From: Dinh Nguyen <dinguyen@kernel.org>
To: Tanmay Kathpalia <tanmay.kathpalia@altera.com>,
linux-mmc@vger.kernel.org
Cc: ulfh@kernel.org, adrian.hunter@intel.com, krzk+dt@kernel.org,
robh@kernel.org, conor+dt@kernel.org, p.zabel@pengutronix.de,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: Re: [PATCH v4 2/8] arm64: dts: agilex5: add SD/eMMC host controller
Date: Wed, 19 Aug 2026 08:04:45 -0500 [thread overview]
Message-ID: <fcc5c96a-5b68-4eb3-bee2-952aa9029631@kernel.org> (raw)
In-Reply-To: <20260810190025.25045-3-tanmay.kathpalia@altera.com>
On 8/10/26 14:00, Tanmay Kathpalia wrote:
> The Agilex5 HPS includes a Cadence SD6HC that drives either an SD card
> or eMMC, depending on the SOCDK daughter card. It uses separate SDMCLK
> (CIU) and L4_MP (BIU) clocks, and has three resets for the host
> controller, Combo PHY, and SDMMC OCP bridge. DMA for this controller
> requires the SMMU (stream ID 5), so the SOCDK board enables it.
>
> On the SOCDK OOBE card the slot is SD-only: fixed 3.3 V card supply and
> a GPIO-selected 3.3 V / 1.8 V I/O supply for UHS-I signalling up to
> SDR104.
>
> Signed-off-by: Tanmay Kathpalia <tanmay.kathpalia@altera.com>
> ---
> Depends on commit ab45ecfab540 ("dt-bindings: reset: altr: add
> COMBOPHY_RESET for Agilex5"), which is already in mainline via the
> reset tree. It is not yet in mmc/next; apply or merge that commit when
> building/testing this patch on top of mmc/next.
>
> .../arm64/boot/dts/intel/socfpga_agilex5.dtsi | 25 ++++++++++++
> .../boot/dts/intel/socfpga_agilex5_socdk.dts | 38 ++++++++++++++++++-
> 2 files changed, 62 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm64/boot/dts/intel/socfpga_agilex5.dtsi b/arch/arm64/boot/dts/intel/socfpga_agilex5.dtsi
> index b06c6d5d60ee..5ccbd7bf2034 100644
> --- a/arch/arm64/boot/dts/intel/socfpga_agilex5.dtsi
> +++ b/arch/arm64/boot/dts/intel/socfpga_agilex5.dtsi
> @@ -300,6 +300,31 @@ portb: gpio-controller@0 {
> };
> };
>
> + /*
> + * Shared SD/eMMC controller node. On the SOCDK OOBE daughter-card
> + * this is used for SD card operation; on the SOCDK eMMC daughter-card
> + * it is configured for eMMC.
> + */
> + emmc: mmc@10808000 {
> + compatible = "altr,agilex5-sd6hc", "cdns,sd6hc";
> + reg = <0x10808000 0x1000>;
> + /*
> + * "ciu" (SDMCLK) is listed first so it is selected as the
> + * primary clock by the SDHCI platform layer; the SD6HC PHY
> + * timing calculations are derived from this clock rate.
> + */
> + clocks = <&clkmgr AGILEX5_SDMCLK>, <&clkmgr AGILEX5_L4_MP_CLK>;
> + clock-names = "ciu", "biu";
> + dma-coherent;
> + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
> + iommus = <&smmu 5>;
> + resets = <&rst SDMMC_RESET>, <&rst COMBOPHY_RESET>,
> + <&rst SDMMC_OCP_RESET>;
> + reset-names = "sdhc-reset", "combophy", "sdmmc-ocp";
> +
> + status = "disabled";
> + };
> +
> nand: nand-controller@10b80000 {
> compatible = "cdns,hp-nfc";
> reg = <0x10b80000 0x10000>,
> diff --git a/arch/arm64/boot/dts/intel/socfpga_agilex5_socdk.dts b/arch/arm64/boot/dts/intel/socfpga_agilex5_socdk.dts
> index 57d3c5807c65..f37038066922 100644
> --- a/arch/arm64/boot/dts/intel/socfpga_agilex5_socdk.dts
> +++ b/arch/arm64/boot/dts/intel/socfpga_agilex5_socdk.dts
> @@ -36,9 +36,37 @@ memory@80000000 {
> /* We expect the bootloader to fill in the reg */
> reg = <0x0 0x80000000 0x0 0x0>;
> };
> +
> + vqmmc_io_reg: regulator-1p8v {
> + compatible = "regulator-gpio";
> + gpios = <&portb 3 GPIO_ACTIVE_HIGH>;
> + gpios-states = <0>;
> + regulator-max-microvolt = <3300000>;
> + regulator-min-microvolt = <1800000>;
> + regulator-name = "vqmmc-io";
> + states = <1800000 0x1>,
> + <3300000 0x0>;
> + };
> +
> + vmmc_reg: regulator-fixed-3p3v {
> + compatible = "regulator-fixed";
> + regulator-always-on;
> + regulator-max-microvolt = <3300000>;
> + regulator-min-microvolt = <3300000>;
> + regulator-name = "vcc-sd";
> + };
> };
>
> -&gpio0 {
> +&emmc {
> + bus-width = <4>;
> + cap-sd-highspeed;
> + disable-wp;
> + max-frequency = <200000000>;
> + no-mmc;
> + sd-uhs-sdr104;
> + vmmc-supply = <&vmmc_reg>;
> + vqmmc-supply = <&vqmmc_io_reg>;
> +
> status = "okay";
> };
>
> @@ -59,6 +87,10 @@ emac2_phy0: ethernet-phy@0 {
> };
> };
>
> +&gpio0 {
> + status = "okay";
> +};
> +
> &gpio1 {
> status = "okay";
> };
> @@ -100,6 +132,10 @@ root: partition@4200000 {
> };
> };
>
> +&smmu {
> + status = "okay";
> +};
> +
you should no longer need this because of
10cf797f3f8a ("arm64: dts: socfpga: agilex5: Enable the SMMU")
Thanks,
Dinh
next prev parent reply other threads:[~2026-08-19 13:04 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-08-10 19:00 [PATCH v4 0/8] mmc: sdhci-cadence: add SD6HC support and Agilex5 enablement Tanmay Kathpalia
2026-08-10 19:00 ` [PATCH v4 1/8] dt-bindings: mmc: add Cadence SD6HC binding Tanmay Kathpalia
2026-08-12 10:29 ` Krzysztof Kozlowski
2026-08-10 19:00 ` [PATCH v4 2/8] arm64: dts: agilex5: add SD/eMMC host controller Tanmay Kathpalia
2026-08-19 13:04 ` Dinh Nguyen [this message]
2026-08-10 19:00 ` [PATCH v4 3/8] dt-bindings: arm: altera: add Agilex5 SOCDK eMMC board variant Tanmay Kathpalia
2026-08-10 19:00 ` [PATCH v4 4/8] arm64: dts: agilex5: add SOCDK eMMC daughter board Tanmay Kathpalia
2026-08-10 19:00 ` [PATCH v4 5/8] mmc: sdhci-cadence: rename SD4HC symbols for SD6HC groundwork Tanmay Kathpalia
2026-08-10 19:00 ` [PATCH v4 6/8] mmc: sdhci-cadence: refactor driver structure for V6 controller support Tanmay Kathpalia
2026-08-10 19:00 ` [PATCH v4 7/8] mmc: sdhci-cadence: add Cadence SD6HC support Tanmay Kathpalia
2026-08-10 19:00 ` [PATCH v4 8/8] mmc: sdhci-cadence: add Altera Agilex5 " Tanmay Kathpalia
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=fcc5c96a-5b68-4eb3-bee2-952aa9029631@kernel.org \
--to=dinguyen@kernel.org \
--cc=adrian.hunter@intel.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
--cc=p.zabel@pengutronix.de \
--cc=robh@kernel.org \
--cc=tanmay.kathpalia@altera.com \
--cc=ulfh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox