[PATCH 0/3] mtd: gpmi: add subpage read support

[Huang Shijie <b32955@freescale.com>]

1) Why add the subpage read support?
  The page size of the nand chip becomes larger and larger, the imx6 has to
  supports the 16K page or even bigger page. But sometimes, the upper layer only
  needs a small part of the page, such as 512 bytes or less.

  For example, ubiattach may only read 64 bytes per page.

2) We only enable the subpage read support when it meets the conditions:
   <1> the chip is imx6 (or later chips) which can supports large nand page.
   <2> the size of ECC parity is byte aligned.
       If the size of ECC parity is not byte aligned, the calling of NAND_CMD_RNDOUT
       will fail.

3) What does this patch set do?
   patch 1: add a new argument for read_subpage hook
   patch 2: do not use the mtd->writesize. 
   patch 3: This patch will fake a virtual small page for the subpage read,
            and call the gpmi_ecc_read_page() to do the real work.
            In order to fake a virtual small page, the patch changes
	    the BCH registers and the bch_geometry{}. After the subpage read
	    finished, we will restore them back.

4) Performace:
    4.1) Tested with Toshiba TC58NVG2S0F(4096 + 224) with the following command:
         #ubiattach /dev/ubi_ctrl -m 4

       The detail information of /dev/mtd4 shows below:
       --------------------------------------------------------------
       #mtdinfo /dev/mtd4
        mtd4
        Name:                           test
        Type:                           nand
        Eraseblock size:                262144 bytes, 256.0 KiB
        Amount of eraseblocks:          1856 (486539264 bytes, 464.0 MiB)
        Minimum input/output unit size: 4096 bytes
        Sub-page size:                  4096 bytes
        OOB size:                       224 bytes
        Character device major/minor:   90:8
        Bad blocks are allowed:         true
        Device is writable:             true
       --------------------------------------------------------------

    4.2) Before this patch:
       --------------------------------------------------------------
       [   94.530495] UBI: attaching mtd4 to ubi0
       [   98.928850] UBI: scanning is finished
       [   98.953594] UBI: attached mtd4 (name "test", size 464 MiB) to ubi0
       [   98.958562] UBI: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
       [   98.964076] UBI: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
       [   98.969518] UBI: VID header offset: 4096 (aligned 4096), data offset: 8192
       [   98.975128] UBI: good PEBs: 1856, bad PEBs: 0, corrupted PEBs: 0
       [   98.979843] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
       [   98.985878] UBI: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 2024916145
       [   98.993635] UBI: available PEBs: 0, total reserved PEBs: 1856, PEBs reserved for bad PEB handling: 40
       [   99.001807] UBI: background thread "ubi_bgt0d" started, PID 831
       --------------------------------------------------------------
       The attach time is about 98.9 - 94.5 = 4.4s

    4.3) After this patch:
       --------------------------------------------------------------
       [  286.464906] UBI: attaching mtd4 to ubi0
       [  289.186129] UBI: scanning is finished
       [  289.211416] UBI: attached mtd4 (name "test", size 464 MiB) to ubi0
       [  289.216360] UBI: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
       [  289.221858] UBI: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
       [  289.227293] UBI: VID header offset: 4096 (aligned 4096), data offset: 8192
       [  289.232878] UBI: good PEBs: 1856, bad PEBs: 0, corrupted PEBs: 0
       [  289.237628] UBI: user volume: 0, internal volumes: 1, max. volumes count: 128
       [  289.243553] UBI: max/mean erase counter: 1/1, WL threshold: 4096, image sequence number: 2024916145
       [  289.251348] UBI: available PEBs: 1812, total reserved PEBs: 44, PEBs reserved for bad PEB handling: 40
       [  289.259417] UBI: background thread "ubi_bgt0d" started, PID 847
       --------------------------------------------------------------
       The attach time is about 289.18 - 286.46 = 2.7s

     4.4) The conclusion:
       We achieve (4.4 - 2.7) / 4.4 = 38.6% faster in the ubiattach.

 5) This patch depends on the following patch:
    http://lists.infradead.org/pipermail/linux-mtd/2013-December/051091.html

Huang Shijie (3):
  mtd: nand: add "page" argument for read_subpage hook
  mtd: gpmi: do not use the mtd->writesize
  mtd: gpmi: add subpage read support

 drivers/mtd/nand/gpmi-nand/gpmi-nand.c |  102 +++++++++++++++++++++++++++++++-
 drivers/mtd/nand/nand_base.c           |    7 ++-
 include/linux/mtd/nand.h               |    2 +-
 3 files changed, 105 insertions(+), 6 deletions(-)

-- 
1.7.2.rc3