From: Xiaolei Li <xiaolei.li@mediatek.com>
To: <boris.brezillon@free-electrons.com>,
<computersforpeace@gmail.com>, <matthias.bgg@gmail.com>
Cc: <dwmw2@infradead.org>, <linux-mtd@lists.infradead.org>,
<linux-mediatek@lists.infradead.org>, <robh+dt@kernel.org>,
<rogercc.lin@mediatek.com>, <yt.shen@mediatek.com>,
<srv_heupstream@mediatek.com>, <xiaolei.li@mediatek.com>
Subject: [PATCH v5 0/4] Mediatek MT2712 NAND FLASH Controller driver
Date: Wed, 31 May 2017 16:26:37 +0800 [thread overview]
Message-ID: <1496219201-45414-1-git-send-email-xiaolei.li@mediatek.com> (raw)
The following patch-set adds support for Mediatek MT2712 NAND FLASH
Controller.
Changes on v5 relative to:
--------------------
tree : https://github.com/bbrezillon/linux-0day
branch : nand/next
commit :
'commit 2b12c057cc28 ("mtd: nand: brcmnand: Check flash #WP pin
status before nand erase/program")'
Patch v5:
---------
- rename variable j as closest_spare in function mtk_nfc_set_spare_per_sector
- remove unneeded parenthesis
- add define MTK_NFC_MIN_SPARE to check whether there is no entry that is
less than *sps.
Patch v4:
---------
- remove spare size array sort. iterate over all entries of spare size
table and pick the best one.
Patch v3:
---------
- separate patches into 4.
- rename struct mtk_ecc_devdata and struct mtk_nfc_devdata to struct
mtk_ecc_caps and struct mtk_nfc_caps respectively.
- add variables const u8 *ecc_strength and u8 num_ecc_strength into struct
mtk_ecc_caps, and remove u8 max_ecc_strength.
- rename variabl u32 temp in function mtk_ecc_probe to u32 max_eccdata_size.
- remove ECC_CNFG_xBIT define, use a for loop to do ecc hw configuration.
- remove const u32 *spare_format from struct mtk_nfc_caps, and add variables
u8 num_spare_size and u8 pageformat_spare_shift.
- remove PAGEFMT_SPARE_ define, use a for loop to do nfc hw configuration.
- sort spare size array before setting spare size.
- fix coding style issue.
Patch v2:
---------
- sperate patches into 3.
- refine DT bindings documentation about NFC and ECC compatible.
- use ecc->devdata->encode_parity_reg0 and ecc->devdata->err_mask
directly, but hide them in define.
Tests:
------
* ubifs and jffs2 are validated on NAND device MT29F16G08ADBCA
by 'dd' command.
* all drivers/mtd/tests/* pass.
* speed test:
eraseblock write speed is 8318 KiB/s
eraseblock read speed is 11374 KiB/s
page write speed is 8155 KiB/s
page read speed is 11290 KiB/s
2 page write speed is 8217 KiB/s
2 page read speed is 11354 KiB/s
erase speed is 116472 KiB/s
2x multi-block erase speed is 352978 KiB/s
4x multi-block erase speed is 359750 KiB/s
8x multi-block erase speed is 361484 KiB/s
16x multi-block erase speed is 364116 KiB/s
32x multi-block erase speed is 364116 KiB/s
64x multi-block erase speed is 364116 KiB/s
Xiaolei Li (4):
mtd: nand: mediatek: update DT bindings
mtd: nand: mediatek: refine register NFI_PAGEFMT setting
mtd: nand: mediatek: add support for different MTK NAND FLASH
Controller IP
mtd: nand: mediatek: add support for MT2712 NAND FLASH Controller
Documentation/devicetree/bindings/mtd/mtk-nand.txt | 5 +-
drivers/mtd/nand/mtk_ecc.c | 218 ++++++++++-----------
drivers/mtd/nand/mtk_ecc.h | 2 +-
drivers/mtd/nand/mtk_nand.c | 187 +++++++++---------
4 files changed, 206 insertions(+), 206 deletions(-)
--
1.9.1
next reply other threads:[~2017-05-31 8:26 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-05-31 8:26 Xiaolei Li [this message]
2017-05-31 8:26 ` [PATCH v5 1/4] mtd: nand: mediatek: update DT bindings Xiaolei Li
2017-05-31 8:26 ` [PATCH v5 2/4] mtd: nand: mediatek: refine register NFI_PAGEFMT setting Xiaolei Li
2017-05-31 8:26 ` [PATCH v5 3/4] mtd: nand: mediatek: add support for different MTK NAND FLASH Controller IP Xiaolei Li
2017-05-31 8:26 ` [PATCH v5 4/4] mtd: nand: mediatek: add support for MT2712 NAND FLASH Controller Xiaolei Li
2017-05-31 14:32 ` [PATCH v5 0/4] Mediatek MT2712 NAND FLASH Controller driver Boris Brezillon
2017-06-01 0:51 ` xiaolei li
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1496219201-45414-1-git-send-email-xiaolei.li@mediatek.com \
--to=xiaolei.li@mediatek.com \
--cc=boris.brezillon@free-electrons.com \
--cc=computersforpeace@gmail.com \
--cc=dwmw2@infradead.org \
--cc=linux-mediatek@lists.infradead.org \
--cc=linux-mtd@lists.infradead.org \
--cc=matthias.bgg@gmail.com \
--cc=robh+dt@kernel.org \
--cc=rogercc.lin@mediatek.com \
--cc=srv_heupstream@mediatek.com \
--cc=yt.shen@mediatek.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox