Re: [PATCH] mtd: spi-nor: Add support for S3AN spi-nor devices

[Boris Brezillon <boris.brezillon@free-electrons.com>]

Hi Ricardo,

Please try to pass the version in your subject prefix (pass
--subject-prefix="PATCH vX" to git format-patch).

On Tue, 20 Sep 2016 17:45:51 +0200
Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> wrote:

> Xilinx Spartan-3AN FPGAs contain an In-System Flash where they keep
> their configuration data and (optionally) some user data.
> 
> The protocol of this flash follows most of the spi-nor standard. With
> the following differences:
> 
> - Page size might not be a power of two.
> - The address calculation (default addressing mode).
> - The spi nor commands used.
> 
> Protocol is described on Xilinx User Guide UG333
> 
> Reviewed-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
> Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
> ---
> v6:
> Suggested by: Boris Brezillon <boris.brezillon@free-electrons.com>
> -Replace triple operator with if/else
> 
> v5:
> -Rebase on top of l2-mtd/master
> Suggested by: Cyrille Pitchen <cyrille.pitchen@atmel.com>:
> -Fix to+1 bug
> -Move all address conversions to spi-nor
> -Replace pr_dev with dev_err
> 
> v4:
> -Rebase on top of l2-mtd/master
> 
> v3:
> -Rebase on top of mtd-next
> -Rename ADDR_NATIVE to ADDR_DEFAULT to follow UG333 naming
> -Fix bug on probe
> 
> v2: Suggested by Brian Norris <computersforpeace@gmail.com>
> 
> -Remove inline qualifier
> -Improve documentation of Default Addressing Mode
> -Convert function callbacks into SNOR_F_
> -Fix missmatch braces
> -Improve documentation of SPI_S3AN flag
> 
>  drivers/mtd/spi-nor/spi-nor.c | 124 ++++++++++++++++++++++++++++++++++++++++--
>  include/linux/mtd/spi-nor.h   |  12 ++++
>  2 files changed, 131 insertions(+), 5 deletions(-)
> 
> diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c
> index d0fc165d7d66..d29842177808 100644
> --- a/drivers/mtd/spi-nor/spi-nor.c
> +++ b/drivers/mtd/spi-nor/spi-nor.c

[...]

>  /*
> + * This code converts an address to the Default Address Mode, that has non
> + * power of two page sizes. We must support this mode because it is the default
> + * mode supported by Xilinx tools, it can access the whole flash area and
> + * changing over to the Power-of-two mode is irreversible and corrupts the
> + * original data.
> + */
> +static loff_t spi_nor_s3an_addr_convert(struct spi_nor *nor, unsigned int addr)
> +{
> +	unsigned int offset;
> +
> +	offset = (nor->page_size == 264) ? (addr % 264) : (addr % 528);

Can you send a new version with

	offset = addr % nor->page_size;

to see if kbuild test robot still complains.

> +
> +	return ((addr - offset) << 1) | offset;
> +}
> +

Thanks,

Boris