From: Abhishek Sahu <absahu@codeaurora.org>
To: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: David Woodhouse <dwmw2@infradead.org>,
Brian Norris <computersforpeace@gmail.com>,
Marek Vasut <marek.vasut@gmail.com>,
Richard Weinberger <richard@nod.at>,
Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>,
Miquel Raynal <miquel.raynal@bootlin.com>,
linux-arm-msm@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-mtd@lists.infradead.org, Andy Gross <andy.gross@linaro.org>,
Archit Taneja <architt@codeaurora.org>,
Abhishek Sahu <absahu@codeaurora.org>
Subject: [PATCH v3 08/16] mtd: rawnand: qcom: erased page detection for uncorrectable errors only
Date: Fri, 25 May 2018 17:51:36 +0530 [thread overview]
Message-ID: <1527250904-21988-9-git-send-email-absahu@codeaurora.org> (raw)
In-Reply-To: <1527250904-21988-1-git-send-email-absahu@codeaurora.org>
Following is the flow in the HW if controller tries to read erased
page:
1. First ECC uncorrectable error will be generated from ECC engine
since ECC engine first calculates the ECC with all 0xff and match
the calculated ECC with ECC code in OOB (which is again all 0xff).
2. After getting ECC error, erased CW detection logic will be
applied which is different for BCH and RS ECC
a. For BCH, HW checks if all the bytes in page are 0xff and then
it updates the status in separate register
NAND_ERASED_CW_DETECT_STATUS.
b. For RS ECC, the HW reports the same error when reading an
erased CW, but it notifies that it is an erased CW by
placing special characters at certain offsets in the
buffer.
So the erased CW detect status should be checked only if ECC engine
generated the uncorrectable error.
Currently for all other operational errors also (like TIMEOUT, MPU
errors, etc.), the erased CW detect logic is being applied so fix this
and return EIO for other operational errors.
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
---
* Changes from v2:
1. Changed commit message slightly
* Changes from v1:
1. Added more detail in commit message
2. Added comment before each if/else
3. Removed redundant check for BS_UNCORRECTABLE_BIT
drivers/mtd/nand/raw/qcom_nandc.c | 65 ++++++++++++++++++++++++++-------------
1 file changed, 43 insertions(+), 22 deletions(-)
diff --git a/drivers/mtd/nand/raw/qcom_nandc.c b/drivers/mtd/nand/raw/qcom_nandc.c
index 7f85ef8..9a11827 100644
--- a/drivers/mtd/nand/raw/qcom_nandc.c
+++ b/drivers/mtd/nand/raw/qcom_nandc.c
@@ -1576,6 +1576,7 @@ static int parse_read_errors(struct qcom_nand_host *host, u8 *data_buf,
struct nand_ecc_ctrl *ecc = &chip->ecc;
unsigned int max_bitflips = 0;
struct read_stats *buf;
+ bool flash_op_err = false;
int i;
buf = (struct read_stats *)nandc->reg_read_buf;
@@ -1597,8 +1598,18 @@ static int parse_read_errors(struct qcom_nand_host *host, u8 *data_buf,
buffer = le32_to_cpu(buf->buffer);
erased_cw = le32_to_cpu(buf->erased_cw);
- if (flash & (FS_OP_ERR | FS_MPU_ERR)) {
+ /*
+ * Check ECC failure for each codeword. ECC failure can
+ * happen in either of the following conditions
+ * 1. If number of bitflips are greater than ECC engine
+ * capability.
+ * 2. If this codeword contains all 0xff for which erased
+ * codeword detection check will be done.
+ */
+ if ((flash & FS_OP_ERR) && (buffer & BS_UNCORRECTABLE_BIT)) {
bool erased;
+ int ret, ecclen, extraooblen;
+ void *eccbuf;
/* ignore erased codeword errors */
if (host->bch_enabled) {
@@ -1616,29 +1627,36 @@ static int parse_read_errors(struct qcom_nand_host *host, u8 *data_buf,
continue;
}
- if (buffer & BS_UNCORRECTABLE_BIT) {
- int ret, ecclen, extraooblen;
- void *eccbuf;
+ eccbuf = oob_buf ? oob_buf + oob_len : NULL;
+ ecclen = oob_buf ? host->ecc_bytes_hw : 0;
+ extraooblen = oob_buf ? oob_len : 0;
- eccbuf = oob_buf ? oob_buf + oob_len : NULL;
- ecclen = oob_buf ? host->ecc_bytes_hw : 0;
- extraooblen = oob_buf ? oob_len : 0;
-
- /*
- * make sure it isn't an erased page reported
- * as not-erased by HW because of a few bitflips
- */
- ret = nand_check_erased_ecc_chunk(data_buf,
- data_len, eccbuf, ecclen, oob_buf,
- extraooblen, ecc->strength);
- if (ret < 0) {
- mtd->ecc_stats.failed++;
- } else {
- mtd->ecc_stats.corrected += ret;
- max_bitflips =
- max_t(unsigned int, max_bitflips, ret);
- }
+ /*
+ * make sure it isn't an erased page reported
+ * as not-erased by HW because of a few bitflips
+ */
+ ret = nand_check_erased_ecc_chunk(data_buf,
+ data_len, eccbuf, ecclen, oob_buf,
+ extraooblen, ecc->strength);
+ if (ret < 0) {
+ mtd->ecc_stats.failed++;
+ } else {
+ mtd->ecc_stats.corrected += ret;
+ max_bitflips =
+ max_t(unsigned int, max_bitflips, ret);
}
+ /*
+ * Check if MPU or any other operational error (timeout,
+ * device failure, etc.) happened for this codeword and
+ * make flash_op_err true. If flash_op_err is set, then
+ * EIO will be returned for page read.
+ */
+ } else if (flash & (FS_OP_ERR | FS_MPU_ERR)) {
+ flash_op_err = true;
+ /*
+ * No ECC or operational errors happened. Check the number of
+ * bits corrected and update the ecc_stats.corrected.
+ */
} else {
unsigned int stat;
@@ -1652,6 +1670,9 @@ static int parse_read_errors(struct qcom_nand_host *host, u8 *data_buf,
oob_buf += oob_len + ecc->bytes;
}
+ if (flash_op_err)
+ return -EIO;
+
return max_bitflips;
}
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc.
is a member of Code Aurora Forum, hosted by The Linux Foundation
next prev parent reply other threads:[~2018-05-25 12:24 UTC|newest]
Thread overview: 52+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-05-25 12:21 [PATCH v3 00/16] Update for QCOM NAND driver Abhishek Sahu
2018-05-25 12:21 ` [PATCH v3 01/16] mtd: rawnand: helper function for setting up ECC configuration Abhishek Sahu
2018-05-26 8:42 ` Miquel Raynal
2018-05-28 5:46 ` Abhishek Sahu
2018-06-07 12:37 ` Miquel Raynal
2018-06-11 9:16 ` Abhishek Sahu
2018-06-18 10:04 ` Miquel Raynal
2018-05-29 19:30 ` Boris Brezillon
2018-05-30 0:28 ` Masahiro Yamada
2018-05-30 6:21 ` Abhishek Sahu
2018-05-30 7:38 ` Masahiro Yamada
2018-05-30 8:53 ` Abhishek Sahu
2018-05-25 12:21 ` [PATCH v3 02/16] mtd: rawnand: denali: use helper function for ecc setup Abhishek Sahu
2018-05-27 9:26 ` Masahiro Yamada
2018-05-25 12:21 ` [PATCH v3 03/16] dt-bindings: qcom_nandc: make nand-ecc-strength optional Abhishek Sahu
2018-05-26 8:42 ` Miquel Raynal
2018-05-28 5:53 ` Abhishek Sahu
2018-05-25 12:21 ` [PATCH v3 04/16] dt-bindings: qcom_nandc: remove nand-ecc-step-size Abhishek Sahu
2018-05-25 12:21 ` [PATCH v3 05/16] mtd: rawnand: qcom: remove dt property nand-ecc-step-size Abhishek Sahu
2018-05-26 8:42 ` Miquel Raynal
2018-05-28 5:55 ` Abhishek Sahu
2018-05-25 12:21 ` [PATCH v3 06/16] mtd: rawnand: qcom: use the ecc strength from device parameter Abhishek Sahu
2018-05-26 8:43 ` Miquel Raynal
2018-05-28 6:01 ` Abhishek Sahu
2018-05-25 12:21 ` [PATCH v3 07/16] mtd: rawnand: qcom: wait for desc completion in all BAM channels Abhishek Sahu
2018-05-26 8:43 ` Miquel Raynal
2018-05-25 12:21 ` Abhishek Sahu [this message]
2018-05-25 12:21 ` [PATCH v3 09/16] mtd: rawnand: qcom: fix null pointer access for erased page detection Abhishek Sahu
2018-05-25 12:21 ` [PATCH v3 10/16] mtd: rawnand: qcom: parse read errors for read oob also Abhishek Sahu
2018-05-25 12:21 ` [PATCH v3 11/16] mtd: rawnand: qcom: modify write_oob to remove read codeword part Abhishek Sahu
2018-05-25 12:21 ` [PATCH v3 12/16] mtd: rawnand: qcom: fix return value for raw page read Abhishek Sahu
2018-05-26 8:43 ` Miquel Raynal
2018-05-25 12:21 ` [PATCH v3 13/16] mtd: rawnand: qcom: minor code reorganization for bad block check Abhishek Sahu
2018-05-26 8:46 ` Miquel Raynal
2018-05-28 6:12 ` Abhishek Sahu
2018-05-28 7:03 ` Miquel Raynal
2018-05-28 10:10 ` Abhishek Sahu
2018-06-07 12:53 ` Miquel Raynal
2018-06-11 13:22 ` Abhishek Sahu
2018-06-18 11:35 ` Miquel Raynal
2018-06-20 7:04 ` Abhishek Sahu
2018-05-26 8:58 ` Miquel Raynal
2018-05-28 6:16 ` Abhishek Sahu
2018-05-28 7:09 ` Miquel Raynal
2018-05-25 12:21 ` [PATCH v3 14/16] mtd: rawnand: qcom: check for operation errors in case of raw read Abhishek Sahu
2018-05-26 8:58 ` Miquel Raynal
2018-05-25 12:21 ` [PATCH v3 15/16] mtd: rawnand: qcom: helper function for " Abhishek Sahu
2018-05-27 13:53 ` Miquel Raynal
2018-05-28 7:34 ` Abhishek Sahu
2018-06-07 12:43 ` Miquel Raynal
2018-06-11 9:19 ` Abhishek Sahu
2018-05-25 12:21 ` [PATCH v3 16/16] mtd: rawnand: qcom: erased page bitflips detection Abhishek Sahu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1527250904-21988-9-git-send-email-absahu@codeaurora.org \
--to=absahu@codeaurora.org \
--cc=andy.gross@linaro.org \
--cc=architt@codeaurora.org \
--cc=boris.brezillon@bootlin.com \
--cc=computersforpeace@gmail.com \
--cc=cyrille.pitchen@wedev4u.fr \
--cc=dwmw2@infradead.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mtd@lists.infradead.org \
--cc=marek.vasut@gmail.com \
--cc=miquel.raynal@bootlin.com \
--cc=richard@nod.at \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).