From: Graham Moore <grmoore@opensource.altera.com>
To: <linux-mtd@lists.infradead.org>
Cc: Alan Tull <atull@opensource.altera.com>,
Yves Vandervennet <yvanderv@opensource.altera.com>,
linux-kernel@vger.kernel.org,
Dinh Nguyen <dinguyen@opensource.altera.com>,
Brian Norris <computersforpeace@gmail.com>,
David Woodhouse <dwmw2@infradead.org>,
Graham Moore <grmoore@opensource.altera.com>
Subject: [PATCH V4 1/2] mtd: spi-nor: Bindings for Cadence Quad SPI Flash Controller driver.
Date: Mon, 23 Mar 2015 08:36:21 -0500 [thread overview]
Message-ID: <1427117782-14764-1-git-send-email-grmoore@opensource.altera.com> (raw)
Signed-off-by: Graham Moore <grmoore@opensource.altera.com>
---
V2: Add cdns prefix to driver-specific bindings.
V3: Use existing property "is-decoded-cs" instead of creating a duplicate,
"ext-decoder". Timing parameters are in nanoseconds, not master reference
clocks. Remove bus-num completely.
---
.../devicetree/bindings/mtd/cadence_quadspi.txt | 50 ++++++++++++++++++++
1 file changed, 50 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mtd/cadence_quadspi.txt
diff --git a/Documentation/devicetree/bindings/mtd/cadence_quadspi.txt b/Documentation/devicetree/bindings/mtd/cadence_quadspi.txt
new file mode 100644
index 0000000..1cf0d7e
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/cadence_quadspi.txt
@@ -0,0 +1,50 @@
+* Cadence Quad SPI controller
+
+Required properties:
+- compatible : Should be "cdns,qspi-nor".
+- reg : Contains two entries, each of which is a tuple consisting of a
+ physical address and length. The first entry is the address and
+ length of the controller register set. The second entry is the
+ address and length of the QSPI Controller data area.
+- interrupts : Unit interrupt specifier for the controller interrupt.
+- clocks : phandle to the Quad SPI clock.
+- fifo-depth : Size of the data FIFO in words.
+
+Optional properties:
+- is-decoded-cs : Flag to indicate whether decoder is used or not.
+
+Optional subnodes:
+Subnodes of the Cadence Quad SPI controller are spi slave nodes with additional
+custom properties:
+- cdns,page-size : Size, in bytes, of the device's write page
+- cdns,block-size : Size of the device's erase block
+- cdns,read-delay : Delay for read capture logic, in clock cycles
+- cdns,tshsl-ns : Delay in nanoseconds for the length that the master mode chip select outputs are de-asserted between transactions.
+- cdns,tsd2d-ns : Delay in nanoseconds between one chip select being de-activated and the activation of another.
+- cdns,tchsh-ns : Delay in nanoseconds between last bit of current transaction and deasserting the device chip select (qspi_n_ss_out).
+- cdns,tslch-ns : Delay in nanoseconds between setting qspi_n_ss_out low and first bit transfer.
+
+Example:
+
+ qspi: spi@ff705000 {
+ compatible = "cdns,qspi-nor";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0xff705000 0x1000>,
+ <0xffa00000 0x1000>;
+ interrupts = <0 151 4>;
+ clocks = <&qspi_clk>;
+ is-decoded-cs = <1>;
+ fifo-depth = <128>;
+
+ flash0: n25q00@0 {
+ ...
+ cdns,page-size = <256>;
+ cdns,block-size = <16>;
+ cdns,read-delay = <4>;
+ cdns,tshsl-ns = <50>;
+ cdns,tsd2d-ns = <50>;
+ cdns,tchsh-ns = <4>;
+ cdns,tslch-ns = <4>;
+ }
+ }
--
1.7.9.5
next reply other threads:[~2015-03-23 13:40 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-03-23 13:36 Graham Moore [this message]
2015-03-23 13:36 ` [PATCH V4 2/2] mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller Graham Moore
2015-05-11 13:50 ` Graham Moore
2015-05-20 22:26 ` Brian Norris
2015-06-01 13:49 ` Graham Moore
2015-07-24 12:45 ` [PATCH V4 1/2] mtd: spi-nor: Bindings for Cadence Quad SPI Flash Controller driver Marek Vasut
2015-07-24 16:12 ` Graham Moore
2015-07-24 16:25 ` Marek Vasut
2015-07-24 17:16 ` Graham Moore
2015-07-24 19:57 ` Marek Vasut
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1427117782-14764-1-git-send-email-grmoore@opensource.altera.com \
--to=grmoore@opensource.altera.com \
--cc=atull@opensource.altera.com \
--cc=computersforpeace@gmail.com \
--cc=dinguyen@opensource.altera.com \
--cc=dwmw2@infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mtd@lists.infradead.org \
--cc=yvanderv@opensource.altera.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).