* [PATCH V8 0/2] HS200 Mode support for device and host
@ 2011-12-23 7:12 Girish K S
2011-12-23 7:12 ` [PATCH V8 1/2] mmc: core: HS200 mode support for eMMC 4.5 Girish K S
` (2 more replies)
0 siblings, 3 replies; 7+ messages in thread
From: Girish K S @ 2011-12-23 7:12 UTC (permalink / raw)
To: linux-mmc; +Cc: patches, linux-samsung-soc, Girish K S
changes in v7:
Updated with review comments for minor changes in host conditional
handling. added the handling for 4 bit bus width.
Changes in v6:
split the patch into 2 and classified them as a patch for device
and host. Modified to include the review comments.
Changes in v5:
Reduced the case statements for better code readability. Removed
unused macro definitions. Modified the tuning function prototype
and definition to support tuning for both SD and eMMC cards.
Changes in v4:
Rebased onto chris-mmc/mmc-next branch. This patch is successfully
applied on commit with id de022ed3fdc14808299b2fa66dbb1ed5ab921912.
Changes in v3:
In the previous commits of chris-mmc/mmc-next branch, the patch with
commit id (c0f22a2c92e357e7cb3988b0b13034d70b7461f9) defines caps2 for
more capabilities. This patch version deletes the member ext_caps(created
in my earlier patch) from struct mmc_host and reuses already accepted
caps2 member.
Changes in v2:
Rebased to latest chris-mmc/mmc-next branch. Resolved indentation
problems identified in review. This patch has to be applied before
the patch released for modifying the printk messages.
Changes in v1:
Case statements in switch that produce same result have
been combined to reduce repeated assignments.
patch recreated after rebase to chris balls mmc-next branch.
Girish K S (2):
mmc: core: HS200 mode support for eMMC 4.5
mmc: host: Adds support for eMMC 4.5 HS200 mode
drivers/mmc/core/bus.c | 3 +-
drivers/mmc/core/debugfs.c | 3 +
drivers/mmc/core/mmc.c | 163 +++++++++++++++++++++++++++++++++++++++++---
drivers/mmc/core/sd.c | 3 +-
drivers/mmc/core/sdio.c | 4 +-
drivers/mmc/host/sdhci.c | 45 +++++++++---
drivers/mmc/host/sdhci.h | 1 +
include/linux/mmc/card.h | 3 +
include/linux/mmc/host.h | 11 +++-
include/linux/mmc/mmc.h | 66 +++++++++++++++++-
include/linux/mmc/sdhci.h | 1 +
11 files changed, 278 insertions(+), 25 deletions(-)
^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH V8 1/2] mmc: core: HS200 mode support for eMMC 4.5
2011-12-23 7:12 [PATCH V8 0/2] HS200 Mode support for device and host Girish K S
@ 2011-12-23 7:12 ` Girish K S
2011-12-23 9:06 ` Subhash Jadavani
2012-01-02 22:51 ` Chris Ball
2011-12-23 7:12 ` [PATCH V8 2/2] mmc: host: Adds support for eMMC 4.5 HS200 mode Girish K S
2011-12-29 11:49 ` [PATCH V8 0/2] HS200 Mode support for device and host Girish K S
2 siblings, 2 replies; 7+ messages in thread
From: Girish K S @ 2011-12-23 7:12 UTC (permalink / raw)
To: linux-mmc
Cc: patches, linux-samsung-soc, Girish K S, Chris Ball, Philip Rakity
This patch adds the support of the HS200 bus speed for eMMC 4.5 devices.
The eMMC 4.5 devices have support for 200MHz bus speed. The function
prototype of the tuning function is modified to handle the tuning command
number which is different in sd and mmc case.
cc: Chris Ball <cjb@laptop.org>
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Philip Rakity <prakity@marvell.com>
---
drivers/mmc/core/bus.c | 3 +-
drivers/mmc/core/debugfs.c | 3 +
drivers/mmc/core/mmc.c | 163 +++++++++++++++++++++++++++++++++++++++++---
drivers/mmc/core/sd.c | 3 +-
drivers/mmc/core/sdio.c | 4 +-
include/linux/mmc/card.h | 3 +
include/linux/mmc/host.h | 11 +++-
include/linux/mmc/mmc.h | 66 +++++++++++++++++-
8 files changed, 242 insertions(+), 14 deletions(-)
diff --git a/drivers/mmc/core/bus.c b/drivers/mmc/core/bus.c
index f8a228a..5d011a3 100644
--- a/drivers/mmc/core/bus.c
+++ b/drivers/mmc/core/bus.c
@@ -303,10 +303,11 @@ int mmc_add_card(struct mmc_card *card)
mmc_card_ddr_mode(card) ? "DDR " : "",
type);
} else {
- printk(KERN_INFO "%s: new %s%s%s card at address %04x\n",
+ pr_info("%s: new %s%s%s%s card at address %04x\n",
mmc_hostname(card->host),
mmc_card_uhs(card) ? "ultra high speed " :
(mmc_card_highspeed(card) ? "high speed " : ""),
+ (mmc_card_hs200(card) ? "HS200 " : ""),
mmc_card_ddr_mode(card) ? "DDR " : "",
type, card->rca);
}
diff --git a/drivers/mmc/core/debugfs.c b/drivers/mmc/core/debugfs.c
index 027615d..9ab5b17 100644
--- a/drivers/mmc/core/debugfs.c
+++ b/drivers/mmc/core/debugfs.c
@@ -135,6 +135,9 @@ static int mmc_ios_show(struct seq_file *s, void *data)
case MMC_TIMING_UHS_DDR50:
str = "sd uhs DDR50";
break;
+ case MMC_TIMING_MMC_HS200:
+ str = "mmc high-speed SDR200";
+ break;
default:
str = "invalid";
break;
diff --git a/drivers/mmc/core/mmc.c b/drivers/mmc/core/mmc.c
index f0a9f1f..583cb42 100644
--- a/drivers/mmc/core/mmc.c
+++ b/drivers/mmc/core/mmc.c
@@ -286,6 +286,27 @@ static int mmc_read_ext_csd(struct mmc_card *card, u8 *ext_csd)
}
card->ext_csd.raw_card_type = ext_csd[EXT_CSD_CARD_TYPE];
switch (ext_csd[EXT_CSD_CARD_TYPE] & EXT_CSD_CARD_TYPE_MASK) {
+ case EXT_CSD_CARD_TYPE_SDR_ALL:
+ case EXT_CSD_CARD_TYPE_SDR_ALL_DDR_1_8V:
+ case EXT_CSD_CARD_TYPE_SDR_ALL_DDR_1_2V:
+ case EXT_CSD_CARD_TYPE_SDR_ALL_DDR_52:
+ card->ext_csd.hs_max_dtr = 200000000;
+ card->ext_csd.card_type = EXT_CSD_CARD_TYPE_SDR_200;
+ break;
+ case EXT_CSD_CARD_TYPE_SDR_1_2V_ALL:
+ case EXT_CSD_CARD_TYPE_SDR_1_2V_DDR_1_8V:
+ case EXT_CSD_CARD_TYPE_SDR_1_2V_DDR_1_2V:
+ case EXT_CSD_CARD_TYPE_SDR_1_2V_DDR_52:
+ card->ext_csd.hs_max_dtr = 200000000;
+ card->ext_csd.card_type = EXT_CSD_CARD_TYPE_SDR_1_2V;
+ break;
+ case EXT_CSD_CARD_TYPE_SDR_1_8V_ALL:
+ case EXT_CSD_CARD_TYPE_SDR_1_8V_DDR_1_8V:
+ case EXT_CSD_CARD_TYPE_SDR_1_8V_DDR_1_2V:
+ case EXT_CSD_CARD_TYPE_SDR_1_8V_DDR_52:
+ card->ext_csd.hs_max_dtr = 200000000;
+ card->ext_csd.card_type = EXT_CSD_CARD_TYPE_SDR_1_8V;
+ break;
case EXT_CSD_CARD_TYPE_DDR_52 | EXT_CSD_CARD_TYPE_52 |
EXT_CSD_CARD_TYPE_26:
card->ext_csd.hs_max_dtr = 52000000;
@@ -700,6 +721,79 @@ static int mmc_select_powerclass(struct mmc_card *card,
}
/*
+ * Selects the desired buswidth and switch to the HS200 mode
+ * if bus width set without error
+ */
+static int mmc_select_hs200(struct mmc_card *card)
+{
+ int idx, err = 0;
+ struct mmc_host *host;
+ static unsigned ext_csd_bits[] = {
+ EXT_CSD_BUS_WIDTH_4,
+ EXT_CSD_BUS_WIDTH_8,
+ };
+ static unsigned bus_widths[] = {
+ MMC_BUS_WIDTH_4,
+ MMC_BUS_WIDTH_8,
+ };
+
+ BUG_ON(!card);
+
+ host = card->host;
+
+ if ((card->ext_csd.card_type & EXT_CSD_CARD_TYPE_SDR_1_2V)
+ && (host->caps2 & MMC_CAP2_HS200_1_2V_SDR))
+ if (mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_120, 0))
+ err = mmc_set_signal_voltage(host,
+ MMC_SIGNAL_VOLTAGE_180, 0);
+
+ /* If fails try again during next card power cycle */
+ if (err)
+ goto err;
+
+ idx = (host->caps & MMC_CAP_8_BIT_DATA) ? 1 : 0;
+
+ /*
+ * Unlike SD, MMC cards dont have a configuration register to notify
+ * supported bus width. So bus test command should be run to identify
+ * the supported bus width or compare the ext csd values of current
+ * bus width and ext csd values of 1 bit mode read earlier.
+ */
+ for (; idx >= 0; idx--) {
+
+ /*
+ * Host is capable of 8bit transfer, then switch
+ * the device to work in 8bit transfer mode. If the
+ * mmc switch command returns error then switch to
+ * 4bit transfer mode. On success set the corresponding
+ * bus width on the host.
+ */
+ err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
+ EXT_CSD_BUS_WIDTH,
+ ext_csd_bits[idx],
+ card->ext_csd.generic_cmd6_time);
+ if (err)
+ continue;
+
+ mmc_set_bus_width(card->host, bus_widths[idx]);
+
+ if (!(host->caps & MMC_CAP_BUS_WIDTH_TEST))
+ err = mmc_compare_ext_csds(card, bus_widths[idx]);
+ else
+ err = mmc_bus_test(card, bus_widths[idx]);
+ if (!err)
+ break;
+ }
+
+ /* switch to HS200 mode if bus width set successfully */
+ if (!err)
+ err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
+ EXT_CSD_HS_TIMING, 2, 0);
+err:
+ return err;
+}
+
+/*
* Handle the detection and initialisation of a card.
*
* In the case of a resume, "oldcard" will contain the card
@@ -905,11 +999,15 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
/*
* Activate high speed (if supported)
*/
- if ((card->ext_csd.hs_max_dtr != 0) &&
- (host->caps & MMC_CAP_MMC_HIGHSPEED)) {
- err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
- EXT_CSD_HS_TIMING, 1,
- card->ext_csd.generic_cmd6_time);
+ if (card->ext_csd.hs_max_dtr != 0) {
+ err = 0;
+ if ((card->ext_csd.hs_max_dtr > 52000000) &&
+ (host->caps2 & MMC_CAP2_HS200))
+ err = mmc_select_hs200(card);
+ else if (host->caps & MMC_CAP_MMC_HIGHSPEED)
+ err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
+ EXT_CSD_HS_TIMING, 1, 0);
+
if (err && err != -EBADMSG)
goto free_card;
@@ -918,8 +1016,15 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
mmc_hostname(card->host));
err = 0;
} else {
- mmc_card_set_highspeed(card);
- mmc_set_timing(card->host, MMC_TIMING_MMC_HS);
+ if ((card->ext_csd.hs_max_dtr > 52000000) &&
+ (host->caps2 & MMC_CAP2_HS200)) {
+ mmc_card_set_hs200(card);
+ mmc_set_timing(card->host,
+ MMC_TIMING_MMC_HS200);
+ } else {
+ mmc_card_set_highspeed(card);
+ mmc_set_timing(card->host, MMC_TIMING_MMC_HS);
+ }
}
}
@@ -944,7 +1049,7 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
*/
max_dtr = (unsigned int)-1;
- if (mmc_card_highspeed(card)) {
+ if (mmc_card_highspeed(card) || mmc_card_hs200(card)) {
if (max_dtr > card->ext_csd.hs_max_dtr)
max_dtr = card->ext_csd.hs_max_dtr;
} else if (max_dtr > card->csd.max_dtr) {
@@ -970,9 +1075,49 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
}
/*
+ * Indicate HS200 SDR mode (if supported).
+ */
+ if (mmc_card_hs200(card)) {
+ u32 ext_csd_bits;
+ u32 bus_width = card->host->ios.bus_width;
+
+ /*
+ * For devices supporting HS200 mode, the bus width has
+ * to be set before executing the tuning function. If
+ * set before tuning, then device will respond with CRC
+ * errors for responses on CMD line. So for HS200 the
+ * sequence will be
+ * 1. set bus width 4bit / 8 bit (1 bit not supported)
+ * 2. switch to HS200 mode
+ * 3. set the clock to > 52Mhz <=200MHz and
+ * 4. execute tuning for HS200
+ */
+ if ((host->caps2 & MMC_CAP2_HS200) &&
+ card->host->ops->execute_tuning)
+ err = card->host->ops->execute_tuning(card->host,
+ MMC_SEND_TUNING_BLOCK_HS200);
+ if (err) {
+ pr_warning("tuning execution failed\n");
+ goto err;
+ }
+
+ ext_csd_bits = (bus_width == MMC_BUS_WIDTH_8) ?
+ EXT_CSD_BUS_WIDTH_8 :
+ EXT_CSD_BUS_WIDTH_4;
+ err = mmc_select_powerclass(card, ext_csd_bits, ext_csd);
+ if (err) {
+ pr_err("%s: power class selection to bus width"
+ "%d failed\n", mmc_hostname(card->host),
+ 1 << bus_width);
+ goto err;
+ }
+ }
+
+ /*
* Activate wide bus and DDR (if supported).
*/
- if ((card->csd.mmca_vsn >= CSD_SPEC_VER_4) &&
+ if (!mmc_card_hs200(card) &&
+ (card->csd.mmca_vsn >= CSD_SPEC_VER_3) &&
(host->caps & (MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA))) {
static unsigned ext_csd_bits[][2] = {
{ EXT_CSD_BUS_WIDTH_8, EXT_CSD_DDR_BUS_WIDTH_8 },
diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c
index 6f27d35..a775131 100644
--- a/drivers/mmc/core/sd.c
+++ b/drivers/mmc/core/sd.c
@@ -661,7 +661,8 @@ static int mmc_sd_init_uhs_card(struct mmc_card *card)
/* SPI mode doesn't define CMD19 */
if (!mmc_host_is_spi(card->host) && card->host->ops->execute_tuning)
- err = card->host->ops->execute_tuning(card->host);
+ err = card->host->ops->execute_tuning(card->host, \
+ MMC_SEND_TUNING_BLOCK);
out:
kfree(status);
diff --git a/drivers/mmc/core/sdio.c b/drivers/mmc/core/sdio.c
index b77f770..bd7bacc 100644
--- a/drivers/mmc/core/sdio.c
+++ b/drivers/mmc/core/sdio.c
@@ -14,6 +14,7 @@
#include <linux/mmc/host.h>
#include <linux/mmc/card.h>
+#include <linux/mmc/mmc.h>
#include <linux/mmc/sdio.h>
#include <linux/mmc/sdio_func.h>
#include <linux/mmc/sdio_ids.h>
@@ -556,7 +557,8 @@ static int mmc_sdio_init_uhs_card(struct mmc_card *card)
/* Initialize and start re-tuning timer */
if (!mmc_host_is_spi(card->host) && card->host->ops->execute_tuning)
- err = card->host->ops->execute_tuning(card->host);
+ err = card->host->ops->execute_tuning(card->host,
+ MMC_SEND_TUNING_BLOCK);
out:
diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h
index 9478a6b..9f22ba5 100644
--- a/include/linux/mmc/card.h
+++ b/include/linux/mmc/card.h
@@ -216,6 +216,7 @@ struct mmc_card {
#define MMC_STATE_ULTRAHIGHSPEED (1<<5) /* card is in ultra high speed mode */
#define MMC_CARD_SDXC (1<<6) /* card is SDXC */
#define MMC_CARD_REMOVED (1<<7) /* card has been removed */
+#define MMC_STATE_HIGHSPEED_200 (1<<8) /* card is in HS200 mode */
unsigned int quirks; /* card quirks */
#define MMC_QUIRK_LENIENT_FN0 (1<<0) /* allow SDIO FN0 writes outside of the VS CCCR range */
#define MMC_QUIRK_BLKSZ_FOR_BYTE_MODE (1<<1) /* use func->cur_blksize */
@@ -374,6 +375,7 @@ static inline void __maybe_unused remove_quirk(struct mmc_card *card, int data)
#define mmc_card_present(c) ((c)->state & MMC_STATE_PRESENT)
#define mmc_card_readonly(c) ((c)->state & MMC_STATE_READONLY)
#define mmc_card_highspeed(c) ((c)->state & MMC_STATE_HIGHSPEED)
+#define mmc_card_hs200(c) ((c)->state & MMC_STATE_HIGHSPEED_200)
#define mmc_card_blockaddr(c) ((c)->state & MMC_STATE_BLOCKADDR)
#define mmc_card_ddr_mode(c) ((c)->state & MMC_STATE_HIGHSPEED_DDR)
#define mmc_card_uhs(c) ((c)->state & MMC_STATE_ULTRAHIGHSPEED)
@@ -384,6 +386,7 @@ static inline void __maybe_unused remove_quirk(struct mmc_card *card, int data)
#define mmc_card_set_present(c) ((c)->state |= MMC_STATE_PRESENT)
#define mmc_card_set_readonly(c) ((c)->state |= MMC_STATE_READONLY)
#define mmc_card_set_highspeed(c) ((c)->state |= MMC_STATE_HIGHSPEED)
+#define mmc_card_set_hs200(c) ((c)->state |= MMC_STATE_HIGHSPEED_200)
#define mmc_card_set_blockaddr(c) ((c)->state |= MMC_STATE_BLOCKADDR)
#define mmc_card_set_ddr_mode(c) ((c)->state |= MMC_STATE_HIGHSPEED_DDR)
#define mmc_card_set_uhs(c) ((c)->state |= MMC_STATE_ULTRAHIGHSPEED)
diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h
index 9a03d03..606c8c3 100644
--- a/include/linux/mmc/host.h
+++ b/include/linux/mmc/host.h
@@ -56,10 +56,13 @@ struct mmc_ios {
#define MMC_TIMING_UHS_SDR50 3
#define MMC_TIMING_UHS_SDR104 4
#define MMC_TIMING_UHS_DDR50 5
+#define MMC_TIMING_MMC_HS200 6
#define MMC_SDR_MODE 0
#define MMC_1_2V_DDR_MODE 1
#define MMC_1_8V_DDR_MODE 2
+#define MMC_1_2V_SDR_MODE 3
+#define MMC_1_8V_SDR_MODE 4
unsigned char signal_voltage; /* signalling voltage (1.8V or 3.3V) */
@@ -148,7 +151,9 @@ struct mmc_host_ops {
void (*init_card)(struct mmc_host *host, struct mmc_card *card);
int (*start_signal_voltage_switch)(struct mmc_host *host, struct mmc_ios *ios);
- int (*execute_tuning)(struct mmc_host *host);
+
+ /* The tuning command opcode value is different for SD and eMMC cards */
+ int (*execute_tuning)(struct mmc_host *host, u32 opcode);
void (*enable_preset_value)(struct mmc_host *host, bool enable);
int (*select_drive_strength)(unsigned int max_dtr, int host_drv, int card_drv);
void (*hw_reset)(struct mmc_host *host);
@@ -242,6 +247,10 @@ struct mmc_host {
#define MMC_CAP2_CACHE_CTRL (1 << 1) /* Allow cache control */
#define MMC_CAP2_POWEROFF_NOTIFY (1 << 2) /* Notify poweroff supported */
#define MMC_CAP2_NO_MULTI_READ (1 << 3) /* Multiblock reads don't work */
+#define MMC_CAP2_HS200_1_8V_SDR (1 << 4) /* can support */
+#define MMC_CAP2_HS200_1_2V_SDR (1 << 5) /* can support */
+#define MMC_CAP2_HS200 (MMC_CAP2_HS200_1_8V_SDR | \
+ MMC_CAP2_HS200_1_2V_SDR)
mmc_pm_flag_t pm_caps; /* supported pm features */
unsigned int power_notify_type;
diff --git a/include/linux/mmc/mmc.h b/include/linux/mmc/mmc.h
index 665548e..2c8cc69 100644
--- a/include/linux/mmc/mmc.h
+++ b/include/linux/mmc/mmc.h
@@ -51,6 +51,7 @@
#define MMC_READ_SINGLE_BLOCK 17 /* adtc [31:0] data addr R1 */
#define MMC_READ_MULTIPLE_BLOCK 18 /* adtc [31:0] data addr R1 */
#define MMC_SEND_TUNING_BLOCK 19 /* adtc R1 */
+#define MMC_SEND_TUNING_BLOCK_HS200 21 /* adtc R1 */
/* class 3 */
#define MMC_WRITE_DAT_UNTIL_STOP 20 /* adtc [31:0] data addr R1 */
@@ -339,13 +340,76 @@ struct _mmc_csd {
#define EXT_CSD_CARD_TYPE_26 (1<<0) /* Card can run at 26MHz */
#define EXT_CSD_CARD_TYPE_52 (1<<1) /* Card can run at 52MHz */
-#define EXT_CSD_CARD_TYPE_MASK 0xF /* Mask out reserved bits */
+#define EXT_CSD_CARD_TYPE_MASK 0x3F /* Mask out reserved bits */
#define EXT_CSD_CARD_TYPE_DDR_1_8V (1<<2) /* Card can run at 52MHz */
/* DDR mode @1.8V or 3V I/O */
#define EXT_CSD_CARD_TYPE_DDR_1_2V (1<<3) /* Card can run at 52MHz */
/* DDR mode @1.2V I/O */
#define EXT_CSD_CARD_TYPE_DDR_52 (EXT_CSD_CARD_TYPE_DDR_1_8V \
| EXT_CSD_CARD_TYPE_DDR_1_2V)
+#define EXT_CSD_CARD_TYPE_SDR_1_8V (1<<4) /* Card can run at 200MHz */
+#define EXT_CSD_CARD_TYPE_SDR_1_2V (1<<5) /* Card can run at 200MHz */
+ /* SDR mode @1.2V I/O */
+
+#define EXT_CSD_CARD_TYPE_SDR_200 (EXT_CSD_CARD_TYPE_SDR_1_8V \
+ | EXT_CSD_CARD_TYPE_SDR_1_2V)
+
+#define EXT_CSD_CARD_TYPE_SDR_ALL (EXT_CSD_CARD_TYPE_SDR_200 \
+ | EXT_CSD_CARD_TYPE_52 \
+ | EXT_CSD_CARD_TYPE_26)
+
+#define EXT_CSD_CARD_TYPE_SDR_1_2V_ALL (EXT_CSD_CARD_TYPE_SDR_1_2V \
+ | EXT_CSD_CARD_TYPE_52 \
+ | EXT_CSD_CARD_TYPE_26)
+
+#define EXT_CSD_CARD_TYPE_SDR_1_8V_ALL (EXT_CSD_CARD_TYPE_SDR_1_8V \
+ | EXT_CSD_CARD_TYPE_52 \
+ | EXT_CSD_CARD_TYPE_26)
+
+#define EXT_CSD_CARD_TYPE_SDR_1_2V_DDR_1_8V (EXT_CSD_CARD_TYPE_SDR_1_2V \
+ | EXT_CSD_CARD_TYPE_DDR_1_8V \
+ | EXT_CSD_CARD_TYPE_52 \
+ | EXT_CSD_CARD_TYPE_26)
+
+#define EXT_CSD_CARD_TYPE_SDR_1_8V_DDR_1_8V (EXT_CSD_CARD_TYPE_SDR_1_8V \
+ | EXT_CSD_CARD_TYPE_DDR_1_8V \
+ | EXT_CSD_CARD_TYPE_52 \
+ | EXT_CSD_CARD_TYPE_26)
+
+#define EXT_CSD_CARD_TYPE_SDR_1_2V_DDR_1_2V (EXT_CSD_CARD_TYPE_SDR_1_2V \
+ | EXT_CSD_CARD_TYPE_DDR_1_2V \
+ | EXT_CSD_CARD_TYPE_52 \
+ | EXT_CSD_CARD_TYPE_26)
+
+#define EXT_CSD_CARD_TYPE_SDR_1_8V_DDR_1_2V (EXT_CSD_CARD_TYPE_SDR_1_8V \
+ | EXT_CSD_CARD_TYPE_DDR_1_2V \
+ | EXT_CSD_CARD_TYPE_52 \
+ | EXT_CSD_CARD_TYPE_26)
+
+#define EXT_CSD_CARD_TYPE_SDR_1_2V_DDR_52 (EXT_CSD_CARD_TYPE_SDR_1_2V \
+ | EXT_CSD_CARD_TYPE_DDR_52 \
+ | EXT_CSD_CARD_TYPE_52 \
+ | EXT_CSD_CARD_TYPE_26)
+
+#define EXT_CSD_CARD_TYPE_SDR_1_8V_DDR_52 (EXT_CSD_CARD_TYPE_SDR_1_8V \
+ | EXT_CSD_CARD_TYPE_DDR_52 \
+ | EXT_CSD_CARD_TYPE_52 \
+ | EXT_CSD_CARD_TYPE_26)
+
+#define EXT_CSD_CARD_TYPE_SDR_ALL_DDR_1_8V (EXT_CSD_CARD_TYPE_SDR_200 \
+ | EXT_CSD_CARD_TYPE_DDR_1_8V \
+ | EXT_CSD_CARD_TYPE_52 \
+ | EXT_CSD_CARD_TYPE_26)
+
+#define EXT_CSD_CARD_TYPE_SDR_ALL_DDR_1_2V (EXT_CSD_CARD_TYPE_SDR_200 \
+ | EXT_CSD_CARD_TYPE_DDR_1_2V \
+ | EXT_CSD_CARD_TYPE_52 \
+ | EXT_CSD_CARD_TYPE_26)
+
+#define EXT_CSD_CARD_TYPE_SDR_ALL_DDR_52 (EXT_CSD_CARD_TYPE_SDR_200 \
+ | EXT_CSD_CARD_TYPE_DDR_52 \
+ | EXT_CSD_CARD_TYPE_52 \
+ | EXT_CSD_CARD_TYPE_26)
#define EXT_CSD_BUS_WIDTH_1 0 /* Card is in 1 bit mode */
#define EXT_CSD_BUS_WIDTH_4 1 /* Card is in 4 bit mode */
--
1.7.1
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH V8 2/2] mmc: host: Adds support for eMMC 4.5 HS200 mode
2011-12-23 7:12 [PATCH V8 0/2] HS200 Mode support for device and host Girish K S
2011-12-23 7:12 ` [PATCH V8 1/2] mmc: core: HS200 mode support for eMMC 4.5 Girish K S
@ 2011-12-23 7:12 ` Girish K S
2011-12-29 11:49 ` [PATCH V8 0/2] HS200 Mode support for device and host Girish K S
2 siblings, 0 replies; 7+ messages in thread
From: Girish K S @ 2011-12-23 7:12 UTC (permalink / raw)
To: linux-mmc; +Cc: patches, linux-samsung-soc, Girish K S, Chris Ball
This patch adds support for the HS200 mode on the host side.
Also enables the tuning feature required when the HS200 mode
is selected.
cc: Chris Ball <cjb@laptop.org>
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
---
drivers/mmc/host/sdhci.c | 45 ++++++++++++++++++++++++++++++++++-----------
drivers/mmc/host/sdhci.h | 1 +
include/linux/mmc/sdhci.h | 1 +
3 files changed, 36 insertions(+), 11 deletions(-)
diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
index ab6018f..fb17e95 100644
--- a/drivers/mmc/host/sdhci.c
+++ b/drivers/mmc/host/sdhci.c
@@ -49,7 +49,7 @@ static void sdhci_finish_data(struct sdhci_host *);
static void sdhci_send_command(struct sdhci_host *, struct mmc_command *);
static void sdhci_finish_command(struct sdhci_host *);
-static int sdhci_execute_tuning(struct mmc_host *mmc);
+static int sdhci_execute_tuning(struct mmc_host *mmc, u32 opcode);
static void sdhci_tuning_timer(unsigned long data);
#ifdef CONFIG_PM_RUNTIME
@@ -1016,7 +1016,8 @@ static void sdhci_send_command(struct sdhci_host *host, struct mmc_command *cmd)
flags |= SDHCI_CMD_INDEX;
/* CMD19 is special in that the Data Present Select should be set */
- if (cmd->data || (cmd->opcode == MMC_SEND_TUNING_BLOCK))
+ if (cmd->data || (cmd->opcode == MMC_SEND_TUNING_BLOCK) ||
+ (cmd->opcode == MMC_SEND_TUNING_BLOCK_HS200))
flags |= SDHCI_CMD_DATA;
sdhci_writew(host, SDHCI_MAKE_CMD(cmd->opcode, flags), SDHCI_COMMAND);
@@ -1287,7 +1288,7 @@ static void sdhci_request(struct mmc_host *mmc, struct mmc_request *mrq)
if ((host->flags & SDHCI_NEEDS_RETUNING) &&
!(present_state & (SDHCI_DOING_WRITE | SDHCI_DOING_READ))) {
spin_unlock_irqrestore(&host->lock, flags);
- sdhci_execute_tuning(mmc);
+ sdhci_execute_tuning(mmc, mrq->cmd->opcode);
spin_lock_irqsave(&host->lock, flags);
/* Restore original mmc_request structure */
@@ -1371,7 +1372,8 @@ static void sdhci_do_set_ios(struct sdhci_host *host, struct mmc_ios *ios)
unsigned int clock;
/* In case of UHS-I modes, set High Speed Enable */
- if ((ios->timing == MMC_TIMING_UHS_SDR50) ||
+ if ((ios->timing == MMC_TIMING_MMC_HS200) ||
+ (ios->timing == MMC_TIMING_UHS_SDR50) ||
(ios->timing == MMC_TIMING_UHS_SDR104) ||
(ios->timing == MMC_TIMING_UHS_DDR50) ||
(ios->timing == MMC_TIMING_UHS_SDR25) ||
@@ -1425,7 +1427,9 @@ static void sdhci_do_set_ios(struct sdhci_host *host, struct mmc_ios *ios)
ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
/* Select Bus Speed Mode for host */
ctrl_2 &= ~SDHCI_CTRL_UHS_MASK;
- if (ios->timing == MMC_TIMING_UHS_SDR12)
+ if (ios->timing == MMC_TIMING_MMC_HS200)
+ ctrl_2 |= SDHCI_CTRL_HS_SDR200;
+ else if (ios->timing == MMC_TIMING_UHS_SDR12)
ctrl_2 |= SDHCI_CTRL_UHS_SDR12;
else if (ios->timing == MMC_TIMING_UHS_SDR25)
ctrl_2 |= SDHCI_CTRL_UHS_SDR25;
@@ -1673,7 +1677,7 @@ static int sdhci_start_signal_voltage_switch(struct mmc_host *mmc,
return err;
}
-static int sdhci_execute_tuning(struct mmc_host *mmc)
+static int sdhci_execute_tuning(struct mmc_host *mmc, u32 opcode)
{
struct sdhci_host *host;
u16 ctrl;
@@ -1694,10 +1698,13 @@ static int sdhci_execute_tuning(struct mmc_host *mmc)
* Host Controller needs tuning only in case of SDR104 mode
* and for SDR50 mode when Use Tuning for SDR50 is set in
* Capabilities register.
+ * If the Host Controller supports the HS200 mode then tuning
+ * function has to be executed.
*/
if (((ctrl & SDHCI_CTRL_UHS_MASK) == SDHCI_CTRL_UHS_SDR104) ||
(((ctrl & SDHCI_CTRL_UHS_MASK) == SDHCI_CTRL_UHS_SDR50) &&
- (host->flags & SDHCI_SDR50_NEEDS_TUNING)))
+ (host->flags & SDHCI_SDR50_NEEDS_TUNING)) ||
+ (host->flags & SDHCI_HS200_NEEDS_TUNING))
ctrl |= SDHCI_CTRL_EXEC_TUNING;
else {
spin_unlock(&host->lock);
@@ -1733,7 +1740,7 @@ static int sdhci_execute_tuning(struct mmc_host *mmc)
if (!tuning_loop_counter && !timeout)
break;
- cmd.opcode = MMC_SEND_TUNING_BLOCK;
+ cmd.opcode = opcode;
cmd.arg = 0;
cmd.flags = MMC_RSP_R1 | MMC_CMD_ADTC;
cmd.retries = 0;
@@ -1748,7 +1755,17 @@ static int sdhci_execute_tuning(struct mmc_host *mmc)
* block to the Host Controller. So we set the block size
* to 64 here.
*/
- sdhci_writew(host, SDHCI_MAKE_BLKSZ(7, 64), SDHCI_BLOCK_SIZE);
+ if (cmd.opcode == MMC_SEND_TUNING_BLOCK_HS200) {
+ if (mmc->ios.bus_width == MMC_BUS_WIDTH_8)
+ sdhci_writew(host, SDHCI_MAKE_BLKSZ(7, 128),
+ SDHCI_BLOCK_SIZE);
+ else if (mmc->ios.bus_width == MMC_BUS_WIDTH_4)
+ sdhci_writew(host, SDHCI_MAKE_BLKSZ(7, 64),
+ SDHCI_BLOCK_SIZE);
+ } else {
+ sdhci_writew(host, SDHCI_MAKE_BLKSZ(7, 64),
+ SDHCI_BLOCK_SIZE);
+ }
/*
* The tuning block is sent by the card to the host controller.
@@ -2131,12 +2148,14 @@ static void sdhci_show_adma_error(struct sdhci_host *host) { }
static void sdhci_data_irq(struct sdhci_host *host, u32 intmask)
{
+ u32 command;
BUG_ON(intmask == 0);
/* CMD19 generates _only_ Buffer Read Ready interrupt */
if (intmask & SDHCI_INT_DATA_AVAIL) {
- if (SDHCI_GET_CMD(sdhci_readw(host, SDHCI_COMMAND)) ==
- MMC_SEND_TUNING_BLOCK) {
+ command = SDHCI_GET_CMD(sdhci_readw(host, SDHCI_COMMAND));
+ if ((command == MMC_SEND_TUNING_BLOCK) ||
+ (command == MMC_SEND_TUNING_BLOCK_HS200)) {
host->tuning_done = 1;
wake_up(&host->buf_ready_int);
return;
@@ -2741,6 +2760,10 @@ int sdhci_add_host(struct sdhci_host *host)
if (caps[1] & SDHCI_USE_SDR50_TUNING)
host->flags |= SDHCI_SDR50_NEEDS_TUNING;
+ /* Does the host needs tuning for HS200? */
+ if (mmc->caps2 & MMC_CAP2_HS200)
+ host->flags |= SDHCI_HS200_NEEDS_TUNING;
+
/* Driver Type(s) (A, C, D) supported by the host */
if (caps[1] & SDHCI_DRIVER_TYPE_A)
mmc->caps |= MMC_CAP_DRIVER_TYPE_A;
diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h
index a04d4d0..46fd2ac 100644
--- a/drivers/mmc/host/sdhci.h
+++ b/drivers/mmc/host/sdhci.h
@@ -158,6 +158,7 @@
#define SDHCI_CTRL_UHS_SDR50 0x0002
#define SDHCI_CTRL_UHS_SDR104 0x0003
#define SDHCI_CTRL_UHS_DDR50 0x0004
+#define SDHCI_CTRL_HS_SDR200 0x0005 /*reserved value in SDIO spec */
#define SDHCI_CTRL_VDD_180 0x0008
#define SDHCI_CTRL_DRV_TYPE_MASK 0x0030
#define SDHCI_CTRL_DRV_TYPE_B 0x0000
diff --git a/include/linux/mmc/sdhci.h b/include/linux/mmc/sdhci.h
index e4b6935..d9a2222 100644
--- a/include/linux/mmc/sdhci.h
+++ b/include/linux/mmc/sdhci.h
@@ -121,6 +121,7 @@ struct sdhci_host {
#define SDHCI_AUTO_CMD23 (1<<7) /* Auto CMD23 support */
#define SDHCI_PV_ENABLED (1<<8) /* Preset value enabled */
#define SDHCI_SDIO_IRQ_ENABLED (1<<9) /* SDIO irq enabled */
+#define SDHCI_HS200_NEEDS_TUNING (1<<10) /* HS200 needs tuning */
unsigned int version; /* SDHCI spec. version */
--
1.7.1
^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: [PATCH V8 1/2] mmc: core: HS200 mode support for eMMC 4.5
2011-12-23 7:12 ` [PATCH V8 1/2] mmc: core: HS200 mode support for eMMC 4.5 Girish K S
@ 2011-12-23 9:06 ` Subhash Jadavani
2012-01-02 22:51 ` Chris Ball
1 sibling, 0 replies; 7+ messages in thread
From: Subhash Jadavani @ 2011-12-23 9:06 UTC (permalink / raw)
To: Girish K S
Cc: linux-mmc, patches, linux-samsung-soc, Chris Ball, Philip Rakity
Looks good to me.
Acked-by: Subhash Jadavani <subhashj@codeaurora.org>
Regards,
Subhash
On 12/23/2011 12:42 PM, Girish K S wrote:
> This patch adds the support of the HS200 bus speed for eMMC 4.5 devices.
> The eMMC 4.5 devices have support for 200MHz bus speed. The function
> prototype of the tuning function is modified to handle the tuning command
> number which is different in sd and mmc case.
>
> cc: Chris Ball<cjb@laptop.org>
> Signed-off-by: Girish K S<girish.shivananjappa@linaro.org>
> Signed-off-by: Philip Rakity<prakity@marvell.com>
> ---
> drivers/mmc/core/bus.c | 3 +-
> drivers/mmc/core/debugfs.c | 3 +
> drivers/mmc/core/mmc.c | 163 +++++++++++++++++++++++++++++++++++++++++---
> drivers/mmc/core/sd.c | 3 +-
> drivers/mmc/core/sdio.c | 4 +-
> include/linux/mmc/card.h | 3 +
> include/linux/mmc/host.h | 11 +++-
> include/linux/mmc/mmc.h | 66 +++++++++++++++++-
> 8 files changed, 242 insertions(+), 14 deletions(-)
>
> diff --git a/drivers/mmc/core/bus.c b/drivers/mmc/core/bus.c
> index f8a228a..5d011a3 100644
> --- a/drivers/mmc/core/bus.c
> +++ b/drivers/mmc/core/bus.c
> @@ -303,10 +303,11 @@ int mmc_add_card(struct mmc_card *card)
> mmc_card_ddr_mode(card) ? "DDR " : "",
> type);
> } else {
> - printk(KERN_INFO "%s: new %s%s%s card at address %04x\n",
> + pr_info("%s: new %s%s%s%s card at address %04x\n",
> mmc_hostname(card->host),
> mmc_card_uhs(card) ? "ultra high speed " :
> (mmc_card_highspeed(card) ? "high speed " : ""),
> + (mmc_card_hs200(card) ? "HS200 " : ""),
> mmc_card_ddr_mode(card) ? "DDR " : "",
> type, card->rca);
> }
> diff --git a/drivers/mmc/core/debugfs.c b/drivers/mmc/core/debugfs.c
> index 027615d..9ab5b17 100644
> --- a/drivers/mmc/core/debugfs.c
> +++ b/drivers/mmc/core/debugfs.c
> @@ -135,6 +135,9 @@ static int mmc_ios_show(struct seq_file *s, void *data)
> case MMC_TIMING_UHS_DDR50:
> str = "sd uhs DDR50";
> break;
> + case MMC_TIMING_MMC_HS200:
> + str = "mmc high-speed SDR200";
> + break;
> default:
> str = "invalid";
> break;
> diff --git a/drivers/mmc/core/mmc.c b/drivers/mmc/core/mmc.c
> index f0a9f1f..583cb42 100644
> --- a/drivers/mmc/core/mmc.c
> +++ b/drivers/mmc/core/mmc.c
> @@ -286,6 +286,27 @@ static int mmc_read_ext_csd(struct mmc_card *card, u8 *ext_csd)
> }
> card->ext_csd.raw_card_type = ext_csd[EXT_CSD_CARD_TYPE];
> switch (ext_csd[EXT_CSD_CARD_TYPE]& EXT_CSD_CARD_TYPE_MASK) {
> + case EXT_CSD_CARD_TYPE_SDR_ALL:
> + case EXT_CSD_CARD_TYPE_SDR_ALL_DDR_1_8V:
> + case EXT_CSD_CARD_TYPE_SDR_ALL_DDR_1_2V:
> + case EXT_CSD_CARD_TYPE_SDR_ALL_DDR_52:
> + card->ext_csd.hs_max_dtr = 200000000;
> + card->ext_csd.card_type = EXT_CSD_CARD_TYPE_SDR_200;
> + break;
> + case EXT_CSD_CARD_TYPE_SDR_1_2V_ALL:
> + case EXT_CSD_CARD_TYPE_SDR_1_2V_DDR_1_8V:
> + case EXT_CSD_CARD_TYPE_SDR_1_2V_DDR_1_2V:
> + case EXT_CSD_CARD_TYPE_SDR_1_2V_DDR_52:
> + card->ext_csd.hs_max_dtr = 200000000;
> + card->ext_csd.card_type = EXT_CSD_CARD_TYPE_SDR_1_2V;
> + break;
> + case EXT_CSD_CARD_TYPE_SDR_1_8V_ALL:
> + case EXT_CSD_CARD_TYPE_SDR_1_8V_DDR_1_8V:
> + case EXT_CSD_CARD_TYPE_SDR_1_8V_DDR_1_2V:
> + case EXT_CSD_CARD_TYPE_SDR_1_8V_DDR_52:
> + card->ext_csd.hs_max_dtr = 200000000;
> + card->ext_csd.card_type = EXT_CSD_CARD_TYPE_SDR_1_8V;
> + break;
> case EXT_CSD_CARD_TYPE_DDR_52 | EXT_CSD_CARD_TYPE_52 |
> EXT_CSD_CARD_TYPE_26:
> card->ext_csd.hs_max_dtr = 52000000;
> @@ -700,6 +721,79 @@ static int mmc_select_powerclass(struct mmc_card *card,
> }
>
> /*
> + * Selects the desired buswidth and switch to the HS200 mode
> + * if bus width set without error
> + */
> +static int mmc_select_hs200(struct mmc_card *card)
> +{
> + int idx, err = 0;
> + struct mmc_host *host;
> + static unsigned ext_csd_bits[] = {
> + EXT_CSD_BUS_WIDTH_4,
> + EXT_CSD_BUS_WIDTH_8,
> + };
> + static unsigned bus_widths[] = {
> + MMC_BUS_WIDTH_4,
> + MMC_BUS_WIDTH_8,
> + };
> +
> + BUG_ON(!card);
> +
> + host = card->host;
> +
> + if ((card->ext_csd.card_type& EXT_CSD_CARD_TYPE_SDR_1_2V)
> + && (host->caps2& MMC_CAP2_HS200_1_2V_SDR))
> + if (mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_120, 0))
> + err = mmc_set_signal_voltage(host,
> + MMC_SIGNAL_VOLTAGE_180, 0);
> +
> + /* If fails try again during next card power cycle */
> + if (err)
> + goto err;
> +
> + idx = (host->caps& MMC_CAP_8_BIT_DATA) ? 1 : 0;
> +
> + /*
> + * Unlike SD, MMC cards dont have a configuration register to notify
> + * supported bus width. So bus test command should be run to identify
> + * the supported bus width or compare the ext csd values of current
> + * bus width and ext csd values of 1 bit mode read earlier.
> + */
> + for (; idx>= 0; idx--) {
> +
> + /*
> + * Host is capable of 8bit transfer, then switch
> + * the device to work in 8bit transfer mode. If the
> + * mmc switch command returns error then switch to
> + * 4bit transfer mode. On success set the corresponding
> + * bus width on the host.
> + */
> + err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
> + EXT_CSD_BUS_WIDTH,
> + ext_csd_bits[idx],
> + card->ext_csd.generic_cmd6_time);
> + if (err)
> + continue;
> +
> + mmc_set_bus_width(card->host, bus_widths[idx]);
> +
> + if (!(host->caps& MMC_CAP_BUS_WIDTH_TEST))
> + err = mmc_compare_ext_csds(card, bus_widths[idx]);
> + else
> + err = mmc_bus_test(card, bus_widths[idx]);
> + if (!err)
> + break;
> + }
> +
> + /* switch to HS200 mode if bus width set successfully */
> + if (!err)
> + err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
> + EXT_CSD_HS_TIMING, 2, 0);
> +err:
> + return err;
> +}
> +
> +/*
> * Handle the detection and initialisation of a card.
