From mboxrd@z Thu Jan 1 00:00:00 1970 Received: from mail02.hansenet.de ([213.191.73.62] helo=webmail.hansenet.de) by canuck.infradead.org with esmtp (Exim 4.63 #1 (Red Hat Linux)) id 1HFpRK-0003xt-7D for linux-mtd@lists.infradead.org; Sat, 10 Feb 2007 05:26:46 -0500 From: Thomas Koeller Date: Sat, 10 Feb 2007 11:21:27 +0100 Subject: [PATCH] eXcite nand flash driver To: linux-mtd@lists.infradead.org MIME-Version: 1.0 Content-Transfer-Encoding: quoted-printable Content-Disposition: inline Message-Id: <200702101121.28138.thomas.koeller@baslerweb.com> Cc: linux-mips@linux-mips.org List-Id: Linux MTD discussion mailing list List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , This is a nand flash driver for the eXcite series of intelligent cameras manufactured by Basler Vision Technologies AG. Signed-off-by: Thomas Koeller =2D-- drivers/mtd/nand/Kconfig | 8 + drivers/mtd/nand/Makefile | 1 + drivers/mtd/nand/excite_nandflash.c | 248=20 +++++++++++++++++++++++++++++++++++ 3 files changed, 257 insertions(+), 0 deletions(-) diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig index 358f55a..d188263 100644 =2D-- a/drivers/mtd/nand/Kconfig +++ b/drivers/mtd/nand/Kconfig @@ -221,6 +221,14 @@ config MTD_NAND_SHARPSL tristate "Support for NAND Flash on Sharp SL Series (C7xx + others)" depends on MTD_NAND && ARCH_PXA =20 +config MTD_NAND_BASLER_EXCITE + tristate "Support for NAND Flash on Basler eXcite" + depends on MTD_NAND && BASLER_EXCITE + help + This enables the driver for the NAND flash device found on the + Basler eXcite Smart Camera. If built as a module, the driver + will be named "excite_nandflash.ko". + config MTD_NAND_CAFE tristate "NAND support for OLPC CAF=C9 chip" depends on PCI diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile index f7a53f0..80f1dfc 100644 =2D-- a/drivers/mtd/nand/Makefile +++ b/drivers/mtd/nand/Makefile @@ -24,6 +24,7 @@ obj-$(CONFIG_MTD_NAND_NANDSIM) +=3D nands obj-$(CONFIG_MTD_NAND_CS553X) +=3D cs553x_nand.o obj-$(CONFIG_MTD_NAND_NDFC) +=3D ndfc.o obj-$(CONFIG_MTD_NAND_AT91) +=3D at91_nand.o +obj-$(CONFIG_MTD_NAND_BASLER_EXCITE) +=3D excite_nandflash.o =20 nand-objs :=3D nand_base.o nand_bbt.o cafe_nand-objs :=3D cafe.o cafe_ecc.o diff --git a/drivers/mtd/nand/excite_nandflash.c=20 b/drivers/mtd/nand/excite_nandflash.c new file mode 100644 index 0000000..7e9afc4 =2D-- /dev/null +++ b/drivers/mtd/nand/excite_nandflash.c @@ -0,0 +1,248 @@ +/* +* Copyright (C) 2005 - 2007 by Basler Vision Technologies AG +* Author: Thomas Koeller +* Original code by Thies Moeller +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License as published by +* the Free Software Foundation; either version 2 of the License, or +* (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 U= SA +*/ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#include +#include + +#include + +#define EXCITE_NANDFLASH_VERSION "0.1" + +/* I/O register offsets */ +#define EXCITE_NANDFLASH_DATA_BYTE 0x00 +#define EXCITE_NANDFLASH_STATUS_BYTE 0x0c +#define EXCITE_NANDFLASH_ADDR_BYTE 0x10 +#define EXCITE_NANDFLASH_CMD_BYTE 0x14 + +/* prefix for debug output */ +static const char module_id[] =3D "excite_nandflash"; + +/* + * partition definition + */ +static const struct mtd_partition partition_info[] =3D { + { + .name =3D "eXcite RootFS", + .offset =3D 0, + .size =3D MTDPART_SIZ_FULL + } +}; + +static inline const struct resource * +excite_nand_get_resource(struct platform_device *d, unsigned long flags, + const char *basename) +{ + char buf[80]; + + if (snprintf(buf, sizeof buf, "%s_%u", basename, d->id) >=3D sizeof buf) + return NULL; + return platform_get_resource_byname(d, flags, buf); +} + +static inline void __iomem * +excite_nand_map_regs(struct platform_device *d, const char *basename) +{ + void *result =3D NULL; + const struct resource *const r =3D + excite_nand_get_resource(d, IORESOURCE_MEM, basename); + + if (r) + result =3D ioremap_nocache(r->start, r->end + 1 - r->start); + return result; +} + +/* controller and mtd information */ +struct excite_nand_drvdata { + struct mtd_info board_mtd; + struct nand_chip board_chip; + void __iomem *regs; + void __iomem *tgt; +}; + +/* Control function */ +static void excite_nand_control(struct mtd_info *mtd, int cmd, + unsigned int ctrl) +{ + struct excite_nand_drvdata * const d =3D + container_of(mtd, struct excite_nand_drvdata, board_mtd); + + switch (ctrl) { + case NAND_CTRL_CHANGE | NAND_CTRL_CLE: + d->tgt =3D d->regs + EXCITE_NANDFLASH_CMD_BYTE; + break; + case NAND_CTRL_CHANGE | NAND_CTRL_ALE: + d->tgt =3D d->regs + EXCITE_NANDFLASH_ADDR_BYTE; + break; + case NAND_CTRL_CHANGE | NAND_NCE: + d->tgt =3D d->regs + EXCITE_NANDFLASH_DATA_BYTE; + break; + } + + if (cmd !=3D NAND_CMD_NONE) + __raw_writeb(cmd, d->tgt); +} + +/* Return 0 if flash is busy, 1 if ready */ +static int excite_nand_devready(struct mtd_info *mtd) +{ + struct excite_nand_drvdata * const drvdata =3D + container_of(mtd, struct excite_nand_drvdata, board_mtd); + + return __raw_readb(drvdata->regs + EXCITE_NANDFLASH_STATUS_BYTE); +} + +/* + * Called by device layer to remove the driver. + * The binding to the mtd and all allocated + * resources are released. + */ +static int __exit excite_nand_remove(struct device *dev) +{ + struct excite_nand_drvdata * const this =3D dev_get_drvdata(dev); + + dev_set_drvdata(dev, NULL); + + if (unlikely(!this)) { + printk(KERN_ERR "%s: called %s without private data!!", + module_id, __func__); + return -EINVAL; + } + + /* first thing we need to do is release our mtd + * then go through freeing the resource used + */ + nand_release(&this->board_mtd); + + /* free the common resources */ + iounmap(this->regs); + kfree(this); + + DEBUG(MTD_DEBUG_LEVEL1, "%s: removed\n", module_id); + return 0; +} + +/* + * Called by device layer when it finds a device matching + * one our driver can handle. This code checks to see if + * it can allocate all necessary resources then calls the + * nand layer to look for devices. +*/ +static int __init excite_nand_probe(struct device *dev) +{ + struct platform_device * const pdev =3D to_platform_device(dev); + struct excite_nand_drvdata *drvdata; /* private driver data */ + struct nand_chip *board_chip; /* private flash chip data */ + struct mtd_info *board_mtd; /* mtd info for this board */ + int scan_res; + + drvdata =3D kzalloc(sizeof(*drvdata), GFP_KERNEL); + if (unlikely(!drvdata)) { + printk(KERN_ERR "%s: no memory for drvdata\n", + module_id); + return -ENOMEM; + } + + /* bind private data into driver */ + dev_set_drvdata(dev, drvdata); + + /* allocate and map the resource */ + drvdata->regs =3D + excite_nand_map_regs(pdev, EXCITE_NANDFLASH_RESOURCE_REGS); + + if (unlikely(!drvdata->regs)) { + printk(KERN_ERR "%s: cannot reserve register region\n", + module_id); + kfree(drvdata); + return -ENXIO; + } +=09 + drvdata->tgt =3D drvdata->regs + EXCITE_NANDFLASH_DATA_BYTE; + + /* initialise our chip */ + board_chip =3D &drvdata->board_chip; + board_chip->IO_ADDR_R =3D board_chip->IO_ADDR_W =3D + drvdata->regs + EXCITE_NANDFLASH_DATA_BYTE; + board_chip->cmd_ctrl =3D excite_nand_control; + board_chip->dev_ready =3D excite_nand_devready; + board_chip->chip_delay =3D 25; + board_chip->ecc.mode =3D NAND_ECC_SOFT; + + /* link chip to mtd */ + board_mtd =3D &drvdata->board_mtd; + board_mtd->priv =3D board_chip; + + DEBUG(MTD_DEBUG_LEVEL2, "%s: device scan\n", module_id); + scan_res =3D nand_scan(&drvdata->board_mtd, 1); + + if (likely(!scan_res)) { + DEBUG(MTD_DEBUG_LEVEL2, "%s: register partitions\n", module_id); + add_mtd_partitions(&drvdata->board_mtd, partition_info, + sizeof partition_info / sizeof partition_info[0]); + } else { + iounmap(drvdata->regs); + kfree(drvdata); + printk(KERN_ERR "%s: device scan failed\n", module_id); + return -EIO; + } + return 0; +} + +static struct device_driver excite_nand_driver =3D { + .name =3D "excite_nand", + .bus =3D &platform_bus_type, + .probe =3D excite_nand_probe, + .remove =3D __exit_p(excite_nand_remove) +}; + +static int __init excite_nand_init(void) +{ + pr_info("Basler eXcite nand flash driver Version " + EXCITE_NANDFLASH_VERSION "\n"); + return driver_register(&excite_nand_driver); +} + +static void __exit excite_nand_exit(void) +{ + driver_unregister(&excite_nand_driver); +} + +module_init(excite_nand_init); +module_exit(excite_nand_exit); + +MODULE_AUTHOR("Thomas Koeller "); +MODULE_DESCRIPTION("Basler eXcite NAND-Flash driver"); +MODULE_LICENSE("GPL"); +MODULE_VERSION(EXCITE_NANDFLASH_VERSION) =2D-=20 1.4.3