F0001, 00100000
[ 1.170000] MMC: Response timeout
[ 1.170000] Completed command
[ 1.170000] Status = 00100000/0010c0e5 [00001008 00000000
00000000 00000000]
[ 1.170000] Error detected and set to -110/0 (cmd = 5, retries = 1)
[ 1.170000] mmc0: req failed (CMD5): -110, retrying...
[ 1.170000] Sending command 5 as 00001845, arg = 00000000,
blocks = 0, length = 0 (MR = 00009B7C)
[ 1.170000] MCI irq: status = 0010C0E4, C07F0001, 00100000
[ 1.170000] MMC: Response timeout
[ 1.170000] Completed command
[ 1.170000] Status = 00100000/0010c0e5 [00001008 00000000
00000000 00000000]
[ 1.170000] Error detected and set to -110/0 (cmd = 5, retries = 0)
[ 1.170000] mmc0: req done (CMD5): -110: 00001008 00000000
00000000 00000000
[ 1.170000] mmc0: starting CMD55 arg 00000000 flags 000000f5
[ 1.170000] Sending command 55 as 00001877, arg = 00000000,
blocks = 0, length = 0 (MR = 00009B7C)
[ 1.180000] MCI irq: status = 0010C0E4, C07F0001, 00100000
[ 1.180000] MMC: Response timeout
[ 1.180000] Completed command
[ 1.180000] Status = 00100000/0010c0e5 [00001008 00000000
00000000 00000000]
[ 1.180000] Error detected and set to -110/0 (cmd = 55, retries = 0)
[ 1.180000] mmc0: req done (CMD55): -110: 00001008 00000000
00000000 00000000
[ 1.180000] mmc0: starting CMD55 arg 00000000 flags 000000f5
[ 1.180000] Sending command 55 as 00001877, arg = 00000000,
blocks = 0, length = 0 (MR = 00009B7C)
[ 1.180000] MCI irq: status = 0010C0E4, C07F0001, 00100000
[ 1.180000] MMC: Response timeout
[ 1.180000] Completed command
[ 1.180000] Status = 00100000/0010c0e5 [00001008 00000000
00000000 00000000]
[ 1.180000] Error detected and set to -110/0 (cmd = 55, retries = 0)
[ 1.180000] mmc0: req done (CMD55): -110: 00001008 00000000
00000000 00000000
[ 1.180000] mmc0: starting CMD55 arg 00000000 flags 000000f5
[ 1.180000] Sending command 55 as 00001877, arg = 00000000,
blocks = 0, length = 0 (MR = 00009B7C)
[ 1.180000] MCI irq: status = 0010C0E4, C07F0001, 00100000
[ 1.180000] MMC: Response timeout
[ 1.180000] Completed command
[ 1.180000] Status = 00100000/0010c0e5 [00001008 00000000
00000000 00000000]
[ 1.180000] Error detected and set to -110/0 (cmd = 55, retries = 0)
[ 1.180000] mmc0: req done (CMD55): -110: 00001008 00000000
00000000 00000000
[ 1.180000] mmc0: starting CMD55 arg 00000000 flags 000000f5
[ 1.180000] Sending command 55 as 00001877, arg = 00000000,
blocks = 0, length = 0 (MR = 00009B7C)
[ 1.180000] MCI irq: status = 0010C0E4, C07F0001, 00100000
[ 1.180000] MMC: Response timeout
[ 1.180000] Completed command
[ 1.180000] Status = 00100000/0010c0e5 [00001008 00000000
00000000 00000000]
[ 1.180000] Error detected and set to -110/0 (cmd = 55, retries = 0)
[ 1.180000] mmc0: req done (CMD55): -110: 00001008 00000000
00000000 00000000
[ 1.180000] mmc0: starting CMD1 arg 00000000 flags 000000e1
[ 1.180000] Clearing timeout
[ 1.180000] Clearing: SR = 0000C0E4
[ 1.180000] Clearing: SR = 0000C0E4
[ 1.180000] Clearing: SR = 0000C0E4
[ 1.180000] Clearing: SR = 0000C0E4
[ 1.180000] Sending command 1 as 00001841, arg = 00000000,
blocks = 0, length = 0 (MR = 00009B7C)
[ 1.180000] MCI irq: status = 0010C0E4, C07F0001, 00100000
[ 1.180000] MMC: Response timeout
[ 1.180000] Completed command
[ 1.180000] Status = 00100000/0010c0e5 [00001008 00000000
00000000 00000000]
[ 1.180000] Error detected and set to -110/0 (cmd = 1, retries = 0)
[ 1.180000] mmc0: req done (CMD1): -110: 00001008 00000000
00000000 00000000
[ 1.180000] mmc0: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0
width 0 timing 0
[ 1.180000] MMC: Setting controller bus width to 1
Thanks in advance for any tips,
Regards,
D.MOUSSAUD.
^ permalink raw reply [flat|nested] 2+ messages in thread
* the at91 mci controller does not recognized my libertas 8686 sdio wifi chip after a reset
@ 2010-03-22 19:15 David MOUSSAUD
0 siblings, 0 replies; 2+ messages in thread
From: David MOUSSAUD @ 2010-03-22 19:15 UTC (permalink / raw)
To: linux-mmc
Hello,
I'm using a prototype board running a AT91sam9g20 processor. I have a
libertas sdio wifi chip connected to my MCI controller.
I've applied the 2.6.32 bsp patch.
When I power up the board (power on reset), the sdio chip is well
probed by the mci controller.
But when i reset the board, the mmc_rescan function failed because the call to
/*
* First we search for SDIO...
*/
err = mmc_send_io_op_cond(host, 0, &ocr);
return 110;
so my sdio chip is not recognized by my kernel.
I've tried to apply that patch "sdio : recognize io card without
powercycle" ( 516a82422209e078345d0ca54b16793d7bfd4782 ) without success.
Here is a dump of the mmc dialogue when the board is only reseted :
[ 1.160000] mmc0: starting CMD52 arg 00000c00 flags 00000195
[ 1.160000] Sending command 52 as 00001874, arg = 00000C00,
blocks = 0, length = 0 (MR = 00009B7C)
[ 1.160000] MCI irq: status = 0000C0E5, C07F0001, 00000001
[ 1.160000] Command ready
[ 1.160000] Completed command
[ 1.160000] Status = 00000001/0000c0e5 [00001000 00000000
00000000 00000000]
[ 1.160000] mmc0: req done (CMD52): 0: 00001000 00000000 00000000 00000000
[ 1.160000] mmc0: starting CMD52 arg 80000c08 flags 00000195
[ 1.160000] Sending command 52 as 00001874, arg = 80000C08,
blocks = 0, length = 0 (MR = 00009B7C)
[ 1.160000] MCI irq: status = 0000C0E5, C07F0001, 00000001
[ 1.160000] Command ready
[ 1.160000] Completed command
[ 1.160000] Status = 00000001/0000c0e5 [00001008 00000000
00000000 00000000]
[ 1.160000] mmc0: req done (CMD52): 0: 00001008 00000000 00000000 00000000
[ 1.160000] mmc0: clock 400000Hz busmode 1 powermode 2 cs 1 Vdd
21 width 0 timing 0
[ 1.160000] clkdiv = 124. mcck = 397312
[ 1.160000] MMC: Setting controller bus width to 1
[ 1.160000] mmc0: starting CMD0 arg 00000000 flags 000000c0
[ 1.160000] Sending command 0 as 00000800, arg = 00000000,
blocks = 0, length = 0 (MR = 00009B7C)
[ 1.160000] MCI irq: status = 0000C0E5, C07F0001, 00000001
[ 1.160000] Command ready
[ 1.160000] Completed command
[ 1.160000] Status = 00000001/0000c0e5 [00001008 00000000
00000000 00000000]
[ 1.160000] mmc0: req done (CMD0): 0: 00001008 00000000 00000000 00000000
[ 1.160000] mmc0: clock 400000Hz busmode 1 powermode 2 cs 0 Vdd
21 width 0 timing 0
[ 1.160000] clkdiv = 124. mcck = 397312
[ 1.160000] MMC: Setting controller bus width to 1
[ 1.160000] mmc0: starting CMD8 arg 000001aa flags 000002f5
[ 1.160000] Sending command 8 as 00001848, arg = 000001AA,
blocks = 0, length = 0 (MR = 00009B7C)
[ 1.160000] MCI irq: status = 0010C0E4, C07F0001, 00100000
[ 1.160000] MMC: Response timeout
[ 1.160000] Completed command
[ 1.160000] Status = 00100000/0010c0e5 [00001008 00000000
00000000 00000000]
[ 1.160000] Error detected and set to -110/0 (cmd = 8, retries = 0)
[ 1.160000] mmc0: req done (CMD8): -110: 00001008 00000000
00000000 00000000
[ 1.160000] mmc0: starting CMD5 arg 00000000 flags 000002e1
[ 1.160000] Sending command 5 as 00001845, arg = 00000000,
blocks = 0, length = 0 (MR = 00009B7C)
[ 1.160000] MCI irq: status = 0010C0E4, C07F0001, 00100000
[ 1.160000] MMC: Response timeout
[ 1.160000] Completed command
[ 1.160000] Status = 00100000/0010c0e5 [00001008 00000000
00000000 00000000]
[ 1.160000] Error detected and set to -110/0 (cmd = 5, retries = 3)
[ 1.160000] mmc0: req failed (CMD5): -110, retrying...
[ 1.160000] Sending command 5 as 00001845, arg = 00000000,
blocks = 0, length = 0 (MR = 00009B7C)
[ 1.170000] MCI irq: status = 0010C0E4, C07F0001, 00100000
[ 1.170000] MMC: Response timeout
[ 1.170000] Completed command
[ 1.170000] Status = 00100000/0010c0e5 [00001008 00000000
00000000 00000000]
[ 1.170000] Error detected and set to -110/0 (cmd = 5, retries = 2)
[ 1.170000] mmc0: req failed (CMD5): -110, retrying...
[ 1.170000] Sending command 5 as 00001845, arg = 00000000,
blocks = 0, length = 0 (MR = 00009B7C)
[ 1.170000] MCI irq: status = 0010C0E4, C07F0001, 00100000
[ 1.170000] MMC: Response timeout
[ 1.170000] Completed command
[ 1.170000] Status = 00100000/0010c0e5 [00001008 00000000
00000000 00000000]
[ 1.170000] Error detected and set to -110/0 (cmd = 5, retries = 1)
[ 1.170000] mmc0: req failed (CMD5): -110, retrying...
[ 1.170000] Sending command 5 as 00001845, arg = 00000000,
blocks = 0, length = 0 (MR = 00009B7C)
[ 1.170000] MCI irq: status = 0010C0E4, C07F0001, 00100000
[ 1.170000] MMC: Response timeout
[ 1.170000] Completed command
[ 1.170000] Status = 00100000/0010c0e5 [00001008 00000000
00000000 00000000]
[ 1.170000] Error detected and set to -110/0 (cmd = 5, retries = 0)
[ 1.170000] mmc0: req done (CMD5): -110: 00001008 00000000
00000000 00000000
[ 1.170000] mmc0: starting CMD55 arg 00000000 flags 000000f5
[ 1.170000] Sending command 55 as 00001877, arg = 00000000,
blocks = 0, length = 0 (MR = 00009B7C)
[ 1.180000] MCI irq: status = 0010C0E4, C07F0001, 00100000
[ 1.180000] MMC: Response timeout
[ 1.180000] Completed command
[ 1.180000] Status = 00100000/0010c0e5 [00001008 00000000
00000000 00000000]
[ 1.180000] Error detected and set to -110/0 (cmd = 55, retries = 0)
[ 1.180000] mmc0: req done (CMD55): -110: 00001008 00000000
00000000 00000000
[ 1.180000] mmc0: starting CMD55 arg 00000000 flags 000000f5
[ 1.180000] Sending command 55 as 00001877, arg = 00000000,
blocks = 0, length = 0 (MR = 00009B7C)
[ 1.180000] MCI irq: status = 0010C0E4, C07F0001, 00100000
[ 1.180000] MMC: Response timeout
[ 1.180000] Completed command
[ 1.180000] Status = 00100000/0010c0e5 [00001008 00000000
00000000 00000000]
[ 1.180000] Error detected and set to -110/0 (cmd = 55, retries = 0)
[ 1.180000] mmc0: req done (CMD55): -110: 00001008 00000000
00000000 00000000
[ 1.180000] mmc0: starting CMD55 arg 00000000 flags 000000f5
[ 1.180000] Sending command 55 as 00001877, arg = 00000000,
blocks = 0, length = 0 (MR = 00009B7C)
[ 1.180000] MCI irq: status = 0010C0E4, C07F0001, 00100000
[ 1.180000] MMC: Response timeout
[ 1.180000] Completed command
[ 1.180000] Status = 00100000/0010c0e5 [00001008 00000000
00000000 00000000]
[ 1.180000] Error detected and set to -110/0 (cmd = 55, retries = 0)
[ 1.180000] mmc0: req done (CMD55): -110: 00001008 00000000
00000000 00000000
[ 1.180000] mmc0: starting CMD55 arg 00000000 flags 000000f5
[ 1.180000] Sending command 55 as 00001877, arg = 00000000,
blocks = 0, length = 0 (MR = 00009B7C)
[ 1.180000] MCI irq: status = 0010C0E4, C07F0001, 00100000
[ 1.180000] MMC: Response timeout
[ 1.180000] Completed command
[ 1.180000] Status = 00100000/0010c0e5 [00001008 00000000
00000000 00000000]
[ 1.180000] Error detected and set to -110/0 (cmd = 55, retries = 0)
[ 1.180000] mmc0: req done (CMD55): -110: 00001008 00000000
00000000 00000000
[ 1.180000] mmc0: starting CMD1 arg 00000000 flags 000000e1
[ 1.180000] Clearing timeout
[ 1.180000] Clearing: SR = 0000C0E4
[ 1.180000] Clearing: SR = 0000C0E4
[ 1.180000] Clearing: SR = 0000C0E4
[ 1.180000] Clearing: SR = 0000C0E4
[ 1.180000] Sending command 1 as 00001841, arg = 00000000,
blocks = 0, length = 0 (MR = 00009B7C)
[ 1.180000] MCI irq: status = 0010C0E4, C07F0001, 00100000
[ 1.180000] MMC: Response timeout
[ 1.180000] Completed command
[ 1.180000] Status = 00100000/0010c0e5 [00001008 00000000
00000000 00000000]
[ 1.180000] Error detected and set to -110/0 (cmd = 1, retries = 0)
[ 1.180000] mmc0: req done (CMD1): -110: 00001008 00000000
00000000 00000000
[ 1.180000] mmc0: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0
width 0 timing 0
[ 1.180000] MMC: Setting controller bus width to 1
Thanks in advance for any suggestion,
Regards,
D.MOUSSAUD.
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2010-03-22 19:16 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2010-03-22 19:15 the at91 mci controller does not recognized my libertas 8686 sdio wifi chip after a reset David MOUSSAUD
-- strict thread matches above, loose matches on Subject: below --
2010-03-21 10:27 David MOUSSAUD
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).