> *
> * In the case of a resume, "oldcard" will contain the card
> @@ -905,11 +999,15 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
> /*
> * Activate high speed (if supported)
> */
> - if ((card->ext_csd.hs_max_dtr != 0)&&
> - (host->caps& MMC_CAP_MMC_HIGHSPEED)) {
> - err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
> - EXT_CSD_HS_TIMING, 1,
> - card->ext_csd.generic_cmd6_time);
> + if (card->ext_csd.hs_max_dtr != 0) {
> + err = 0;
> + if ((card->ext_csd.hs_max_dtr> 52000000)&&
> + (host->caps2& MMC_CAP2_HS200))
> + err = mmc_select_hs200(card);
> + else if (host->caps& MMC_CAP_MMC_HIGHSPEED)
> + err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
> + EXT_CSD_HS_TIMING, 1, 0);
> +
> if (err&& err != -EBADMSG)
> goto free_card;
>
> @@ -918,8 +1016,15 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
> mmc_hostname(card->host));
> err = 0;
> } else {
> - mmc_card_set_highspeed(card);
> - mmc_set_timing(card->host, MMC_TIMING_MMC_HS);
> + if ((card->ext_csd.hs_max_dtr> 52000000)&&
> + (host->caps2& MMC_CAP2_HS200)) {
> + mmc_card_set_hs200(card);
> + mmc_set_timing(card->host,
> + MMC_TIMING_MMC_HS200);
> + } else {
> + mmc_card_set_highspeed(card);
> + mmc_set_timing(card->host, MMC_TIMING_MMC_HS);
> + }
> }
> }
>
> @@ -944,7 +1049,7 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
> */
> max_dtr = (unsigned int)-1;
>
> - if (mmc_card_highspeed(card)) {
> + if (mmc_card_highspeed(card) || mmc_card_hs200(card)) {
> if (max_dtr> card->ext_csd.hs_max_dtr)
> max_dtr = card->ext_csd.hs_max_dtr;
> } else if (max_dtr> card->csd.max_dtr) {
> @@ -970,9 +1075,49 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
> }
>
> /*
> + * Indicate HS200 SDR mode (if supported).
> + */
> + if (mmc_card_hs200(card)) {
> + u32 ext_csd_bits;
> + u32 bus_width = card->host->ios.bus_width;
> +
> + /*
> + * For devices supporting HS200 mode, the bus width has
> + * to be set before executing the tuning function. If
> + * set before tuning, then device will respond with CRC
> + * errors for responses on CMD line. So for HS200 the
> + * sequence will be
> + * 1. set bus width 4bit / 8 bit (1 bit not supported)
> + * 2. switch to HS200 mode
> + * 3. set the clock to> 52Mhz<=200MHz and
> + * 4. execute tuning for HS200
> + */
> + if ((host->caps2& MMC_CAP2_HS200)&&
> + card->host->ops->execute_tuning)
> + err = card->host->ops->execute_tuning(card->host,
> + MMC_SEND_TUNING_BLOCK_HS200);
> + if (err) {
> + pr_warning("tuning execution failed\n");
> + goto err;
> + }
> +
> + ext_csd_bits = (bus_width == MMC_BUS_WIDTH_8) ?
> + EXT_CSD_BUS_WIDTH_8 :
> + EXT_CSD_BUS_WIDTH_4;
> + err = mmc_select_powerclass(card, ext_csd_bits, ext_csd);
> + if (err) {
> + pr_err("%s: power class selection to bus width"
> + "%d failed\n", mmc_hostname(card->host),
> + 1<< bus_width);
> + goto err;
> + }
> + }
> +
> + /*
> * Activate wide bus and DDR (if supported).
> */
> - if ((card->csd.mmca_vsn>= CSD_SPEC_VER_4)&&
> + if (!mmc_card_hs200(card)&&
> + (card->csd.mmca_vsn>= CSD_SPEC_VER_3)&&
> (host->caps& (MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA))) {
> static unsigned ext_csd_bits[][2] = {
> { EXT_CSD_BUS_WIDTH_8, EXT_CSD_DDR_BUS_WIDTH_8 },
> diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c
> index 6f27d35..a775131 100644
> --- a/drivers/mmc/core/sd.c
> +++ b/drivers/mmc/core/sd.c
> @@ -661,7 +661,8 @@ static int mmc_sd_init_uhs_card(struct mmc_card *card)
>
> /* SPI mode doesn't define CMD19 */
> if (!mmc_host_is_spi(card->host)&& card->host->ops->execute_tuning)
> - err = card->host->ops->execute_tuning(card->host);
> + err = card->host->ops->execute_tuning(card->host, \
> + MMC_SEND_TUNING_BLOCK);
>
> out:
> kfree(status);
> diff --git a/drivers/mmc/core/sdio.c b/drivers/mmc/core/sdio.c
> index b77f770..bd7bacc 100644
> --- a/drivers/mmc/core/sdio.c
> +++ b/drivers/mmc/core/sdio.c
> @@ -14,6 +14,7 @@
>
> #include<linux/mmc/host.h>
> #include<linux/mmc/card.h>
> +#include<linux/mmc/mmc.h>
> #include<linux/mmc/sdio.h>
> #include<linux/mmc/sdio_func.h>
> #include<linux/mmc/sdio_ids.h>
> @@ -556,7 +557,8 @@ static int mmc_sdio_init_uhs_card(struct mmc_card *card)
>
> /* Initialize and start re-tuning timer */
> if (!mmc_host_is_spi(card->host)&& card->host->ops->execute_tuning)
> - err = card->host->ops->execute_tuning(card->host);
> + err = card->host->ops->execute_tuning(card->host,
> + MMC_SEND_TUNING_BLOCK);
>
> out:
>
> diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h
> index 9478a6b..9f22ba5 100644
> --- a/include/linux/mmc/card.h
> +++ b/include/linux/mmc/card.h
> @@ -216,6 +216,7 @@ struct mmc_card {
> #define MMC_STATE_ULTRAHIGHSPEED (1<<5) /* card is in ultra high speed mode */
> #define MMC_CARD_SDXC (1<<6) /* card is SDXC */
> #define MMC_CARD_REMOVED (1<<7) /* card has been removed */
> +#define MMC_STATE_HIGHSPEED_200 (1<<8) /* card is in HS200 mode */
> unsigned int quirks; /* card quirks */
> #define MMC_QUIRK_LENIENT_FN0 (1<<0) /* allow SDIO FN0 writes outside of the VS CCCR range */
> #define MMC_QUIRK_BLKSZ_FOR_BYTE_MODE (1<<1) /* use func->cur_blksize */
> @@ -374,6 +375,7 @@ static inline void __maybe_unused remove_quirk(struct mmc_card *card, int data)
> #define mmc_card_present(c) ((c)->state& MMC_STATE_PRESENT)
> #define mmc_card_readonly(c) ((c)->state& MMC_STATE_READONLY)
> #define mmc_card_highspeed(c) ((c)->state& MMC_STATE_HIGHSPEED)
> +#define mmc_card_hs200(c) ((c)->state& MMC_STATE_HIGHSPEED_200)
> #define mmc_card_blockaddr(c) ((c)->state& MMC_STATE_BLOCKADDR)
> #define mmc_card_ddr_mode(c) ((c)->state& MMC_STATE_HIGHSPEED_DDR)
> #define mmc_card_uhs(c) ((c)->state& MMC_STATE_ULTRAHIGHSPEED)
> @@ -384,6 +386,7 @@ static inline void __maybe_unused remove_quirk(struct mmc_card *card, int data)
> #define mmc_card_set_present(c) ((c)->state |= MMC_STATE_PRESENT)
> #define mmc_card_set_readonly(c) ((c)->state |= MMC_STATE_READONLY)
> #define mmc_card_set_highspeed(c) ((c)->state |= MMC_STATE_HIGHSPEED)
> +#define mmc_card_set_hs200(c) ((c)->state |= MMC_STATE_HIGHSPEED_200)
> #define mmc_card_set_blockaddr(c) ((c)->state |= MMC_STATE_BLOCKADDR)
> #define mmc_card_set_ddr_mode(c) ((c)->state |= MMC_STATE_HIGHSPEED_DDR)
> #define mmc_card_set_uhs(c) ((c)->state |= MMC_STATE_ULTRAHIGHSPEED)
> diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h
> index 9a03d03..606c8c3 100644
> --- a/include/linux/mmc/host.h
> +++ b/include/linux/mmc/host.h
> @@ -56,10 +56,13 @@ struct mmc_ios {
> #define MMC_TIMING_UHS_SDR50 3
> #define MMC_TIMING_UHS_SDR104 4
> #define MMC_TIMING_UHS_DDR50 5
> +#define MMC_TIMING_MMC_HS200 6
>
> #define MMC_SDR_MODE 0
> #define MMC_1_2V_DDR_MODE 1
> #define MMC_1_8V_DDR_MODE 2
> +#define MMC_1_2V_SDR_MODE 3
> +#define MMC_1_8V_SDR_MODE 4
>
> unsigned char signal_voltage; /* signalling voltage (1.8V or 3.3V) */
>
> @@ -148,7 +151,9 @@ struct mmc_host_ops {
> void (*init_card)(struct mmc_host *host, struct mmc_card *card);
>
> int (*start_signal_voltage_switch)(struct mmc_host *host, struct mmc_ios *ios);
> - int (*execute_tuning)(struct mmc_host *host);
> +
> + /* The tuning command opcode value is different for SD and eMMC cards */
> + int (*execute_tuning)(struct mmc_host *host, u32 opcode);
> void (*enable_preset_value)(struct mmc_host *host, bool enable);
> int (*select_drive_strength)(unsigned int max_dtr, int host_drv, int card_drv);
> void (*hw_reset)(struct mmc_host *host);
> @@ -242,6 +247,10 @@ struct mmc_host {
> #define MMC_CAP2_CACHE_CTRL (1<< 1) /* Allow cache control */
> #define MMC_CAP2_POWEROFF_NOTIFY (1<< 2) /* Notify poweroff supported */
> #define MMC_CAP2_NO_MULTI_READ (1<< 3) /* Multiblock reads don't work */
> +#define MMC_CAP2_HS200_1_8V_SDR (1<< 4) /* can support */
> +#define MMC_CAP2_HS200_1_2V_SDR (1<< 5) /* can support */
> +#define MMC_CAP2_HS200 (MMC_CAP2_HS200_1_8V_SDR | \
> + MMC_CAP2_HS200_1_2V_SDR)
>
> mmc_pm_flag_t pm_caps; /* supported pm features */
> unsigned int power_notify_type;
> diff --git a/include/linux/mmc/mmc.h b/include/linux/mmc/mmc.h
> index 665548e..2c8cc69 100644
> --- a/include/linux/mmc/mmc.h
> +++ b/include/linux/mmc/mmc.h
> @@ -51,6 +51,7 @@
> #define MMC_READ_SINGLE_BLOCK 17 /* adtc [31:0] data addr R1 */
> #define MMC_READ_MULTIPLE_BLOCK 18 /* adtc [31:0] data addr R1 */
> #define MMC_SEND_TUNING_BLOCK 19 /* adtc R1 */
> +#define MMC_SEND_TUNING_BLOCK_HS200 21 /* adtc R1 */
>
> /* class 3 */
> #define MMC_WRITE_DAT_UNTIL_STOP 20 /* adtc [31:0] data addr R1 */
> @@ -339,13 +340,76 @@ struct _mmc_csd {
>
> #define EXT_CSD_CARD_TYPE_26 (1<<0) /* Card can run at 26MHz */
> #define EXT_CSD_CARD_TYPE_52 (1<<1) /* Card can run at 52MHz */
> -#define EXT_CSD_CARD_TYPE_MASK 0xF /* Mask out reserved bits */
> +#define EXT_CSD_CARD_TYPE_MASK 0x3F /* Mask out reserved bits */
> #define EXT_CSD_CARD_TYPE_DDR_1_8V (1<<2) /* Card can run at 52MHz */
> /* DDR mode @1.8V or 3V I/O */
> #define EXT_CSD_CARD_TYPE_DDR_1_2V (1<<3) /* Card can run at 52MHz */
> /* DDR mode @1.2V I/O */
> #define EXT_CSD_CARD_TYPE_DDR_52 (EXT_CSD_CARD_TYPE_DDR_1_8V \
> | EXT_CSD_CARD_TYPE_DDR_1_2V)
> +#define EXT_CSD_CARD_TYPE_SDR_1_8V (1<<4) /* Card can run at 200MHz */
> +#define EXT_CSD_CARD_TYPE_SDR_1_2V (1<<5) /* Card can run at 200MHz */
> + /* SDR mode @1.2V I/O */
> +
> +#define EXT_CSD_CARD_TYPE_SDR_200 (EXT_CSD_CARD_TYPE_SDR_1_8V \
> + | EXT_CSD_CARD_TYPE_SDR_1_2V)
> +
> +#define EXT_CSD_CARD_TYPE_SDR_ALL (EXT_CSD_CARD_TYPE_SDR_200 \
> + | EXT_CSD_CARD_TYPE_52 \
> + | EXT_CSD_CARD_TYPE_26)
> +
> +#define EXT_CSD_CARD_TYPE_SDR_1_2V_ALL (EXT_CSD_CARD_TYPE_SDR_1_2V \
> + | EXT_CSD_CARD_TYPE_52 \
> + | EXT_CSD_CARD_TYPE_26)
> +
> +#define EXT_CSD_CARD_TYPE_SDR_1_8V_ALL (EXT_CSD_CARD_TYPE_SDR_1_8V \
> + | EXT_CSD_CARD_TYPE_52 \
> + | EXT_CSD_CARD_TYPE_26)
> +
> +#define EXT_CSD_CARD_TYPE_SDR_1_2V_DDR_1_8V (EXT_CSD_CARD_TYPE_SDR_1_2V \
> + | EXT_CSD_CARD_TYPE_DDR_1_8V \
> + | EXT_CSD_CARD_TYPE_52 \
> + | EXT_CSD_CARD_TYPE_26)
> +
> +#define EXT_CSD_CARD_TYPE_SDR_1_8V_DDR_1_8V (EXT_CSD_CARD_TYPE_SDR_1_8V \
> + | EXT_CSD_CARD_TYPE_DDR_1_8V \
> + | EXT_CSD_CARD_TYPE_52 \
> + | EXT_CSD_CARD_TYPE_26)
> +
> +#define EXT_CSD_CARD_TYPE_SDR_1_2V_DDR_1_2V (EXT_CSD_CARD_TYPE_SDR_1_2V \
> + | EXT_CSD_CARD_TYPE_DDR_1_2V \
> + | EXT_CSD_CARD_TYPE_52 \
> + | EXT_CSD_CARD_TYPE_26)
> +
> +#define EXT_CSD_CARD_TYPE_SDR_1_8V_DDR_1_2V (EXT_CSD_CARD_TYPE_SDR_1_8V \
> + | EXT_CSD_CARD_TYPE_DDR_1_2V \
> + | EXT_CSD_CARD_TYPE_52 \
> + | EXT_CSD_CARD_TYPE_26)
> +
> +#define EXT_CSD_CARD_TYPE_SDR_1_2V_DDR_52 (EXT_CSD_CARD_TYPE_SDR_1_2V \
> + | EXT_CSD_CARD_TYPE_DDR_52 \
> + | EXT_CSD_CARD_TYPE_52 \
> + | EXT_CSD_CARD_TYPE_26)
> +
> +#define EXT_CSD_CARD_TYPE_SDR_1_8V_DDR_52 (EXT_CSD_CARD_TYPE_SDR_1_8V \
> + | EXT_CSD_CARD_TYPE_DDR_52 \
> + | EXT_CSD_CARD_TYPE_52 \
> + | EXT_CSD_CARD_TYPE_26)
> +
> +#define EXT_CSD_CARD_TYPE_SDR_ALL_DDR_1_8V (EXT_CSD_CARD_TYPE_SDR_200 \
> + | EXT_CSD_CARD_TYPE_DDR_1_8V \
> + | EXT_CSD_CARD_TYPE_52 \
> + | EXT_CSD_CARD_TYPE_26)
> +
> +#define EXT_CSD_CARD_TYPE_SDR_ALL_DDR_1_2V (EXT_CSD_CARD_TYPE_SDR_200 \
> + | EXT_CSD_CARD_TYPE_DDR_1_2V \
> + | EXT_CSD_CARD_TYPE_52 \
> + | EXT_CSD_CARD_TYPE_26)
> +
> +#define EXT_CSD_CARD_TYPE_SDR_ALL_DDR_52 (EXT_CSD_CARD_TYPE_SDR_200 \
> + | EXT_CSD_CARD_TYPE_DDR_52 \
> + | EXT_CSD_CARD_TYPE_52 \
> + | EXT_CSD_CARD_TYPE_26)
>
> #define EXT_CSD_BUS_WIDTH_1 0 /* Card is in 1 bit mode */
> #define EXT_CSD_BUS_WIDTH_4 1 /* Card is in 4 bit mode */
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH V8 0/2] HS200 Mode support for device and host
2011-12-23 7:12 [PATCH V8 0/2] HS200 Mode support for device and host Girish K S
2011-12-23 7:12 ` [PATCH V8 1/2] mmc: core: HS200 mode support for eMMC 4.5 Girish K S
2011-12-23 7:12 ` [PATCH V8 2/2] mmc: host: Adds support for eMMC 4.5 HS200 mode Girish K S
@ 2011-12-29 11:49 ` Girish K S
2 siblings, 0 replies; 7+ messages in thread
From: Girish K S @ 2011-12-29 11:49 UTC (permalink / raw)
To: linux-mmc
Chris,
can you add this patch series in your next pull request
On 23 December 2011 12:42, Girish K S <girish.shivananjappa@linaro.org> wrote:
> changes in v7:
> Updated with review comments for minor changes in host conditional
> handling. added the handling for 4 bit bus width.
> Changes in v6:
> split the patch into 2 and classified them as a patch for device
> and host. Modified to include the review comments.
> Changes in v5:
> Reduced the case statements for better code readability. Removed
> unused macro definitions. Modified the tuning function prototype
> and definition to support tuning for both SD and eMMC cards.
> Changes in v4:
> Rebased onto chris-mmc/mmc-next branch. This patch is successfully
> applied on commit with id de022ed3fdc14808299b2fa66dbb1ed5ab921912.
> Changes in v3:
> In the previous commits of chris-mmc/mmc-next branch, the patch with
> commit id (c0f22a2c92e357e7cb3988b0b13034d70b7461f9) defines caps2 for
> more capabilities. This patch version deletes the member ext_caps(created
> in my earlier patch) from struct mmc_host and reuses already accepted
> caps2 member.
> Changes in v2:
> Rebased to latest chris-mmc/mmc-next branch. Resolved indentation
> problems identified in review. This patch has to be applied before
> the patch released for modifying the printk messages.
> Changes in v1:
> Case statements in switch that produce same result have
> been combined to reduce repeated assignments.
> patch recreated after rebase to chris balls mmc-next branch.
>
> Girish K S (2):
> mmc: core: HS200 mode support for eMMC 4.5
> mmc: host: Adds support for eMMC 4.5 HS200 mode
>
> drivers/mmc/core/bus.c | 3 +-
> drivers/mmc/core/debugfs.c | 3 +
> drivers/mmc/core/mmc.c | 163 +++++++++++++++++++++++++++++++++++++++++---
> drivers/mmc/core/sd.c | 3 +-
> drivers/mmc/core/sdio.c | 4 +-
> drivers/mmc/host/sdhci.c | 45 +++++++++---
> drivers/mmc/host/sdhci.h | 1 +
> include/linux/mmc/card.h | 3 +
> include/linux/mmc/host.h | 11 +++-
> include/linux/mmc/mmc.h | 66 +++++++++++++++++-
> include/linux/mmc/sdhci.h | 1 +
> 11 files changed, 278 insertions(+), 25 deletions(-)
>
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH V8 1/2] mmc: core: HS200 mode support for eMMC 4.5
2011-12-23 7:12 ` [PATCH V8 1/2] mmc: core: HS200 mode support for eMMC 4.5 Girish K S
2011-12-23 9:06 ` Subhash Jadavani
@ 2012-01-02 22:51 ` Chris Ball
2012-01-03 6:14 ` Girish K S
1 sibling, 1 reply; 7+ messages in thread
From: Chris Ball @ 2012-01-02 22:51 UTC (permalink / raw)
To: Girish K S; +Cc: linux-mmc, patches, linux-samsung-soc, Philip Rakity
Hi Girish, small style comments,
On Fri, Dec 23 2011, Girish K S wrote:
> This patch adds the support of the HS200 bus speed for eMMC 4.5 devices.
> The eMMC 4.5 devices have support for 200MHz bus speed. The function
> prototype of the tuning function is modified to handle the tuning command
> number which is different in sd and mmc case.
>
> cc: Chris Ball <cjb@laptop.org>
> Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
> Signed-off-by: Philip Rakity <prakity@marvell.com>
> ---
> drivers/mmc/core/bus.c | 3 +-
> drivers/mmc/core/debugfs.c | 3 +
> drivers/mmc/core/mmc.c | 163 +++++++++++++++++++++++++++++++++++++++++---
> drivers/mmc/core/sd.c | 3 +-
> drivers/mmc/core/sdio.c | 4 +-
> include/linux/mmc/card.h | 3 +
> include/linux/mmc/host.h | 11 +++-
> include/linux/mmc/mmc.h | 66 +++++++++++++++++-
> 8 files changed, 242 insertions(+), 14 deletions(-)
>
> diff --git a/drivers/mmc/core/bus.c b/drivers/mmc/core/bus.c
> index f8a228a..5d011a3 100644
> --- a/drivers/mmc/core/bus.c
> +++ b/drivers/mmc/core/bus.c
> @@ -303,10 +303,11 @@ int mmc_add_card(struct mmc_card *card)
> mmc_card_ddr_mode(card) ? "DDR " : "",
> type);
> } else {
> - printk(KERN_INFO "%s: new %s%s%s card at address %04x\n",
> + pr_info("%s: new %s%s%s%s card at address %04x\n",
> mmc_hostname(card->host),
> mmc_card_uhs(card) ? "ultra high speed " :
> (mmc_card_highspeed(card) ? "high speed " : ""),
> + (mmc_card_hs200(card) ? "HS200 " : ""),
> mmc_card_ddr_mode(card) ? "DDR " : "",
> type, card->rca);
> }
> diff --git a/drivers/mmc/core/debugfs.c b/drivers/mmc/core/debugfs.c
> index 027615d..9ab5b17 100644
> --- a/drivers/mmc/core/debugfs.c
> +++ b/drivers/mmc/core/debugfs.c
> @@ -135,6 +135,9 @@ static int mmc_ios_show(struct seq_file *s, void *data)
> case MMC_TIMING_UHS_DDR50:
> str = "sd uhs DDR50";
> break;
> + case MMC_TIMING_MMC_HS200:
> + str = "mmc high-speed SDR200";
> + break;
> default:
> str = "invalid";
> break;
> diff --git a/drivers/mmc/core/mmc.c b/drivers/mmc/core/mmc.c
> index f0a9f1f..583cb42 100644
> --- a/drivers/mmc/core/mmc.c
> +++ b/drivers/mmc/core/mmc.c
> @@ -286,6 +286,27 @@ static int mmc_read_ext_csd(struct mmc_card *card, u8 *ext_csd)
> }
> card->ext_csd.raw_card_type = ext_csd[EXT_CSD_CARD_TYPE];
> switch (ext_csd[EXT_CSD_CARD_TYPE] & EXT_CSD_CARD_TYPE_MASK) {
> + case EXT_CSD_CARD_TYPE_SDR_ALL:
> + case EXT_CSD_CARD_TYPE_SDR_ALL_DDR_1_8V:
> + case EXT_CSD_CARD_TYPE_SDR_ALL_DDR_1_2V:
> + case EXT_CSD_CARD_TYPE_SDR_ALL_DDR_52:
> + card->ext_csd.hs_max_dtr = 200000000;
> + card->ext_csd.card_type = EXT_CSD_CARD_TYPE_SDR_200;
> + break;
> + case EXT_CSD_CARD_TYPE_SDR_1_2V_ALL:
> + case EXT_CSD_CARD_TYPE_SDR_1_2V_DDR_1_8V:
> + case EXT_CSD_CARD_TYPE_SDR_1_2V_DDR_1_2V:
> + case EXT_CSD_CARD_TYPE_SDR_1_2V_DDR_52:
> + card->ext_csd.hs_max_dtr = 200000000;
> + card->ext_csd.card_type = EXT_CSD_CARD_TYPE_SDR_1_2V;
> + break;
> + case EXT_CSD_CARD_TYPE_SDR_1_8V_ALL:
> + case EXT_CSD_CARD_TYPE_SDR_1_8V_DDR_1_8V:
> + case EXT_CSD_CARD_TYPE_SDR_1_8V_DDR_1_2V:
> + case EXT_CSD_CARD_TYPE_SDR_1_8V_DDR_52:
> + card->ext_csd.hs_max_dtr = 200000000;
> + card->ext_csd.card_type = EXT_CSD_CARD_TYPE_SDR_1_8V;
> + break;
> case EXT_CSD_CARD_TYPE_DDR_52 | EXT_CSD_CARD_TYPE_52 |
> EXT_CSD_CARD_TYPE_26:
> card->ext_csd.hs_max_dtr = 52000000;
> @@ -700,6 +721,79 @@ static int mmc_select_powerclass(struct mmc_card *card,
> }
>
> /*
> + * Selects the desired buswidth and switch to the HS200 mode
> + * if bus width set without error
> + */
> +static int mmc_select_hs200(struct mmc_card *card)
> +{
> + int idx, err = 0;
> + struct mmc_host *host;
> + static unsigned ext_csd_bits[] = {
> + EXT_CSD_BUS_WIDTH_4,
> + EXT_CSD_BUS_WIDTH_8,
> + };
> + static unsigned bus_widths[] = {
> + MMC_BUS_WIDTH_4,
> + MMC_BUS_WIDTH_8,
> + };
> +
> + BUG_ON(!card);
> +
> + host = card->host;
> +
> + if ((card->ext_csd.card_type & EXT_CSD_CARD_TYPE_SDR_1_2V)
> + && (host->caps2 & MMC_CAP2_HS200_1_2V_SDR))
A continuation (&&, ||..) should go on the end of the first line.
Also, & has higher precedence than &&, so parens are unneeded.
if (card->ext_csd.card_type & EXT_CSD_CARD_TYPE_SDR_1_2V &&
host->caps2 & MMC_CAP2_HS200_1_2V_SDR)
> + if (mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_120, 0))
> + err = mmc_set_signal_voltage(host,
> + MMC_SIGNAL_VOLTAGE_180, 0);
> +
> + /* If fails try again during next card power cycle */
> + if (err)
> + goto err;
> +
> + idx = (host->caps & MMC_CAP_8_BIT_DATA) ? 1 : 0;
Wouldn't "idx = host->caps & MMC_CAP_8_BIT_DATA;" do the same thing?
> +
> + /*
> + * Unlike SD, MMC cards dont have a configuration register to notify
> + * supported bus width. So bus test command should be run to identify
> + * the supported bus width or compare the ext csd values of current
> + * bus width and ext csd values of 1 bit mode read earlier.
> + */
> + for (; idx >= 0; idx--) {
I don't understand the purpose of this loop. idx can only be 0 or 1,
right? Why would you go through the loop more than once? Why not say
"if (idx) {"?
> +
> + /*
> + * Host is capable of 8bit transfer, then switch
> + * the device to work in 8bit transfer mode. If the
> + * mmc switch command returns error then switch to
> + * 4bit transfer mode. On success set the corresponding
> + * bus width on the host.
> + */
> + err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
> + EXT_CSD_BUS_WIDTH,
> + ext_csd_bits[idx],
> + card->ext_csd.generic_cmd6_time);
> + if (err)
> + continue;
> +
> + mmc_set_bus_width(card->host, bus_widths[idx]);
> +
> + if (!(host->caps & MMC_CAP_BUS_WIDTH_TEST))
> + err = mmc_compare_ext_csds(card, bus_widths[idx]);
> + else
> + err = mmc_bus_test(card, bus_widths[idx]);
> + if (!err)
> + break;
> + }
> +
> + /* switch to HS200 mode if bus width set successfully */
> + if (!err)
> + err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
> + EXT_CSD_HS_TIMING, 2, 0);
> +err:
> + return err;
> +}
> +
> +/*
> * Handle the detection and initialisation of a card.
> *
> * In the case of a resume, "oldcard" will contain the card
> @@ -905,11 +999,15 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
> /*
> * Activate high speed (if supported)
> */
> - if ((card->ext_csd.hs_max_dtr != 0) &&
> - (host->caps & MMC_CAP_MMC_HIGHSPEED)) {
> - err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
> - EXT_CSD_HS_TIMING, 1,
> - card->ext_csd.generic_cmd6_time);
> + if (card->ext_csd.hs_max_dtr != 0) {
> + err = 0;
> + if ((card->ext_csd.hs_max_dtr > 52000000) &&
> + (host->caps2 & MMC_CAP2_HS200))
No need for these parentheses.
if (card->ext_csd.hs_max_dtr > 52000000 &&
host->caps2 & MMC_CAP2_HS200)
> + err = mmc_select_hs200(card);
> + else if (host->caps & MMC_CAP_MMC_HIGHSPEED)
> + err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
> + EXT_CSD_HS_TIMING, 1, 0);
> +
> if (err && err != -EBADMSG)
> goto free_card;
>
> @@ -918,8 +1016,15 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
> mmc_hostname(card->host));
> err = 0;
> } else {
> - mmc_card_set_highspeed(card);
> - mmc_set_timing(card->host, MMC_TIMING_MMC_HS);
> + if ((card->ext_csd.hs_max_dtr > 52000000) &&
> + (host->caps2 & MMC_CAP2_HS200)) {
Same as above.
