From mboxrd@z Thu Jan 1 00:00:00 1970 Message-ID: <1494578289.15376.40.camel@mhfsdcap03> Subject: Re: [PATCH v2 3/3] mtd: nand: mediatek: add support for MT2712 NAND FLASH Controller From: xiaolei li To: Boris Brezillon CC: , , , , , , , , Date: Fri, 12 May 2017 16:38:09 +0800 In-Reply-To: <20170512085904.069e7bdd@bbrezillon> References: <1494563603-37716-1-git-send-email-xiaolei.li@mediatek.com> <1494563603-37716-4-git-send-email-xiaolei.li@mediatek.com> <20170512085904.069e7bdd@bbrezillon> Content-Type: text/plain; charset="UTF-8" Content-Transfer-Encoding: 7bit MIME-Version: 1.0 List-Id: Linux MTD discussion mailing list List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , On Fri, 2017-05-12 at 08:59 +0200, Boris Brezillon wrote: > On Fri, 12 May 2017 12:33:23 +0800 > Xiaolei Li wrote: > > > MT2712 NAND FLASH Controller is similar to MT2701 except those following: > > (1) MT2712 supports up to 148B spare size per 1KB size sector (the same > > with 74B spare size per 512B size sector). There are three new spare > > format: 61, 67, 74. > > (2) MT2712 supports up to 80 bit ecc strength. There are three new ecc > > strength level: 68, 72, 80. > > (3) MT2712 ECC encode parity data register's start offset is 0x300, and > > different with 0x10 of MT2701. > > (4) MT2712 improves ecc irq function. When ECC works in ECC_NFI_MODE, > > MT2701 will generate ecc irq number the same with ecc steps during > > page read. However, MT2712 can only generate one ecc irq. > > > > Changes of this patch are: > > (1) add two new variables named pg_irq_sel, encode_parity_reg0 in struct > > mtk_ecc_devdata. > > (2) add three new ecc level: ECC_CNFG_68BIT, ECC_CNFG_72BIT, > > ECC_CNFG_80BIT. > > (3) add new bitfield ECC_PG_IRQ_SEL for register ECC_IRQ_REG. > > (4) add three new spare format: PAGEFMT_SPARE_61, PAGEFMT_SPARE_67, > > PAGEFMT_SPARE_74. > > (5) add mt2712 nfc and ecc device compatiable and data. > > > > Signed-off-by: Xiaolei Li > > --- > > drivers/mtd/nand/mtk_ecc.c | 45 ++++++++++++++++++++++++++++++++++++---- > > drivers/mtd/nand/mtk_nand.c | 50 +++++++++++++++++++++++++++++++++++++++++++++ > > 2 files changed, 91 insertions(+), 4 deletions(-) > > > > diff --git a/drivers/mtd/nand/mtk_ecc.c b/drivers/mtd/nand/mtk_ecc.c > > index 94d0791..ac46fb0 100644 > > --- a/drivers/mtd/nand/mtk_ecc.c > > +++ b/drivers/mtd/nand/mtk_ecc.c > > @@ -28,6 +28,7 @@ > > > > #define ECC_IDLE_MASK BIT(0) > > #define ECC_IRQ_EN BIT(0) > > +#define ECC_PG_IRQ_SEL BIT(1) > > #define ECC_OP_ENABLE (1) > > #define ECC_OP_DISABLE (0) > > > > @@ -53,11 +54,13 @@ > > #define ECC_CNFG_52BIT (0x11) > > #define ECC_CNFG_56BIT (0x12) > > #define ECC_CNFG_60BIT (0x13) > > +#define ECC_CNFG_68BIT (0x14) > > +#define ECC_CNFG_72BIT (0x15) > > +#define ECC_CNFG_80BIT (0x16) > > We could get rid of these defs and just use the index of the strength > table (named ecc_level in your patch). OK. > > > #define ECC_MODE_SHIFT (5) > > #define ECC_MS_SHIFT (16) > > #define ECC_ENCDIADDR (0x08) > > #define ECC_ENCIDLE (0x0C) > > -#define ECC_ENCPAR(x) (0x10 + (x) * sizeof(u32)) > > #define ECC_ENCIRQ_EN (0x80) > > #define ECC_ENCIRQ_STA (0x84) > > #define ECC_DECCON (0x100) > > @@ -80,6 +83,8 @@ > > struct mtk_ecc_devdata { > > u32 err_mask; > > u8 max_ecc_strength; > > + u32 encode_parity_reg0; > > + int pg_irq_sel; > > }; > > > > struct mtk_ecc { > > @@ -207,6 +212,15 @@ static void mtk_ecc_config(struct mtk_ecc *ecc, struct mtk_ecc_config *config) > > case 60: > > ecc_bit = ECC_CNFG_60BIT; > > break; > > + case 68: > > + ecc_bit = ECC_CNFG_68BIT; > > + break; > > + case 72: > > + ecc_bit = ECC_CNFG_72BIT; > > + break; > > + case 80: > > + ecc_bit = ECC_CNFG_80BIT; > > + break; > > default: > > dev_err(ecc->dev, "invalid strength %d, default to 4 bits\n", > > config->strength); > > @@ -318,6 +332,7 @@ struct mtk_ecc *of_mtk_ecc_get(struct device_node *of_node) > > int mtk_ecc_enable(struct mtk_ecc *ecc, struct mtk_ecc_config *config) > > { > > enum mtk_ecc_operation op = config->op; > > + u16 reg_val; > > int ret; > > > > ret = mutex_lock_interruptible(&ecc->lock); > > @@ -331,7 +346,15 @@ int mtk_ecc_enable(struct mtk_ecc *ecc, struct mtk_ecc_config *config) > > writew(ECC_OP_ENABLE, ecc->regs + ECC_CTL_REG(op)); > > > > init_completion(&ecc->done); > > - writew(ECC_IRQ_EN, ecc->regs + ECC_IRQ_REG(op)); > > + reg_val = ECC_IRQ_EN; > > + /* > > + * For ECC_NFI_MODE, if ecc->devdata->pg_irq_sel is 1, then it > > + * means this chip can only generate one ecc irq during page > > + * read / write. If is 0, generate one ecc irq each ecc step. > > + */ > > + if ((ecc->devdata->pg_irq_sel) && (config->mode == ECC_NFI_MODE)) > > + reg_val |= ECC_PG_IRQ_SEL; > > + writew(reg_val, ecc->regs + ECC_IRQ_REG(op)); > > > > return 0; > > } > > @@ -401,7 +424,9 @@ int mtk_ecc_encode(struct mtk_ecc *ecc, struct mtk_ecc_config *config, > > len = (config->strength * ECC_PARITY_BITS + 7) >> 3; > > > > /* write the parity bytes generated by the ECC back to temp buffer */ > > - __ioread32_copy(ecc->eccdata, ecc->regs + ECC_ENCPAR(0), round_up(len, 4)); > > + __ioread32_copy(ecc->eccdata, > > + ecc->regs + ecc->devdata->encode_parity_reg0, > > + round_up(len, 4)); > > > > /* copy into possibly unaligned OOB region with actual length */ > > memcpy(data + bytes, ecc->eccdata, len); > > @@ -417,7 +442,7 @@ int mtk_ecc_encode(struct mtk_ecc *ecc, struct mtk_ecc_config *config, > > void mtk_ecc_adjust_strength(struct mtk_ecc *ecc, u32 *p) > > { > > u32 ecc_level[] = {4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36, > > - 40, 44, 48, 52, 56, 60}; > > + 40, 44, 48, 52, 56, 60, 68, 72, 80}; > > Please try to align on the open curly brace. > OK. > > int i; > > > > if (*p >= ecc->devdata->max_ecc_strength) { > > @@ -442,12 +467,24 @@ void mtk_ecc_adjust_strength(struct mtk_ecc *ecc, u32 *p) > > static const struct mtk_ecc_devdata mtk_ecc_devdata_mt2701 = { > > .err_mask = 0x3f, > > .max_ecc_strength = 60, > > + .encode_parity_reg0 = 0x10, > > + .pg_irq_sel = 0, > > +}; > > + > > +static const struct mtk_ecc_devdata mtk_ecc_devdata_mt2712 = { > > + .err_mask = 0x7f, > > + .max_ecc_strength = 80, > > + .encode_parity_reg0 = 0x300, > > + .pg_irq_sel = 1, > > }; > > > > static const struct of_device_id mtk_ecc_dt_match[] = { > > { > > .compatible = "mediatek,mt2701-ecc", > > .data = &mtk_ecc_devdata_mt2701, > > + }, { > > + .compatible = "mediatek,mt2712-ecc", > > + .data = &mtk_ecc_devdata_mt2712, > > }, > > {}, > > }; > > diff --git a/drivers/mtd/nand/mtk_nand.c b/drivers/mtd/nand/mtk_nand.c > > index 1a64ea2..5bdeace 100644 > > --- a/drivers/mtd/nand/mtk_nand.c > > +++ b/drivers/mtd/nand/mtk_nand.c > > @@ -168,9 +168,12 @@ enum mtk_nfc_spare_format { > > PAGEFMT_SPARE_50, > > PAGEFMT_SPARE_51, > > PAGEFMT_SPARE_52, > > + PAGEFMT_SPARE_61, > > PAGEFMT_SPARE_62, > > PAGEFMT_SPARE_63, > > PAGEFMT_SPARE_64, > > + PAGEFMT_SPARE_67, > > + PAGEFMT_SPARE_74, > > }; > > > > static const u32 mtk_nfc_spare_format_mt2701[] = { > > @@ -187,9 +190,34 @@ enum mtk_nfc_spare_format { > > [PAGEFMT_SPARE_50] = (10 << 4), > > [PAGEFMT_SPARE_51] = (11 << 4), > > [PAGEFMT_SPARE_52] = (12 << 4), > > + [PAGEFMT_SPARE_61] = (0 << 4), > > [PAGEFMT_SPARE_62] = (13 << 4), > > [PAGEFMT_SPARE_63] = (14 << 4), > > [PAGEFMT_SPARE_64] = (15 << 4), > > + [PAGEFMT_SPARE_67] = (0 << 4), > > + [PAGEFMT_SPARE_74] = (0 << 4), > > +}; > > + > > +static const u32 mtk_nfc_spare_format_mt2712[] = { > > + [PAGEFMT_SPARE_16] = (0 << 16), > > + [PAGEFMT_SPARE_26] = (1 << 16), > > + [PAGEFMT_SPARE_27] = (2 << 16), > > + [PAGEFMT_SPARE_28] = (3 << 16), > > + [PAGEFMT_SPARE_32] = (4 << 16), > > + [PAGEFMT_SPARE_36] = (5 << 16), > > + [PAGEFMT_SPARE_40] = (6 << 16), > > + [PAGEFMT_SPARE_44] = (7 << 16), > > + [PAGEFMT_SPARE_48] = (8 << 16), > > + [PAGEFMT_SPARE_49] = (9 << 16), > > + [PAGEFMT_SPARE_50] = (10 << 16), > > + [PAGEFMT_SPARE_51] = (11 << 16), > > + [PAGEFMT_SPARE_52] = (12 << 16), > > + [PAGEFMT_SPARE_61] = (14 << 16), > > + [PAGEFMT_SPARE_62] = (13 << 16), > > + [PAGEFMT_SPARE_63] = (15 << 16), > > + [PAGEFMT_SPARE_64] = (16 << 16), > > + [PAGEFMT_SPARE_67] = (17 << 16), > > + [PAGEFMT_SPARE_74] = (18 << 16), > > }; > > It really looks like the page format id is the index of the spare_size > array. I think you can get rid of the PAGEFMT_SPARE_ definitions if you > use the for loop I suggested in patch 2. > OK. follow your suggestion. > > > > /* > > @@ -200,6 +228,11 @@ enum mtk_nfc_spare_format { > > 16, 26, 27, 28, 32, 36, 40, 44, 48, 49, 50, 51, 52, 62, 63, 64, 255 > > }; > > > > +static const u8 spare_size_mt2712[] = { > > + 16, 26, 27, 28, 32, 36, 40, 44, 48, 49, 50, 51, 52, 61, 62, 63, 64, 67, > > + 74, 255 > > +}; > > + > > static inline struct mtk_nfc_nand_chip *to_mtk_nand(struct nand_chip *nand) > > { > > return container_of(nand, struct mtk_nfc_nand_chip, nand); > > @@ -430,6 +463,9 @@ static int mtk_nfc_hw_runtime_config(struct mtd_info *mtd) > > case 52: > > fmt |= sparefmt[PAGEFMT_SPARE_52]; > > break; > > + case 61: > > + fmt |= sparefmt[PAGEFMT_SPARE_61]; > > + break; > > case 62: > > fmt |= sparefmt[PAGEFMT_SPARE_62]; > > break; > > @@ -439,6 +475,12 @@ static int mtk_nfc_hw_runtime_config(struct mtd_info *mtd) > > case 64: > > fmt |= sparefmt[PAGEFMT_SPARE_64]; > > break; > > + case 67: > > + fmt |= sparefmt[PAGEFMT_SPARE_67]; > > + break; > > + case 74: > > + fmt |= sparefmt[PAGEFMT_SPARE_74]; > > + break; > > default: > > dev_err(nfc->dev, "invalid spare per sector %d\n", spare); > > return -EINVAL; > > @@ -1395,10 +1437,18 @@ static int mtk_nfc_nand_chips_init(struct device *dev, struct mtk_nfc *nfc) > > .spare_size = spare_size_mt2701, > > }; > > > > +static const struct mtk_nfc_devdata mtk_nfc_devdata_mt2712 = { > > + .spare_format = mtk_nfc_spare_format_mt2712, > > + .spare_size = spare_size_mt2712, > > +}; > > + > > static const struct of_device_id mtk_nfc_id_table[] = { > > { > > .compatible = "mediatek,mt2701-nfc", > > .data = &mtk_nfc_devdata_mt2701, > > + }, { > > + .compatible = "mediatek,mt2712-nfc", > > + .data = &mtk_nfc_devdata_mt2712, > > }, > > {} > > }; >