> + mmc_card_set_hs200(card);
> + mmc_set_timing(card->host,
> + MMC_TIMING_MMC_HS200);
> + } else {
> + mmc_card_set_highspeed(card);
> + mmc_set_timing(card->host, MMC_TIMING_MMC_HS);
> + }
> }
> }
>
> @@ -944,7 +1049,7 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
> */
> max_dtr = (unsigned int)-1;
>
> - if (mmc_card_highspeed(card)) {
> + if (mmc_card_highspeed(card) || mmc_card_hs200(card)) {
> if (max_dtr > card->ext_csd.hs_max_dtr)
> max_dtr = card->ext_csd.hs_max_dtr;
> } else if (max_dtr > card->csd.max_dtr) {
> @@ -970,9 +1075,49 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
> }
>
> /*
> + * Indicate HS200 SDR mode (if supported).
> + */
> + if (mmc_card_hs200(card)) {
> + u32 ext_csd_bits;
> + u32 bus_width = card->host->ios.bus_width;
> +
> + /*
> + * For devices supporting HS200 mode, the bus width has
> + * to be set before executing the tuning function. If
> + * set before tuning, then device will respond with CRC
> + * errors for responses on CMD line. So for HS200 the
> + * sequence will be
> + * 1. set bus width 4bit / 8 bit (1 bit not supported)
> + * 2. switch to HS200 mode
> + * 3. set the clock to > 52Mhz <=200MHz and
> + * 4. execute tuning for HS200
> + */
> + if ((host->caps2 & MMC_CAP2_HS200) &&
> + card->host->ops->execute_tuning)
> + err = card->host->ops->execute_tuning(card->host,
> + MMC_SEND_TUNING_BLOCK_HS200);
One less tab here.
> + if (err) {
> + pr_warning("tuning execution failed\n");
> + goto err;
> + }
Add the mmc_hostname().
> +
> + ext_csd_bits = (bus_width == MMC_BUS_WIDTH_8) ?
> + EXT_CSD_BUS_WIDTH_8 :
> + EXT_CSD_BUS_WIDTH_4;
ext_csd_bits = (bus_width == MMC_BUS_WIDTH_8) ?
EXT_CSD_BUS_WIDTH_8 : EXT_CSD_BUS_WIDTH_4;
> + err = mmc_select_powerclass(card, ext_csd_bits, ext_csd);
> + if (err) {
> + pr_err("%s: power class selection to bus width"
> + "%d failed\n", mmc_hostname(card->host),
> + 1 << bus_width);
I think using one line for the format string is okay here, even though
it will go past 80 chars. It's easier to grep for strings that way.
pr_err("%s: power class selection to bus width %d failed\n",
mmc_hostname(card->host), 1 << bus_width);
> + goto err;
> + }
> + }
> +
> + /*
> * Activate wide bus and DDR (if supported).
> */
> - if ((card->csd.mmca_vsn >= CSD_SPEC_VER_4) &&
> + if (!mmc_card_hs200(card) &&
> + (card->csd.mmca_vsn >= CSD_SPEC_VER_3) &&
> (host->caps & (MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA))) {
> static unsigned ext_csd_bits[][2] = {
> { EXT_CSD_BUS_WIDTH_8, EXT_CSD_DDR_BUS_WIDTH_8 },
> diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c
> index 6f27d35..a775131 100644
> --- a/drivers/mmc/core/sd.c
> +++ b/drivers/mmc/core/sd.c
> @@ -661,7 +661,8 @@ static int mmc_sd_init_uhs_card(struct mmc_card *card)
>
> /* SPI mode doesn't define CMD19 */
> if (!mmc_host_is_spi(card->host) && card->host->ops->execute_tuning)
> - err = card->host->ops->execute_tuning(card->host);
> + err = card->host->ops->execute_tuning(card->host, \
> + MMC_SEND_TUNING_BLOCK);
\ is unnecessary here.
>
> out:
> kfree(status);
> diff --git a/drivers/mmc/core/sdio.c b/drivers/mmc/core/sdio.c
> index b77f770..bd7bacc 100644
> --- a/drivers/mmc/core/sdio.c
> +++ b/drivers/mmc/core/sdio.c
> @@ -14,6 +14,7 @@
>
> #include <linux/mmc/host.h>
> #include <linux/mmc/card.h>
> +#include <linux/mmc/mmc.h>
> #include <linux/mmc/sdio.h>
> #include <linux/mmc/sdio_func.h>
> #include <linux/mmc/sdio_ids.h>
> @@ -556,7 +557,8 @@ static int mmc_sdio_init_uhs_card(struct mmc_card *card)
>
> /* Initialize and start re-tuning timer */
> if (!mmc_host_is_spi(card->host) && card->host->ops->execute_tuning)
> - err = card->host->ops->execute_tuning(card->host);
> + err = card->host->ops->execute_tuning(card->host,
> + MMC_SEND_TUNING_BLOCK);
>
> out:
>
> diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h
> index 9478a6b..9f22ba5 100644
> --- a/include/linux/mmc/card.h
> +++ b/include/linux/mmc/card.h
> @@ -216,6 +216,7 @@ struct mmc_card {
> #define MMC_STATE_ULTRAHIGHSPEED (1<<5) /* card is in ultra high speed mode */
> #define MMC_CARD_SDXC (1<<6) /* card is SDXC */
> #define MMC_CARD_REMOVED (1<<7) /* card has been removed */
> +#define MMC_STATE_HIGHSPEED_200 (1<<8) /* card is in HS200 mode */
> unsigned int quirks; /* card quirks */
> #define MMC_QUIRK_LENIENT_FN0 (1<<0) /* allow SDIO FN0 writes outside of the VS CCCR range */
> #define MMC_QUIRK_BLKSZ_FOR_BYTE_MODE (1<<1) /* use func->cur_blksize */
> @@ -374,6 +375,7 @@ static inline void __maybe_unused remove_quirk(struct mmc_card *card, int data)
> #define mmc_card_present(c) ((c)->state & MMC_STATE_PRESENT)
> #define mmc_card_readonly(c) ((c)->state & MMC_STATE_READONLY)
> #define mmc_card_highspeed(c) ((c)->state & MMC_STATE_HIGHSPEED)
> +#define mmc_card_hs200(c) ((c)->state & MMC_STATE_HIGHSPEED_200)
> #define mmc_card_blockaddr(c) ((c)->state & MMC_STATE_BLOCKADDR)
> #define mmc_card_ddr_mode(c) ((c)->state & MMC_STATE_HIGHSPEED_DDR)
> #define mmc_card_uhs(c) ((c)->state & MMC_STATE_ULTRAHIGHSPEED)
> @@ -384,6 +386,7 @@ static inline void __maybe_unused remove_quirk(struct mmc_card *card, int data)
> #define mmc_card_set_present(c) ((c)->state |= MMC_STATE_PRESENT)
> #define mmc_card_set_readonly(c) ((c)->state |= MMC_STATE_READONLY)
> #define mmc_card_set_highspeed(c) ((c)->state |= MMC_STATE_HIGHSPEED)
> +#define mmc_card_set_hs200(c) ((c)->state |= MMC_STATE_HIGHSPEED_200)
> #define mmc_card_set_blockaddr(c) ((c)->state |= MMC_STATE_BLOCKADDR)
> #define mmc_card_set_ddr_mode(c) ((c)->state |= MMC_STATE_HIGHSPEED_DDR)
> #define mmc_card_set_uhs(c) ((c)->state |= MMC_STATE_ULTRAHIGHSPEED)
> diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h
> index 9a03d03..606c8c3 100644
> --- a/include/linux/mmc/host.h
> +++ b/include/linux/mmc/host.h
> @@ -56,10 +56,13 @@ struct mmc_ios {
> #define MMC_TIMING_UHS_SDR50 3
> #define MMC_TIMING_UHS_SDR104 4
> #define MMC_TIMING_UHS_DDR50 5
> +#define MMC_TIMING_MMC_HS200 6
>
> #define MMC_SDR_MODE 0
> #define MMC_1_2V_DDR_MODE 1
> #define MMC_1_8V_DDR_MODE 2
> +#define MMC_1_2V_SDR_MODE 3
> +#define MMC_1_8V_SDR_MODE 4
>
> unsigned char signal_voltage; /* signalling voltage (1.8V or 3.3V) */
>
> @@ -148,7 +151,9 @@ struct mmc_host_ops {
> void (*init_card)(struct mmc_host *host, struct mmc_card *card);
>
> int (*start_signal_voltage_switch)(struct mmc_host *host, struct mmc_ios *ios);
> - int (*execute_tuning)(struct mmc_host *host);
> +
> + /* The tuning command opcode value is different for SD and eMMC cards */
> + int (*execute_tuning)(struct mmc_host *host, u32 opcode);
> void (*enable_preset_value)(struct mmc_host *host, bool enable);
> int (*select_drive_strength)(unsigned int max_dtr, int host_drv, int card_drv);
> void (*hw_reset)(struct mmc_host *host);
> @@ -242,6 +247,10 @@ struct mmc_host {
> #define MMC_CAP2_CACHE_CTRL (1 << 1) /* Allow cache control */
> #define MMC_CAP2_POWEROFF_NOTIFY (1 << 2) /* Notify poweroff supported */
> #define MMC_CAP2_NO_MULTI_READ (1 << 3) /* Multiblock reads don't work */
> +#define MMC_CAP2_HS200_1_8V_SDR (1 << 4) /* can support */
> +#define MMC_CAP2_HS200_1_2V_SDR (1 << 5) /* can support */
> +#define MMC_CAP2_HS200 (MMC_CAP2_HS200_1_8V_SDR | \
> + MMC_CAP2_HS200_1_2V_SDR)
>
> mmc_pm_flag_t pm_caps; /* supported pm features */
> unsigned int power_notify_type;
> diff --git a/include/linux/mmc/mmc.h b/include/linux/mmc/mmc.h
> index 665548e..2c8cc69 100644
> --- a/include/linux/mmc/mmc.h
> +++ b/include/linux/mmc/mmc.h
> @@ -51,6 +51,7 @@
> #define MMC_READ_SINGLE_BLOCK 17 /* adtc [31:0] data addr R1 */
> #define MMC_READ_MULTIPLE_BLOCK 18 /* adtc [31:0] data addr R1 */
> #define MMC_SEND_TUNING_BLOCK 19 /* adtc R1 */
> +#define MMC_SEND_TUNING_BLOCK_HS200 21 /* adtc R1 */
>
> /* class 3 */
> #define MMC_WRITE_DAT_UNTIL_STOP 20 /* adtc [31:0] data addr R1 */
> @@ -339,13 +340,76 @@ struct _mmc_csd {
>
> #define EXT_CSD_CARD_TYPE_26 (1<<0) /* Card can run at 26MHz */
> #define EXT_CSD_CARD_TYPE_52 (1<<1) /* Card can run at 52MHz */
> -#define EXT_CSD_CARD_TYPE_MASK 0xF /* Mask out reserved bits */
> +#define EXT_CSD_CARD_TYPE_MASK 0x3F /* Mask out reserved bits */
> #define EXT_CSD_CARD_TYPE_DDR_1_8V (1<<2) /* Card can run at 52MHz */
> /* DDR mode @1.8V or 3V I/O */
> #define EXT_CSD_CARD_TYPE_DDR_1_2V (1<<3) /* Card can run at 52MHz */
> /* DDR mode @1.2V I/O */
> #define EXT_CSD_CARD_TYPE_DDR_52 (EXT_CSD_CARD_TYPE_DDR_1_8V \
> | EXT_CSD_CARD_TYPE_DDR_1_2V)
> +#define EXT_CSD_CARD_TYPE_SDR_1_8V (1<<4) /* Card can run at 200MHz */
> +#define EXT_CSD_CARD_TYPE_SDR_1_2V (1<<5) /* Card can run at 200MHz */
> + /* SDR mode @1.2V I/O */
> +
> +#define EXT_CSD_CARD_TYPE_SDR_200 (EXT_CSD_CARD_TYPE_SDR_1_8V \
> + | EXT_CSD_CARD_TYPE_SDR_1_2V)
> +
Normal kernel coding style is:
#define EXT_CSD_CARD_TYPE_SDR_200 (EXT_CSD_CARD_TYPE_SDR_1_8V | \
EXT_CSD_CARD_TYPE_SDR_1_2V)
> +#define EXT_CSD_CARD_TYPE_SDR_ALL (EXT_CSD_CARD_TYPE_SDR_200 \
> + | EXT_CSD_CARD_TYPE_52 \
> + | EXT_CSD_CARD_TYPE_26)
> +
> +#define EXT_CSD_CARD_TYPE_SDR_1_2V_ALL (EXT_CSD_CARD_TYPE_SDR_1_2V \
> + | EXT_CSD_CARD_TYPE_52 \
> + | EXT_CSD_CARD_TYPE_26)
> +
> +#define EXT_CSD_CARD_TYPE_SDR_1_8V_ALL (EXT_CSD_CARD_TYPE_SDR_1_8V \
> + | EXT_CSD_CARD_TYPE_52 \
> + | EXT_CSD_CARD_TYPE_26)
> +
> +#define EXT_CSD_CARD_TYPE_SDR_1_2V_DDR_1_8V (EXT_CSD_CARD_TYPE_SDR_1_2V \
> + | EXT_CSD_CARD_TYPE_DDR_1_8V \
> + | EXT_CSD_CARD_TYPE_52 \
> + | EXT_CSD_CARD_TYPE_26)
> +
> +#define EXT_CSD_CARD_TYPE_SDR_1_8V_DDR_1_8V (EXT_CSD_CARD_TYPE_SDR_1_8V \
> + | EXT_CSD_CARD_TYPE_DDR_1_8V \
> + | EXT_CSD_CARD_TYPE_52 \
> + | EXT_CSD_CARD_TYPE_26)
> +
> +#define EXT_CSD_CARD_TYPE_SDR_1_2V_DDR_1_2V (EXT_CSD_CARD_TYPE_SDR_1_2V \
> + | EXT_CSD_CARD_TYPE_DDR_1_2V \
> + | EXT_CSD_CARD_TYPE_52 \
> + | EXT_CSD_CARD_TYPE_26)
> +
> +#define EXT_CSD_CARD_TYPE_SDR_1_8V_DDR_1_2V (EXT_CSD_CARD_TYPE_SDR_1_8V \
> + | EXT_CSD_CARD_TYPE_DDR_1_2V \
> + | EXT_CSD_CARD_TYPE_52 \
> + | EXT_CSD_CARD_TYPE_26)
> +
> +#define EXT_CSD_CARD_TYPE_SDR_1_2V_DDR_52 (EXT_CSD_CARD_TYPE_SDR_1_2V \
> + | EXT_CSD_CARD_TYPE_DDR_52 \
> + | EXT_CSD_CARD_TYPE_52 \
> + | EXT_CSD_CARD_TYPE_26)
> +
> +#define EXT_CSD_CARD_TYPE_SDR_1_8V_DDR_52 (EXT_CSD_CARD_TYPE_SDR_1_8V \
> + | EXT_CSD_CARD_TYPE_DDR_52 \
> + | EXT_CSD_CARD_TYPE_52 \
> + | EXT_CSD_CARD_TYPE_26)
> +
> +#define EXT_CSD_CARD_TYPE_SDR_ALL_DDR_1_8V (EXT_CSD_CARD_TYPE_SDR_200 \
> + | EXT_CSD_CARD_TYPE_DDR_1_8V \
> + | EXT_CSD_CARD_TYPE_52 \
> + | EXT_CSD_CARD_TYPE_26)
> +
> +#define EXT_CSD_CARD_TYPE_SDR_ALL_DDR_1_2V (EXT_CSD_CARD_TYPE_SDR_200 \
> + | EXT_CSD_CARD_TYPE_DDR_1_2V \
> + | EXT_CSD_CARD_TYPE_52 \
> + | EXT_CSD_CARD_TYPE_26)
> +
> +#define EXT_CSD_CARD_TYPE_SDR_ALL_DDR_52 (EXT_CSD_CARD_TYPE_SDR_200 \
> + | EXT_CSD_CARD_TYPE_DDR_52 \
> + | EXT_CSD_CARD_TYPE_52 \
> + | EXT_CSD_CARD_TYPE_26)
>
> #define EXT_CSD_BUS_WIDTH_1 0 /* Card is in 1 bit mode */
> #define EXT_CSD_BUS_WIDTH_4 1 /* Card is in 4 bit mode */
Thanks,
- Chris.
--
Chris Ball <cjb@laptop.org> <http://printf.net/>
One Laptop Per Child
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH V8 1/2] mmc: core: HS200 mode support for eMMC 4.5
2012-01-02 22:51 ` Chris Ball
@ 2012-01-03 6:14 ` Girish K S
0 siblings, 0 replies; 7+ messages in thread
From: Girish K S @ 2012-01-03 6:14 UTC (permalink / raw)
To: Chris Ball; +Cc: linux-mmc, patches, linux-samsung-soc, Philip Rakity
On 3 January 2012 04:21, Chris Ball <cjb@laptop.org> wrote:
> Hi Girish, small style comments,
>
> On Fri, Dec 23 2011, Girish K S wrote:
>> This patch adds the support of the HS200 bus speed for eMMC 4.5 devices.
>> The eMMC 4.5 devices have support for 200MHz bus speed. The function
>> prototype of the tuning function is modified to handle the tuning command
>> number which is different in sd and mmc case.
>>
>> cc: Chris Ball <cjb@laptop.org>
>> Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
>> Signed-off-by: Philip Rakity <prakity@marvell.com>
>> ---
>> drivers/mmc/core/bus.c | 3 +-
>> drivers/mmc/core/debugfs.c | 3 +
>> drivers/mmc/core/mmc.c | 163 +++++++++++++++++++++++++++++++++++++++++---
>> drivers/mmc/core/sd.c | 3 +-
>> drivers/mmc/core/sdio.c | 4 +-
>> include/linux/mmc/card.h | 3 +
>> include/linux/mmc/host.h | 11 +++-
>> include/linux/mmc/mmc.h | 66 +++++++++++++++++-
>> 8 files changed, 242 insertions(+), 14 deletions(-)
>>
>> diff --git a/drivers/mmc/core/bus.c b/drivers/mmc/core/bus.c
>> index f8a228a..5d011a3 100644
>> --- a/drivers/mmc/core/bus.c
>> +++ b/drivers/mmc/core/bus.c
>> @@ -303,10 +303,11 @@ int mmc_add_card(struct mmc_card *card)
>> mmc_card_ddr_mode(card) ? "DDR " : "",
>> type);
>> } else {
>> - printk(KERN_INFO "%s: new %s%s%s card at address %04x\n",
>> + pr_info("%s: new %s%s%s%s card at address %04x\n",
>> mmc_hostname(card->host),
>> mmc_card_uhs(card) ? "ultra high speed " :
>> (mmc_card_highspeed(card) ? "high speed " : ""),
>> + (mmc_card_hs200(card) ? "HS200 " : ""),
>> mmc_card_ddr_mode(card) ? "DDR " : "",
>> type, card->rca);
>> }
>> diff --git a/drivers/mmc/core/debugfs.c b/drivers/mmc/core/debugfs.c
>> index 027615d..9ab5b17 100644
>> --- a/drivers/mmc/core/debugfs.c
>> +++ b/drivers/mmc/core/debugfs.c
>> @@ -135,6 +135,9 @@ static int mmc_ios_show(struct seq_file *s, void *data)
>> case MMC_TIMING_UHS_DDR50:
>> str = "sd uhs DDR50";
>> break;
>> + case MMC_TIMING_MMC_HS200:
>> + str = "mmc high-speed SDR200";
>> + break;
>> default:
>> str = "invalid";
>> break;
>> diff --git a/drivers/mmc/core/mmc.c b/drivers/mmc/core/mmc.c
>> index f0a9f1f..583cb42 100644
>> --- a/drivers/mmc/core/mmc.c
>> +++ b/drivers/mmc/core/mmc.c
>> @@ -286,6 +286,27 @@ static int mmc_read_ext_csd(struct mmc_card *card, u8 *ext_csd)
>> }
>> card->ext_csd.raw_card_type = ext_csd[EXT_CSD_CARD_TYPE];
>> switch (ext_csd[EXT_CSD_CARD_TYPE] & EXT_CSD_CARD_TYPE_MASK) {
>> + case EXT_CSD_CARD_TYPE_SDR_ALL:
>> + case EXT_CSD_CARD_TYPE_SDR_ALL_DDR_1_8V:
>> + case EXT_CSD_CARD_TYPE_SDR_ALL_DDR_1_2V:
>> + case EXT_CSD_CARD_TYPE_SDR_ALL_DDR_52:
>> + card->ext_csd.hs_max_dtr = 200000000;
>> + card->ext_csd.card_type = EXT_CSD_CARD_TYPE_SDR_200;
>> + break;
>> + case EXT_CSD_CARD_TYPE_SDR_1_2V_ALL:
>> + case EXT_CSD_CARD_TYPE_SDR_1_2V_DDR_1_8V:
>> + case EXT_CSD_CARD_TYPE_SDR_1_2V_DDR_1_2V:
>> + case EXT_CSD_CARD_TYPE_SDR_1_2V_DDR_52:
>> + card->ext_csd.hs_max_dtr = 200000000;
>> + card->ext_csd.card_type = EXT_CSD_CARD_TYPE_SDR_1_2V;
>> + break;
>> + case EXT_CSD_CARD_TYPE_SDR_1_8V_ALL:
>> + case EXT_CSD_CARD_TYPE_SDR_1_8V_DDR_1_8V:
>> + case EXT_CSD_CARD_TYPE_SDR_1_8V_DDR_1_2V:
>> + case EXT_CSD_CARD_TYPE_SDR_1_8V_DDR_52:
>> + card->ext_csd.hs_max_dtr = 200000000;
>> + card->ext_csd.card_type = EXT_CSD_CARD_TYPE_SDR_1_8V;
>> + break;
>> case EXT_CSD_CARD_TYPE_DDR_52 | EXT_CSD_CARD_TYPE_52 |
>> EXT_CSD_CARD_TYPE_26:
>> card->ext_csd.hs_max_dtr = 52000000;
>> @@ -700,6 +721,79 @@ static int mmc_select_powerclass(struct mmc_card *card,
>> }
>>
>> /*
>> + * Selects the desired buswidth and switch to the HS200 mode
>> + * if bus width set without error
>> + */
>> +static int mmc_select_hs200(struct mmc_card *card)
>> +{
>> + int idx, err = 0;
>> + struct mmc_host *host;
>> + static unsigned ext_csd_bits[] = {
>> + EXT_CSD_BUS_WIDTH_4,
>> + EXT_CSD_BUS_WIDTH_8,
>> + };
>> + static unsigned bus_widths[] = {
>> + MMC_BUS_WIDTH_4,
>> + MMC_BUS_WIDTH_8,
>> + };
>> +
>> + BUG_ON(!card);
>> +
>> + host = card->host;
>> +
>> + if ((card->ext_csd.card_type & EXT_CSD_CARD_TYPE_SDR_1_2V)
>> + && (host->caps2 & MMC_CAP2_HS200_1_2V_SDR))
>
> A continuation (&&, ||..) should go on the end of the first line.
> Also, & has higher precedence than &&, so parens are unneeded.
>
> if (card->ext_csd.card_type & EXT_CSD_CARD_TYPE_SDR_1_2V &&
> host->caps2 & MMC_CAP2_HS200_1_2V_SDR)
Will Update it
>
>> + if (mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_120, 0))
>> + err = mmc_set_signal_voltage(host,
>> + MMC_SIGNAL_VOLTAGE_180, 0);
>> +
>> + /* If fails try again during next card power cycle */
>> + if (err)
>> + goto err;
>> +
>> + idx = (host->caps & MMC_CAP_8_BIT_DATA) ? 1 : 0;
>
> Wouldn't "idx = host->caps & MMC_CAP_8_BIT_DATA;" do the same thing?
host->caps & MMC_CAP_8_BIT_DATA will assign (1 << 6) or 0 to idx. But
i want to assign 0 or 1.
>
>> +
>> + /*
>> + * Unlike SD, MMC cards dont have a configuration register to notify
>> + * supported bus width. So bus test command should be run to identify
>> + * the supported bus width or compare the ext csd values of current
>> + * bus width and ext csd values of 1 bit mode read earlier.
>> + */
>> + for (; idx >= 0; idx--) {
>
> I don't understand the purpose of this loop. idx can only be 0 or 1,
> right? Why would you go through the loop more than once? Why not say
> "if (idx) {"?
>
idx value will only indicate whether host is capable of handling 8 bit
and 4 bit mode.
To validate whether card supports 8/4
1. the driver code should switch to 8 bit mode (highest bus
supported), execute the bus test. If successful then continue with the
8 bit mode.
2. If bus test fails for 8 bit mode then continue step 1 with 4 bit mode.
due to this reason we need to go through the loop for more than once.
>> +
>> + /*
>> + * Host is capable of 8bit transfer, then switch
>> + * the device to work in 8bit transfer mode. If the
>> + * mmc switch command returns error then switch to
>> + * 4bit transfer mode. On success set the corresponding
>> + * bus width on the host.
>> + */
>> + err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
>> + EXT_CSD_BUS_WIDTH,
>> + ext_csd_bits[idx],
>> + card->ext_csd.generic_cmd6_time);
>> + if (err)
>> + continue;
>> +
>> + mmc_set_bus_width(card->host, bus_widths[idx]);
>> +
>> + if (!(host->caps & MMC_CAP_BUS_WIDTH_TEST))
>> + err = mmc_compare_ext_csds(card, bus_widths[idx]);
>> + else
>> + err = mmc_bus_test(card, bus_widths[idx]);
>> + if (!err)
>> + break;
>> + }
>> +
>> + /* switch to HS200 mode if bus width set successfully */
>> + if (!err)
>> + err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
>> + EXT_CSD_HS_TIMING, 2, 0);
>> +err:
>> + return err;
>> +}
>> +
>> +/*
>> * Handle the detection and initialisation of a card.
>> *
>> * In the case of a resume, "oldcard" will contain the card
>> @@ -905,11 +999,15 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
>> /*
>> * Activate high speed (if supported)
>> */
>> - if ((card->ext_csd.hs_max_dtr != 0) &&
>> - (host->caps & MMC_CAP_MMC_HIGHSPEED)) {
>> - err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
>> - EXT_CSD_HS_TIMING, 1,
>> - card->ext_csd.generic_cmd6_time);
>> + if (card->ext_csd.hs_max_dtr != 0) {
>> + err = 0;
>> + if ((card->ext_csd.hs_max_dtr > 52000000) &&
>> + (host->caps2 & MMC_CAP2_HS200))
>
> No need for these parentheses.
agree will update in next patch
>
> if (card->ext_csd.hs_max_dtr > 52000000 &&
> host->caps2 & MMC_CAP2_HS200)
>
>> + err = mmc_select_hs200(card);
>> + else if (host->caps & MMC_CAP_MMC_HIGHSPEED)
>> + err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
>> + EXT_CSD_HS_TIMING, 1, 0);
>> +
>> if (err && err != -EBADMSG)
>> goto free_card;
>>
>> @@ -918,8 +1016,15 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
>> mmc_hostname(card->host));
>> err = 0;
>> } else {
>> - mmc_card_set_highspeed(card);
>> - mmc_set_timing(card->host, MMC_TIMING_MMC_HS);
>> + if ((card->ext_csd.hs_max_dtr > 52000000) &&
>> + (host->caps2 & MMC_CAP2_HS200)) {
>
> Same as above.
>
agree will update in next patch
>> + mmc_card_set_hs200(card);
>> + mmc_set_timing(card->host,
>> + MMC_TIMING_MMC_HS200);
>> + } else {
>> + mmc_card_set_highspeed(card);
>> + mmc_set_timing(card->host, MMC_TIMING_MMC_HS);
>> + }
>> }
>> }
>>
>> @@ -944,7 +1049,7 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
>> */
>> max_dtr = (unsigned int)-1;
>>
>> - if (mmc_card_highspeed(card)) {
>> + if (mmc_card_highspeed(card) || mmc_card_hs200(card)) {
>> if (max_dtr > card->ext_csd.hs_max_dtr)
>> max_dtr = card->ext_csd.hs_max_dtr;
>> } else if (max_dtr > card->csd.max_dtr) {
>> @@ -970,9 +1075,49 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
>> }
>>
>> /*
>> + * Indicate HS200 SDR mode (if supported).
>> + */
>> + if (mmc_card_hs200(card)) {
>> + u32 ext_csd_bits;
>> + u32 bus_width = card->host->ios.bus_width;
>> +
>> + /*
>> + * For devices supporting HS200 mode, the bus width has
>> + * to be set before executing the tuning function. If
>> + * set before tuning, then device will respond with CRC
>> + * errors for responses on CMD line. So for HS200 the
>> + * sequence will be
>> + * 1. set bus width 4bit / 8 bit (1 bit not supported)
>> + * 2. switch to HS200 mode
>> + * 3. set the clock to > 52Mhz <=200MHz and
>> + * 4. execute tuning for HS200
>> + */
>> + if ((host->caps2 & MMC_CAP2_HS200) &&
>> + card->host->ops->execute_tuning)
>> + err = card->host->ops->execute_tuning(card->host,
>> + MMC_SEND_TUNING_BLOCK_HS200);
>
> One less tab here.
>
agree will update in next patch
>> + if (err) {
>> + pr_warning("tuning execution failed\n");
>> + goto err;
>> + }
>
> Add the mmc_hostname().
>
agree will update in next patch
>> +
>> + ext_csd_bits = (bus_width == MMC_BUS_WIDTH_8) ?
>> + EXT_CSD_BUS_WIDTH_8 :
>> + EXT_CSD_BUS_WIDTH_4;
>
> ext_csd_bits = (bus_width == MMC_BUS_WIDTH_8) ?
> EXT_CSD_BUS_WIDTH_8 : EXT_CSD_BUS_WIDTH_4;
>
agree will update in next patch
>> + err = mmc_select_powerclass(card, ext_csd_bits, ext_csd);
>> + if (err) {
>> + pr_err("%s: power class selection to bus width"
>> + "%d failed\n", mmc_hostname(card->host),
>> + 1 << bus_width);
>
> I think using one line for the format string is okay here, even though
> it will go past 80 chars. It's easier to grep for strings that way.
>
> pr_err("%s: power class selection to bus width %d failed\n",
> mmc_hostname(card->host), 1 << bus_width);
>
agree will update in next patch
>> + goto err;
>> + }
>> + }
>> +
>> + /*
>> * Activate wide bus and DDR (if supported).
>> */
>> - if ((card->csd.mmca_vsn >= CSD_SPEC_VER_4) &&
>> + if (!mmc_card_hs200(card) &&
>> + (card->csd.mmca_vsn >= CSD_SPEC_VER_3) &&
>> (host->caps & (MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA))) {
>> static unsigned ext_csd_bits[][2] = {
>> { EXT_CSD_BUS_WIDTH_8, EXT_CSD_DDR_BUS_WIDTH_8 },
>> diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c
>> index 6f27d35..a775131 100644
>> --- a/drivers/mmc/core/sd.c
>> +++ b/drivers/mmc/core/sd.c
>> @@ -661,7 +661,8 @@ static int mmc_sd_init_uhs_card(struct mmc_card *card)
>>
>> /* SPI mode doesn't define CMD19 */
>> if (!mmc_host_is_spi(card->host) && card->host->ops->execute_tuning)
>> - err = card->host->ops->execute_tuning(card->host);
>> + err = card->host->ops->execute_tuning(card->host, \
>> + MMC_SEND_TUNING_BLOCK);
>
> \ is unnecessary here.
>
OK agree
>>
>> out:
>> kfree(status);
>> diff --git a/drivers/mmc/core/sdio.c b/drivers/mmc/core/sdio.c
>> index b77f770..bd7bacc 100644
>> --- a/drivers/mmc/core/sdio.c
>> +++ b/drivers/mmc/core/sdio.c
>> @@ -14,6 +14,7 @@
>>
>> #include <linux/mmc/host.h>
>> #include <linux/mmc/card.h>
>> +#include <linux/mmc/mmc.h>
>> #include <linux/mmc/sdio.h>
>> #include <linux/mmc/sdio_func.h>
>> #include <linux/mmc/sdio_ids.h>
>> @@ -556,7 +557,8 @@ static int mmc_sdio_init_uhs_card(struct mmc_card *card)
>>
>> /* Initialize and start re-tuning timer */
>> if (!mmc_host_is_spi(card->host) && card->host->ops->execute_tuning)
>> - err = card->host->ops->execute_tuning(card->host);
>> + err = card->host->ops->execute_tuning(card->host,
>> + MMC_SEND_TUNING_BLOCK);
>>
>> out:
>>
>> diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h
>> index 9478a6b..9f22ba5 100644
>> --- a/include/linux/mmc/card.h
>> +++ b/include/linux/mmc/card.h
>> @@ -216,6 +216,7 @@ struct mmc_card {
>> #define MMC_STATE_ULTRAHIGHSPEED (1<<5) /* card is in ultra high speed mode */
>> #define MMC_CARD_SDXC (1<<6) /* card is SDXC */
>> #define MMC_CARD_REMOVED (1<<7) /* card has been removed */
>> +#define MMC_STATE_HIGHSPEED_200 (1<<8) /* card is in HS200 mode */
>> unsigned int quirks; /* card quirks */
>> #define MMC_QUIRK_LENIENT_FN0 (1<<0) /* allow SDIO FN0 writes outside of the VS CCCR range */
>> #define MMC_QUIRK_BLKSZ_FOR_BYTE_MODE (1<<1) /* use func->cur_blksize */
>> @@ -374,6 +375,7 @@ static inline void __maybe_unused remove_quirk(struct mmc_card *card, int data)
>> #define mmc_card_present(c) ((c)->state & MMC_STATE_PRESENT)
>> #define mmc_card_readonly(c) ((c)->state & MMC_STATE_READONLY)
>> #define mmc_card_highspeed(c) ((c)->state & MMC_STATE_HIGHSPEED)
>> +#define mmc_card_hs200(c) ((c)->state & MMC_STATE_HIGHSPEED_200)
>> #define mmc_card_blockaddr(c) ((c)->state & MMC_STATE_BLOCKADDR)
>> #define mmc_card_ddr_mode(c) ((c)->state & MMC_STATE_HIGHSPEED_DDR)
>> #define mmc_card_uhs(c) ((c)->state & MMC_STATE_ULTRAHIGHSPEED)
>> @@ -384,6 +386,7 @@ static inline void __maybe_unused remove_quirk(struct mmc_card *card, int data)
>> #define mmc_card_set_present(c) ((c)->state |= MMC_STATE_PRESENT)
>> #define mmc_card_set_readonly(c) ((c)->state |= MMC_STATE_READONLY)
>> #define mmc_card_set_highspeed(c) ((c)->state |= MMC_STATE_HIGHSPEED)
>> +#define mmc_card_set_hs200(c) ((c)->state |= MMC_STATE_HIGHSPEED_200)
>> #define mmc_card_set_blockaddr(c) ((c)->state |= MMC_STATE_BLOCKADDR)
>> #define mmc_card_set_ddr_mode(c) ((c)->state |= MMC_STATE_HIGHSPEED_DDR)
>> #define mmc_card_set_uhs(c) ((c)->state |= MMC_STATE_ULTRAHIGHSPEED)
>> diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h
>> index 9a03d03..606c8c3 100644
>> --- a/include/linux/mmc/host.h
>> +++ b/include/linux/mmc/host.h
>> @@ -56,10 +56,13 @@ struct mmc_ios {
>> #define MMC_TIMING_UHS_SDR50 3
>> #define MMC_TIMING_UHS_SDR104 4
>> #define MMC_TIMING_UHS_DDR50 5
>> +#define MMC_TIMING_MMC_HS200 6
>>
>> #define MMC_SDR_MODE 0
>> #define MMC_1_2V_DDR_MODE 1
>> #define MMC_1_8V_DDR_MODE 2
>> +#define MMC_1_2V_SDR_MODE 3
>> +#define MMC_1_8V_SDR_MODE 4
>>
>> unsigned char signal_voltage; /* signalling voltage (1.8V or 3.3V) */
>>
>> @@ -148,7 +151,9 @@ struct mmc_host_ops {
>> void (*init_card)(struct mmc_host *host, struct mmc_card *card);
>>
>> int (*start_signal_voltage_switch)(struct mmc_host *host, struct mmc_ios *ios);
>> - int (*execute_tuning)(struct mmc_host *host);
>> +
>> + /* The tuning command opcode value is different for SD and eMMC cards */
>> + int (*execute_tuning)(struct mmc_host *host, u32 opcode);
>> void (*enable_preset_value)(struct mmc_host *host, bool enable);
>> int (*select_drive_strength)(unsigned int max_dtr, int host_drv, int card_drv);
>> void (*hw_reset)(struct mmc_host *host);
>> @@ -242,6 +247,10 @@ struct mmc_host {
>> #define MMC_CAP2_CACHE_CTRL (1 << 1) /* Allow cache control */
>> #define MMC_CAP2_POWEROFF_NOTIFY (1 << 2) /* Notify poweroff supported */
>> #define MMC_CAP2_NO_MULTI_READ (1 << 3) /* Multiblock reads don't work */
>> +#define MMC_CAP2_HS200_1_8V_SDR (1 << 4) /* can support */
>> +#define MMC_CAP2_HS200_1_2V_SDR (1 << 5) /* can support */
>> +#define MMC_CAP2_HS200 (MMC_CAP2_HS200_1_8V_SDR | \
>> + MMC_CAP2_HS200_1_2V_SDR)
>>
>> mmc_pm_flag_t pm_caps; /* supported pm features */
>> unsigned int power_notify_type;
>> diff --git a/include/linux/mmc/mmc.h b/include/linux/mmc/mmc.h
>> index 665548e..2c8cc69 100644
>> --- a/include/linux/mmc/mmc.h
>> +++ b/include/linux/mmc/mmc.h
>> @@ -51,6 +51,7 @@
>> #define MMC_READ_SINGLE_BLOCK 17 /* adtc [31:0] data addr R1 */
>> #define MMC_READ_MULTIPLE_BLOCK 18 /* adtc [31:0] data addr R1 */
>> #define MMC_SEND_TUNING_BLOCK 19 /* adtc R1 */
>> +#define MMC_SEND_TUNING_BLOCK_HS200 21 /* adtc R1 */
>>
>> /* class 3 */
>> #define MMC_WRITE_DAT_UNTIL_STOP 20 /* adtc [31:0] data addr R1 */
>> @@ -339,13 +340,76 @@ struct _mmc_csd {
>>
>> #define EXT_CSD_CARD_TYPE_26 (1<<0) /* Card can run at 26MHz */
>> #define EXT_CSD_CARD_TYPE_52 (1<<1) /* Card can run at 52MHz */
>> -#define EXT_CSD_CARD_TYPE_MASK 0xF /* Mask out reserved bits */
>> +#define EXT_CSD_CARD_TYPE_MASK 0x3F /* Mask out reserved bits */
>> #define EXT_CSD_CARD_TYPE_DDR_1_8V (1<<2) /* Card can run at 52MHz */
>> /* DDR mode @1.8V or 3V I/O */
>> #define EXT_CSD_CARD_TYPE_DDR_1_2V (1<<3) /* Card can run at 52MHz */
>> /* DDR mode @1.2V I/O */
>> #define EXT_CSD_CARD_TYPE_DDR_52 (EXT_CSD_CARD_TYPE_DDR_1_8V \
>> | EXT_CSD_CARD_TYPE_DDR_1_2V)
>> +#define EXT_CSD_CARD_TYPE_SDR_1_8V (1<<4) /* Card can run at 200MHz */
>> +#define EXT_CSD_CARD_TYPE_SDR_1_2V (1<<5) /* Card can run at 200MHz */
>> + /* SDR mode @1.2V I/O */
>> +
>> +#define EXT_CSD_CARD_TYPE_SDR_200 (EXT_CSD_CARD_TYPE_SDR_1_8V \
>> + | EXT_CSD_CARD_TYPE_SDR_1_2V)
>> +
>
> Normal kernel coding style is:
>
Will update it as per feed back. I had taken above
EXT_CSD_CARD_TYPE_DDR_52 as reference.
> #define EXT_CSD_CARD_TYPE_SDR_200 (EXT_CSD_CARD_TYPE_SDR_1_8V | \
> EXT_CSD_CARD_TYPE_SDR_1_2V)
>
>> +#define EXT_CSD_CARD_TYPE_SDR_ALL (EXT_CSD_CARD_TYPE_SDR_200 \
>> + | EXT_CSD_CARD_TYPE_52 \
>> + | EXT_CSD_CARD_TYPE_26)
>> +
>> +#define EXT_CSD_CARD_TYPE_SDR_1_2V_ALL (EXT_CSD_CARD_TYPE_SDR_1_2V \
>> + | EXT_CSD_CARD_TYPE_52 \
>> + | EXT_CSD_CARD_TYPE_26)
>> +
>> +#define EXT_CSD_CARD_TYPE_SDR_1_8V_ALL (EXT_CSD_CARD_TYPE_SDR_1_8V \
>> + | EXT_CSD_CARD_TYPE_52 \
>> + | EXT_CSD_CARD_TYPE_26)
>> +
>> +#define EXT_CSD_CARD_TYPE_SDR_1_2V_DDR_1_8V (EXT_CSD_CARD_TYPE_SDR_1_2V \
>> + | EXT_CSD_CARD_TYPE_DDR_1_8V \
>> + | EXT_CSD_CARD_TYPE_52 \
>> + | EXT_CSD_CARD_TYPE_26)
>> +
>> +#define EXT_CSD_CARD_TYPE_SDR_1_8V_DDR_1_8V (EXT_CSD_CARD_TYPE_SDR_1_8V \
>> + | EXT_CSD_CARD_TYPE_DDR_1_8V \
>> + | EXT_CSD_CARD_TYPE_52 \
>> + | EXT_CSD_CARD_TYPE_26)
>> +
>> +#define EXT_CSD_CARD_TYPE_SDR_1_2V_DDR_1_2V (EXT_CSD_CARD_TYPE_SDR_1_2V \
>> + | EXT_CSD_CARD_TYPE_DDR_1_2V \
>> + | EXT_CSD_CARD_TYPE_52 \
>> + | EXT_CSD_CARD_TYPE_26)
>> +
>> +#define EXT_CSD_CARD_TYPE_SDR_1_8V_DDR_1_2V (EXT_CSD_CARD_TYPE_SDR_1_8V \
>> + | EXT_CSD_CARD_TYPE_DDR_1_2V \
>> + | EXT_CSD_CARD_TYPE_52 \
>> + | EXT_CSD_CARD_TYPE_26)
>> +
>> +#define EXT_CSD_CARD_TYPE_SDR_1_2V_DDR_52 (EXT_CSD_CARD_TYPE_SDR_1_2V \
>> + | EXT_CSD_CARD_TYPE_DDR_52 \
>> + | EXT_CSD_CARD_TYPE_52 \
>> + | EXT_CSD_CARD_TYPE_26)
>> +
>> +#define EXT_CSD_CARD_TYPE_SDR_1_8V_DDR_52 (EXT_CSD_CARD_TYPE_SDR_1_8V \
>> + | EXT_CSD_CARD_TYPE_DDR_52 \
>> + | EXT_CSD_CARD_TYPE_52 \
>> + | EXT_CSD_CARD_TYPE_26)
>> +
>> +#define EXT_CSD_CARD_TYPE_SDR_ALL_DDR_1_8V (EXT_CSD_CARD_TYPE_SDR_200 \
>> + | EXT_CSD_CARD_TYPE_DDR_1_8V \
>> + | EXT_CSD_CARD_TYPE_52 \
>> + | EXT_CSD_CARD_TYPE_26)
>> +
>> +#define EXT_CSD_CARD_TYPE_SDR_ALL_DDR_1_2V (EXT_CSD_CARD_TYPE_SDR_200 \
>> + | EXT_CSD_CARD_TYPE_DDR_1_2V \
>> + | EXT_CSD_CARD_TYPE_52 \
>> + | EXT_CSD_CARD_TYPE_26)
>> +
>> +#define EXT_CSD_CARD_TYPE_SDR_ALL_DDR_52 (EXT_CSD_CARD_TYPE_SDR_200 \
>> + | EXT_CSD_CARD_TYPE_DDR_52 \
>> + | EXT_CSD_CARD_TYPE_52 \
>> + | EXT_CSD_CARD_TYPE_26)
>>
>> #define EXT_CSD_BUS_WIDTH_1 0 /* Card is in 1 bit mode */
>> #define EXT_CSD_BUS_WIDTH_4 1 /* Card is in 4 bit mode */
>
> Thanks,
>
> - Chris.
> --
> Chris Ball <cjb@laptop.org> <http://printf.net/>
> One Laptop Per Child
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2012-01-03 6:14 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2011-12-23 7:12 [PATCH V8 0/2] HS200 Mode support for device and host Girish K S
2011-12-23 7:12 ` [PATCH V8 1/2] mmc: core: HS200 mode support for eMMC 4.5 Girish K S
2011-12-23 9:06 ` Subhash Jadavani
2012-01-02 22:51 ` Chris Ball
2012-01-03 6:14 ` Girish K S
2011-12-23 7:12 ` [PATCH V8 2/2] mmc: host: Adds support for eMMC 4.5 HS200 mode Girish K S
2011-12-29 11:49 ` [PATCH V8 0/2] HS200 Mode support for device and host Girish K S
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox